Home > Acer > Projector > Acer Projector Pd115 User Manual

Acer Projector Pd115 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Acer Projector Pd115 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							21... English
    User Controls
    Color
    (Computer / Video
    Mode)
    Tint
    Adjusts the color balance of red and green.
    4Press the  to increase the amount of green in the image.
    4Press the  to increase the amount of red  in the image.
    Color R
    Adjusts the red color.
    Color G
    Adjusts the green color.
    Color B
    Adjusts the blue color.     
    						
    							22English ...
    User Controls
    Keystone
    Adjust image distortion caused by tilting projection. (±16 degrees)
    Aspect Ratio
    Use this function to choose your desired aspect ratio.
    44:3 : The input source will be scaled to fit the projection screen.
    416:9 : The input source will be scaled to fit the width of the screen.
    4Auto : Keep the image with original width-higth ratio and maximize the
    image to fit native horizontal or vertical pixels.
    H.Position (Horizontal Position)
    4
    Press the  to move the image left.
    4Press the  to move the image right.
    V. Position (Vertical Position)
    4
    Press the  to move the image down.
    4Press the  to move the image up.
    Frequency
    “Frequency”changes the display data frequency to match the
    frequency of your computer’s graphic card. If you experience a
    vertical flickering bar, use this function to make an adjustment.
    Image
    (Computer / Video
    Mode)     
    						
    							23... English
    User Controls
    Tracking
    “Tracking” synchronizes the signal timing of the display with the
    graphic card. If you experience an unstable or flickering image, use
    this function to correct it.
    Sharpness
    Adjusts the sharpness of the image.
    4Press the  to decrease the sharpness.
    4Press the  to increase the sharpness.
    Image
    (Computer / Video
    Mode)
    ™“Sharpness” functions
    is not supported under
    DVI mode.       
    						
    							24English ...
    User Controls
    Audio
    (Computer / Video
    Mode)
    Volume
    4
    Press the  to decrease the volume.
    4Press the  to increase the volume.
    Mute
    4
    Choose the “On” to turn mute on.
    4Choose the “Off” to turn mute off.     
    						
    							25... English
    Lamp Mode
    4
    ECO : Selecting “ECO” mode to dim the projector Lamp, which lower power consumption, will extend the lamp life and reduce noise.
    4Standard : Apply “ Standard “ mode to reurn normal operation.
    4Enhanced : Choosing “Enhanced ” mode will brighten the projector Lamp to get a brighter screen.
    Menu Location
    Choose the Menu location on the display screen.
    Projection
    4
    Front-Desktop
    The factory default setting.
    4Rear-Desktop
    When you select this function, the projector reverses the image
    so you can project behind a translucent screen.
    4Front-Ceiling
    When you select this function, the projector turns the image
    upside down for ceiling-mounted projection.
    4Rear-Ceiling
    When you select this function, the projector reverses and turns
    the image upside down at same time. You can project from
    behind a translucent screen with ceiling mounted projection.
    User Controls
    Management (Computer
    / Video Mode)             
    						
    							26English ...
    Source Lock
    When source lock is turned off, the projector will search for other signals if
    the current input signal is lost. When source lock is turned on, it will
    “Lock” the current source channel when you press “Source” button on
    remote control for next channel.
    Lamp Hour Elapse
    Displays the lamp’s elapsed operating time (in hours).
    Lamp Hour Reset
    Press the  button after choosing “Yes ”to turn the lamp hour
    counter to 0 hours.
    Lamp Reminding
    Choose this function to show or to hide warning message when the
    changing lamp message is displayed.  The message will show up 30
    hours before end of life.
    OSD Transparency
    Adjusts the OSD’s transparency.
    Start-up Screen
    Use this function to slect your desired start-up screen. If you
    change the setting from one to another, when you exit the OSD menu, the
    new setting will take effect.
    4Acer : The default start-up screen of Acer projector.
    4User : The user customized start-up scren, which is down loaded
    from PC to projector via the USB cable and My Start-up Screen utility
    (refer to  the description of below section).
    User Controls
    Management (Computer
    / Video Mode)       
    						
    							27... English
    User Controls
    Management (Computer
    / Video Mode)
    Acer My Start-up Screen is a PC utility for user to
    change the default start-up screen of Acer projector
    to their desired image. You can install  My Start-up
    Screen  from the bundled CD. Connect  the projector to
    your PC with the bundled USB cable then execute  My
    Start-up Screen  utility to download your desired
    image from your PC to projector. Before the download
    starts, the projector must enter “Download 
    Mode”
    first. Please follow the instruction below to enter “Down-
    load Mode”.
    1. If the AC power cord of the projector was unplugged, plug the AC power.
    2. If the projector was turned on, press power button twice to turn off the\
    projector.
    3. Make sure all the fan of projector was shut down and the “Power” L\
    ED is blinking.
    4. Press and hold “Menu/Enter” button then press “ “ button.
    5. When “Temp” and “Lamp” LEDs turn on again, release both buttons, projector enters download mode.
    6. Please make sure the USB cable has been plugged and connected to your projector.
    Reset
    Press the  button after choosing Yes to return the display parameters on all
    menus to the factory default settings.         
    						
    							28English ...
    Appendices
    Problem: No image appears on screen.
    4Ensure all the cables and power connections are correctly and
    securely connected as described in the “Installation” section.
    4Ensure the pins of connectors are not crooked or broken.
    4Check if the projection lamp has been securely installed. Please
    refer to the “Replacing the lamp” section.
    4Make sure you have removed the lens cap and the projector is
    switched on.
    4Ensure that the “Hide” feature is not enabled.
    Problem: Partial, scrolling or incorrectly displayed image.
    4Press the “Re-Sync” button on the Remote Control.
    4If you use a PC:
    If the resolution of your computer is higher than 1024 x 768.
    Follow the steps outlined below to reset the resolution.
    For Windows 3.x:
    1.In the Windows Program Manager, click the “Windows Setup”
    icon in the Main group.
    2.Verify that your display resolution setting is less than or equal
    to 1024 x 768.
    For Windows 95, 98, 2000, XP:
    1.Open “My Computer” icon, the “Control Panel” folder, and
    then double click on the “Display” icon.
    2.Select the “Setting” tab.
    3.In the “Desktop Area” you will find the resolution setting.
    Verify that the resolution setting is less than or equal to 1024 x
    768  resolution.
    If the projector is still not projecting the whole image, you will
    also need to change the monitor display you are using. Refer to
    the following steps.
    4.Follow the above steps 1-2. Click on the “Advanced Properties”
    button.
    5.Select the “Change” button under the “Monitor” tab .
    Troubleshooting
    If you experience trouble with the projector, refer to
    the following information.  If the problem persists, please
    contact your local reseller or service center.   
    						
    							29... English
    Appendices
    6.Click on “Show all devices”. Then select “Standard monitor
    types” under the “Manufacturers” box ; choose the resolution
    mode you need under the “Models” box.
    7.Verify that the resolution setting of the monitor display is less
    than or equal to 1024 x 768.
    4If you are using a Notebook PC:
    1.You are required to implement the above steps of resolution
    setting of the computer first.
    2.Switch the Notebook PC display to the “external display only”
    or “CRT only” mode.
    4If you experience difficulty in changing resolutions or your
    monitor freezes, restart all the equipment and the projector.
    Problem: The screen of the Notebook or PowerBook computer is not
    displaying your presentation.
    4If you are using a Notebook PC:
    Some Notebook PCs may deactivate their screens when a second
    display device is in use.  Refer to your computer’s documentation
    for information on how to reactivate the monitor display.
    4If you are using an Apple PowerBook:
    In Control Panels, open the PowerBook Display to select Video
    Mirroring “On”.
    Problem: Image is unstable or flickering
    4Use “Tracking” to correct it.  Refer to page 23.
    4Change the monitor color setting from your computer.
    Problem: Image has vertical flickering bar
    4Use “Frequency” to make an adjustment.  Refer to page 22.
    4Check and reconfigure the display mode of your graphic card to
    make it compatible with the product.  Refer to page 28.
    Problem: Image is out of focus
    4Adjusts the Focus Ring on the projector lens.  Refer to page 14.
    4Make sure the projection screen is between the required distance
    -3.9 to 32.8 feet (1.2 to 10.0 meters) from the projector.   
    						
    							30English ...
    Appendices
    Problem: The image is outstretched when displaying 16:9
    DVD.
    The projector automatically detects 16:9 DVD and adjusts the aspect
    ratio by digitizing to full screen with 4:3 default setting.
    If the image is still outstretched, you will also need to adjust the aspect ratio
    by referring to the following:
    4Please select 4:3 aspect ratio type on your DVD player if you are
    playing a 16:9 DVD.
    4If you can’t select 4:3 aspect ratio type on your DVD player, please
    select 4:3 aspect ratio in the on screen menu.
    Problem: Image is reversed.
    4
    Select “Management” from the OSD and adjust the projection
    direction.  See page 25.
    Problem: Lamp burns out or makes a popping sound
    4
    When the lamp reaches its end of life, it will burn out and may
    make a loud popping sound.  If this happens, the projector will not
    turn on until the lamp module has been replaced. To replace
    thelamp, follow the procedures in the “Replacing the Lamp”. See
    page 32.
    Problem: LED lighting message
    MessagePower LED
    Temp LED Lamp LED
    Green
    Standby State
    Flashing   (Input power cord)
    Lamp lighting
      
    Power on  
    Power off (Cooling)  
    Error (Lamp fail)   
    Error (Thermal fail) 
    Error (Fan lock fail)  Flashing  
    Error (Over Temp.)   
    Error
      (Lamp Breakdown)
     =>Light On  =>Light Off   
    						
    All Acer manuals Comments (0)

    Related Manuals for Acer Projector Pd115 User Manual