Home > Acer > Projector > Acer Projector P7500 User Guide

Acer Projector P7500 User Guide

Here you can view all the pages of manual Acer Projector P7500 User Guide. The Acer manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 41

31
English3 Partial, scrolling 
or incorrectly 
displayed image
(for notebooks)•Press RESYNC on the remote control or control 
panel.
•For an incorrectly displayed image:•Follow the steps for item 2 (above) to adjust 
the resolution of your computer.
•Press the toggle output settings. Example: 
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], 
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4], 
NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]
•If you experience difficulty changing resolutions or 
your monitor freezes, restart...

Page 42

32
English
Problems with the Projector
9 Image is too small 
or too large•Adjust the zoom ring on the top of the projector.
•Move the projector closer to or further from the 
screen.
•Press MENU on the remote control or on the 
control panel. Go to Image --> Aspect Ratio and 
try different settings.
10 Image has slanted 
sides
•If possible, reposition the projector so that it is 
centered on the screen.
•Press the Keystone   /    on the control panel or 
on the remote control until the sides are...

Page 43

33
EnglishOSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its 
recommended operating temperature and must be allowed to 
cool down before it may be used. Please also check the dust 
filters if they are installed. If the dust filter is clogged with 
dust, please clean it. Please refer to Cleaning and replacing 
the dust filter for details.
Replace the lamp - the lamp is about to reach its maximum 
lifetime....

Page 44

34
English
LED & Alarm Definition Listing
LED Messages
MessageLamp LED Temp LED Power LED
Red Red Red Blue
Standby (power cord 
plugged in)-- -- V --
Power button ON -- -- -- V
Lamp retry -- -- -- Quick 
flashing
Turning off (cooling 
state)-- -- Quick 
flashing--
Turning off (cooling 
completed)-- -- V --
Error (thermal failure) -- V -- V
Error (fan lock failure) -- Quick 
flashing-- V
Error (lamp breakdown) V -- -- V
Error (color Wheel fail) Quick 
flashing-- -- V 

Page 45

35
EnglishCleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned 
periodically, they can become clogged with dust, preventing proper ventilation.  
This can cause overheating and damage the projector.
Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then 
unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Unplug the corner (Illustration #1)
4 Pull out...

Page 46

36
English
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the 
lamp.
The projector will detect the lamp life. You will be shown a warning message 
Lamp is approaching the end of its useful life in full power operation. 
Replacement Suggested! When you see this message, change the lamp as soon 
as possible. Make sure the projector has been cooling down for at least 30 
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool...

Page 47

37
EnglishCeiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the 
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and 
secure the mount base.
Note: Screws are not included. Please obtain the appropriate 
screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of four-cylinder screws.
20 mm13mm
8.4mm
130 mm
49.9mm
Ceiling Mount Base    - Attach to ceiling
Screw Type A50 mm length / 8 mm...

Page 48

38
English
3 Use the appropriate number of screws for the projector size to attach the 
projector to the ceiling mount bracket.
Note: It is recommended that you keep a reasonable space 
between the bracket and the projector to allow for proper heat 
distribution. Use two washers for extra support, if deemed 
necessary.
4 Attach the ceiling bracket to the ceiling rod.
Screw Type B
Smaller Washer
Large Washer
Projector Bracket
Supports projector and allows -   
  for adjustments     
Spacer
    - For heat...

Page 49

39
English5 Adjust the angle and positioning as necessary.
Note: The appropriate type of screw and washer for each model is 
listed in the table below. 3 mm diameter screws are enclosed in 
the screw pack.
Models Screw Type B Washer Type
Diameter (mm) Length (mm) Large Small
P7500 3 20 V V
Tightening Screw
Allen Key
Allen Key
Tightening Screw
³140.00mm
82.52mm
SCREW SPEC. M3 x 20mm 

Page 50

40
English
Specifications
The specifications listed below are subject to change without notice. For final 
specs, please refer to Acers published marketing specifications.
Projection system
DLP®
Resolution
Native: 1080P (1920 x 1080), Maximum: UXGA (1600 x 
1200),WSXGA+ (1680 x 1050), 1080p (1920 x 1080)
Computer compatibility
IBM PC and compatibles, Apple Macintosh, iMac and 
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA+
Video compatibility
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM...
Start reading Acer Projector P7500 User Guide

Related Manuals for Acer Projector P7500 User Guide

All Acer manuals