Acer Projector Pd113 User Manual

							 ... English
31
Problem: Message Reminders
”Lamp is approaching the end of its useful life in full power
operation. Replacement Suggested!” will be shown about 10
seconds when lamp life is going to deplete.
Appendices 
						

							English...
32
Replacing the lamp
The projector will detect the lamp life itself. It will show you a warning
message “Lamp is approaching the end of its useful life in full power
operation. Replacement Suggested!” When you see this message,
changing the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30 minutes
before changing the lamp.
Do not operate the lamp longer than rated lifetime. Otherwise it could
be high possibility of lamp shattering. A compulsive putting-out-lights
function should operate by the projector side so that the lamp after a
life is not used after that for a long time. We recommend attachment
of a timer etc., and attachment of a lamp exchange display function to
a projector lighting time management of a lamp. (Recommendation
of a regular shutdown).
Appendices
Warning: Lamp
compartment is
hot! Allow it to
cool down before
changing lamp!
NOTE
1
4
3
2 
						

							 ... English
33
Lamp Changing Procedure:
1.  Turn the power off the projector by pressing the  

button.
2. Allow the projector to cool down at least 30 minutes.
3. Disconnect the power cord.
4. Use a screwdriver to remove the screw from the cover.
1
5. Push up and remove the cover. 2
6. Remove the 2 screws from the lamp module. 3
7.  Pull out the lamp module. 4
To replace the lamp module, reverse the previous steps.
Appendices
Warning:  To reduce the
risk of personal injury,
do not drop the lamp
module or touch the
lamp bulb. The bulb may
shatter and cause injury
if it is dropped.
NOTE 
						

							English...
34
Specifications
The specs specified below are subject to change without notice. Regarding the final
specs, please refer to Acer accounced marketing specs.
Light Valve - Single Chip DLP
TM Technology by Texas Instruments
Lamp - 200W User Replaceable Lamp
Number of Pixels - 800 pixels(H) X 600 lines(V)
Displayable Color - 16.7M colors
Brightness - 1600 ANSI Lumens
Contrast Ratio - 2000:1 (Full on/off) (Min)
Uniformity - 90%
Noise Level - 30 dB(A) (standard mode)/27 dB(A) (ECO mode)
Projection Lens - F2.5 (wide), F2.7 (tele), f=20.2~24.2mm with 1.2x Manual
zoom lens
Projection Screen Size (Diag.) -27.5 ~ 330 inches Diagonal
Projection Distance - 3.9 to 32.8 feet (1.2 to 10.0 meters)
Video Compatibility - NTSC/PAL/SECAM and HDTV compatible
- Composite video & S-Video capability
H. Frequency - 31kHz ~79kHz horizontal scan
V. Frequency - 50Hz ~85Hz vertical refresh
Power Supply -Universal AC input 100-240V ; Input Frequency 50/60Hz
I/O Connectors - Power: AC power input socket
- VGA Input:
One 15-pin D-sub for VGA, component and HDTV signal
- Video Input:
One Composite video RCA input
One S-Video input
- USB:One USB connector for remote computer control
- Audio Input: One phone jack for audio input
Weight - 2.0 KG (
						

							 ... English
35
Appendices
Mode Resolution Vertical Frequency (Hz) Horizontal Frequency (kHz)
60 Hz 31.5 kHz
72 Hz 37.7 kHz
75 Hz 37.5 kHz VGA 640 x 480
85 Hz 43.3 kHz
56 Hz 35.1 kHz
60 Hz 37.9 kHz
72 Hz 48.1 kHz
75 Hz 46.9 kHz SVGA 800 x 600
85 Hz 53.7 kHz
60 Hz 48.4 kHz
70 Hz 56.5 kHz
75 Hz 60.0 kHz
80 Hz 64.0 kHz XGA* 1024 x 768
85 Hz 68.3 kHz
SXGA * 1280 x 1024 60 Hz 64.0 kHz
MAC LC 
13 640x480 66.66 Hz 34.98 kHz
MAC II 13
640x480 66.68 Hz 35 kHz
MAC 16
832x624 
74.55 Hz 49.725 kHz
MAC 19 
1024x768 75 Hz 60.24 kHz
MAC
1152x870 75.06 Hz 68.68 kHz
MAC G4
640x480 60 Hz 31.35 kHz
i Mac DV
1024x768 75 Hz 60 kHz
i Mac DV
1152x870 75 Hz 68.49 kHz
i Mac DV
1280x960 75 Hz 75 kHz
Compatibility Modes
NOTE
Note : “*” means
compressed.