Acer Projector Pd110z User Manual

11
English
Installation
Connecting the Projector
1. VGA Cable
2. Power Cord
3. S-Video Cable
4. Composite Video Cable (optional)
5 USB Cable  (to connect the USB mouse to a PC; optional)
6. HDTV/Component Video Cable (optional)
™To ensure the projector works well with your computer, please set the display
mode on your graphics card to less than or equal to SVGA (800 x 600) resolution.
Also ensure the refresh rate of the graphics card is compatible with the projector.
Refer to the “Compatibility Modes”...

12
English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Remove the lens cap.
2. Ensure that the power cord and signal cable are securely connected.
3. Turn on the lamp by pressing “Power/Standby” on the control panel.\
X
The startup screen will be displayed for 20 seconds and the Power/Standb\
y indicator
will turn solid green.
4. Turn on the source (computer, notebook, or video player, etc.)  The projector will automatically detect your source.
™ If the projector displays...

13
English
Installation
Powering Off the Projector
1. Press “Power/Standby” to turn off the projector lamp. The projector will display
the message “Power off the lamp?”
2. Press “Power/Standby” again to confirm. Otherwise the message will disappear
after 5 seconds.
3. “Power/Standby” indicator will turn green for approximatly 90 seconds. When
the green light begins flashing, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has
completed...

14
English
Installation
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with an elevator foot for adjusting the projector
height.
To raise the projector:
1. Press the elevator button X.
2. Raise the projector to the desired display angle Y, then release the button to lock
the elevator foot into position.
3. Use Z to fine-tune tilt adjustment.
To lower the projector:
1. Press the elevator button X.
2. Lower the projector then release the button Y to lock the elevator...

15
English
Installation
Adjusting the Projector Focus
To adjust the focus, simply rotate the focus ring until the image is clear. The projector
will focus at distances from 4.0 feet to 39.4 feet (1.2m to 12m)
Screen29.4” 81.6”133.8” 185.3” 237.5” 289.7”
(Diagonal)
Screen23.5 x 17.7” 65.3 x 48.9” 107.1 x 80.3” 148.2 x 111.2” 190.0 x 142.5” 231.8 x 173.8”
Size (WxH)
Distance4.0’ 11.1’ 18.2’ 25.2’ 32.3’ 39.4’
™ This graph is for reference only.         

16
English
User Controls
Panel Control & Remote Control
There are two options for controlling the projector: Remote Control and Panel
Control.
Remote Control
Power / Standby
Refer to the “Power On/Off the Projector” section on page 12-13.
Optimum Setting
XPress “Optimum” to select Conference Mode  or Cinema Mode.
Source
XPress “Source” to cycle between VGA, S-Video, Composite, and Component
sources.Panel Control  Remote Control         

17
English
User Controls
Four Directional Selectors
XThese keys are used to control the direction STWX operation on the OSD display.
Page Up (Computer Mode only)
XUse this button to page up. This function is only available when the projector is
connected to a computer via an USB cable.
Page Down (Computer Mode only)
XUse this button to page down. This function is only available when the projector is
connected to a computer via a USB cable.
Menu
XPress “Menu” to launch the OSD menu and press WX
 key to...

18
English
User Controls
Use the Panel Control
Power/Standby
XRefer to the ‘Power On/Off the Projector” section on page 12-13.
Source
XPress “Source” to cycle through VGA, S-Video, Composite and Component
sources.
Re-Sync
XAutomatically synchronizes the projector to the input source.
Four Directional Select Keys
XUse
  STWX  to select items or make adjustments for your selection.
Enter
XConfirm your selection of items.
XPress “Menu” to launch the OSD menu and press WX key to select menu items.
To exit...

19
English
User Controls
OSD Menus
How to Operate
XThe projector has a multilingual OSD that allows you to make image adjustments
and change a variety of settings. With a computer source, the OSD displayed is
the “Computer OSD”. With a video source, the OSD displayed is the “Video OSD”.
The projector will automatically detect the source.
XTo launch the OSD menu, press “Menu” on the remote control or panel control.
XWhen the OSD is displayed, press WX key to select main items....

20
English
User’s Info
Edits user preferences by OSD interface. Press Menu to enter Users info.
screen, you can edit as you wish. Edited Users info will display on lower left corner
of the screen when projector is powered ON.
1. Use the WX to select Line1 function, and then press the Menu button. You
can input the character to line one.
2. Use the STWX to select character, and then press Menu to confirm your
selection.
3. Use the WX to select Line2 function, and then press the Menu button. You
can input...