Acer Projector Pd113p User Manual

 ... English
21
Image
(Computer Mode)
User Controls
Keystone
Adjust image distortion caused by tilting projection. ( 15 degrees)
Aspect Ratio
Use this function to choose your desired aspect ratio.
4:3 : The input source will be scaled to fit the projection screen.
16:9 : The input source will be scaled to fit the width of the screen.
Auto : Keep the image with original width-higth ratio and
maximize the image to fit native horizontal or vertical pixels.
16:9 Image Postion
Press the   to choose the image...

English...
22
Image
(Video Mode)
User Controls
Keystone
Adjust image distortion caused by tilting projection. ( 15 degrees)
Aspect Ratio
Use this function to choose your desired aspect ratio.
4:3 : The input source will be scaled to fit the projection screen.
16:9 : The input source will be scaled to fit the width of the screen.
Auto : Keep the image with original width-higth ratio and
maximize the image to fit nativer horizontal or vertical pixels.
16:9 Image Postion
Press the   to choose the image...

 ... English
23
Audio
(Computer / Video
Mode)
User Controls
Volume
Press the  to decrease the volume.
Press the  to increase the volume.
Mute
Choose the “On” to turn mute on.
Choose the “Off” to turn mute off. 

English...
24
Management
(Computer / Video
Mode)
User Controls
ECO Mode
Choose “On” to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose “Off”
to return normal mode.
Menu Location
Choose the Menu location on the display screen.
Projection
Front-Desktop
The factory default setting.
Rear-Desktop
When you select this function, the projector reverses the image so
you can project behind a translucent screen.
Front-Ceiling
When you select this function,...

 ... English
25
Management
(Computer / Video
Mode)
User Controls
Source Lock
When source lock is turned off, the projector will search for other
signals if the current input signal is lost. When source lock is turned
on, it will “Lock” the current source channel before you press “Source”
button on remote control for next channel.
Lamp Hour Elapse
Displays Hour the lamp’s elapsed operating time (in hours).
Lamp Hour Reset
Press the  button and then choose “Yes“ to turn the lamp hour
counter to 0 hours....

English...
26
Management
(Computer / Video
Mode)
Start-up Screen
Use this function to select your desired start-up screen. If you change
the setting from one to another, when you exit the OSD menu, the
new setting will take effect immediately.
Acer: The default start-up screen of Acer projector.
User: The user customized start-up screen, which is downloaded
from PC to projector via the USB cable and My Start-up Screen
utility (refer to the description of below section).
My Start-up Screen
User Controls 

 ... English
27
Acer  My Start-up Screen  is a PC utility for user to change the default
start-up screen of Acer projector to their desired image. You can instal\
l
My Start-up Screen  from the bundled CD. Connect the projector to
your PC with the bundled USB cable then execute  My Start-up Screen
utility to download your desired image from your PC to projector.
Before the download starts, the projector must enter “Download
Mode” first. Please follow the instruction below to enter “Downloa\
d
Mode”.
1....

English...
28
Troubleshooting
If you experience trouble with the projector, refer to the following
information. If the problem persists, please contact your local
reseller or service center.
Problem: No image appears on screen.
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure the pins of connectors are not crooked or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp”...

 ... English
29
4. Follow the above steps 1-2. Click on the “Advanced Properties”
button.
5. Select the “Change” button under the “Monitor” tab . than or
equal to 800 x 600.
6. Click on “Show all devices”. Then select “Standard monitor
types” under the “Manufacturers” box ; choose the resolution
mode you need under the “Models” box.
7. Verify that the resolution setting of the monitor display is less
than or equal to 800 x 600.
If you are using a Notebook PC:
1. You are required to implement the above...

English...
30Problem: The image is outstretched when displaying 16:9 DVD.
The projector automatically detects 16:9 DVD and adjusts the aspect
ratio by digitizing to full screen with 4:3 default setting.
If the image is still outstretched, you will also need to adjust the aspect
ratio by referring to the following:
Please select 4:3 aspect ratio type on your DVD player if you are
playing a 16:9 DVD.
If you can’t select 4:3 aspect ratio type on your DVD player, please
select 4:3 aspect ratio on screen...