Acer Projector P5270 User Manual

							19
English
Note: H. Position, V. Position, Frequency and Tracking functions 
are not supported under DVI or Video mode.
Note: Sharpness functions is not supported under DVI and Computer 
mode.Rear-Desktop
•When you select this function, the projector reverses the image so 
you can project from behind a translucent screen.
Rear-Ceiling
•When you select this function, the projector reverses and inverts 
the image at same time. You can project from behind a 
translucent screen with ceiling mounted projection.
H. Position 
(Horizontal 
position)
•Press   to move the image left.
•Press   to to move the image right.
V. Position 
(Vertical position)
•Press   to move the image down.
•Press   to move the image up.
Frequency Frequency changes the projectors refresh rate to match the 
frequency of your computer’s graphics card. If you can see a vertical 
flickering bar in the projected image, use this function to make the 
necessary adjustments.
Tracking Synchronizes the signal timing of the projector with the graphics card. 
If you experience an unstable or flickering image, use this function to 
correct it.
Sharpeness Adjusts the sharpness of the image.
•Press   to decrease the sharpness.
•Press   to increase the sharpness. 
						

							20
English
Management setting
ECO Mode Choose On to dim the projector lamp which will lower power 
consumption, extend the lamp life and reduce noise.  Choose Off 
to return normal mode.
Auto Shutdown The projector will automatically shutdown when there is no signal 
input after the allocated time. (in minutes)
Source Lock When source lock is turned off, the projector will search for 
other signals if the current input signal is lost. When source lock is 
turned on, it will lock the current source channel unless you 
press Source button on the remote control for the next channel.
Menu Location Choose the menu location on the display screen.
Startup Screen Use this function to select your desired startup screen. If you 
change the setting, the changes will take effect when you exit the 
OSD menu.
• Acer: The default startup screen of your Acer projector.
• User: Use memorize picture from Screen Capture function.
Screen Capture Use this function to customize the startup screen. To capture the 
image that you want to use as the startup screen, follow the 
instructions below.
Notice:
Before proceeding with the following steps, make sure that the 
Keystone is set to the default value 0 and the aspect ratio is set 
to 4:3. For details, refer to the Image Setting section.
• Change the Startup Screen from the default setting Acer 
to User.
• Press Screen Capture to customize the startup screen.
• A dialog box appears to confirm the action. Choose Yes to 
use the current image as your customized startup screen. The 
capture range is the red rectangular area. Choose No to 
cancel the screen capture and exit the onscreen display (OSD).
• A message appears, stating that the screen capture is in 
progress.
• When the screen capture is finished, the message disappears 
and the original display is shown.
• The customized startup screen, as shown below, takes effect 
when there is a new input signal or when you restart the 
projector.
Note: This screen capture function is limited by 4:3 aspect ratio only.
Note: For XGA models, to get best quality for you desired image, suggest 
end-user set PC resolution to 1024 x 768 before you use this function.
Note: For SVGA models, to get best quality for you desired image, suggest 
end-user set PC resolution to 800 x 600 before you use this function. 
						

							21
EnglishLamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding Activate this function to display a reminder to change the lamp 30 
hours before its expected end-of-life.
Lamp Hour Reset
Press the   button after choosing Yes to turn the lamp hour 
counter to 0 hours.
Security Security
This projector provides a useful security function for the 
administrator to manage usage of the projector .
Press   to change the Security setting. If the security function 
is enabled, your must enter the Administrator Password first 
before changing the security settings.
•Select On to enable the security function. The user has to 
enter a password to operate the projector. Please refer to the 
User Password section for details.
•If Off is selected, then the user can turn on the projector 
without password.
Timeout(Min.)
Once Security is activated to On, the administrator can set 
timeout function.
•Press   or   to select the timeout interval.
•The range is from 10 minute to 990 minutes.
•When the time is up, the projector will prompt the user to 
enter the password again.
•The factory default setting of Timeout(Min.) is Off.
•Once the security function is enabled, the projector will 
request user to enter password when switch on the projector . 
Both User Password and Administrator Password can be 
accepted for this dialogue.
User password
•Press   to setup or change the User Password.
•Press number keys to set your password on the remote control 
and press MENU to confirm. 
•Press   to delete character.
•Enter the password when you see Confirm Password 
displayed.
•The password should be between 4 and 8 characters long.
•If you select Request password only after plugging power 
cord, the projector will prompt the user to enter the 
password every time the power cord is plugged.
•If you select Always request password while projector turns 
on, the user has to enter the password every time when the 
projector is turned on. 
						

							22
English
Audio setting
Administrator Password
The Administrator Password can be used in both the Enter 
Administrator Password and Enter Password dialog boxes.
•Press   to change the Administrator Password.
•The factory default of Administrator Password is 1234.
If you forgot your administrator password, do the following to 
retrieve the administrator password:
•An unique 6-digit Universal Password which is printed on 
the Security Card (please check accessory in the box). This 
unique password is the number which will be accepted by 
projector anytime no matter what the Administrator 
Password is.
•If losing this security card and number, please contact with an 
Acer service center.
Lock User Startup Screen
•Default Lock User Startup Screen is OFF. If lock user startup 
screen is ON, users cannot change startup screen anymore 
and avoid other users change that arbitrarily. Choose OFF 
to unlock startup screen.
Reset
•Press the button after choosing Yes to return the 
parameters on all menus to the factory default settings.
Volume
•Press   to decrease the volume.
•Press   to increase the volume.
Mute
•Choose On to mute the volume. •Choose Off to restore the volume. 
Power On/Off Volume
•Select this function to adjust the notification volume when 
turning the projector on/off.
Alarm Volume
•Select this function to adjust the volume of any warning 
notifications. 
						

							23
EnglishTimer setting
Language setting
Timer Start•Press   to start or stop the timer.
Timer Period
•Press   or   to adjust the timer period.
Timer Volume
•Select this function to adjust the notification volume when 
the timer function is enabled and time is up.
Timer Display
•Press   or   to which timer mode to display on the 
screen.
Timer Location
•Choose the location of the timer on the screen.
Language
Choose the multilingual OSD menu. Use the or key 
to select your preferred menu language.
•Press  to confirm the selection. 
						

							
24
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following 
troubleshooting guide. If the problem persists, please contact your local reseller 
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears  onscreen•Connected as described in  the Getting Started 
section.
•Ensure none of the connector pins are bent or 
broken.
•Check if the projector la mp has been securely 
installed. Please refer to the Replacing the Lamp 
section.
•Make sure you have slid on the lens door and the 
projector is turned on.
2 Partial, scrolling  or incorrectly 
displayed 
image(For PC 
(Windows 95/98/
2000/XP))
•Press RESYNC on the remote control or control panel.
•For an incorrectly displayed image:•Open My Computer, open the Control 
Panel, and then double-click the Display 
icon.
•Select the Settings tab.•Verify that your display resolution setting is 
lower than or equal to SXGA (1280 x 1024) 
(P1165) or SXGA+ (1400 x 1050) (P1265) or 
UXGA (1600 x 1200) (P5270 series).
•Click the Advanced Properties button.
If the problem still appears, change the monitor display 
you are using and follow the steps below:
•Verify that the resolution setting is lower than 
or equal to SXGA (1280 x 1024)(P1165) or  
SXGA+ (1400 x 1050)(P1265) or UXGA (1600 x 
1200) (P5270 series).
•Click the Change button under the 
Monitor tab.
•Click Show all devices. Next, select Standard 
monitor types under th e SP  box, and choose 
the resolution mode you need under the 
Models box.
•Verify that the resolution setting of the 
monitor display is lower than or equal to SXGA 
(1280 x 1024)(P1165) or  SXGA+ (1400 x 
1050)(P1265) or UXGA (1600 x 1200) (P5270 
series). 
						

							
25
English3 Partial, scrolling or incorrectly 
displayed image
(For notebooks)•Press RESYNC on the remote control or control 
panel.
•For an incorrectly displayed image:•Follow the steps for item 2 (above) to adjust 
the resolution of your computer.
•Press the toggle output settings. Example: 
[Fn]+[F4],  Compaq  [Fn]+[F4],  Dell [Fn]+[F8] , 
Gateway [Fn]+[F4] , IBM [Fn]+[F7] , HP 
[Fn]+[F4] , NEC [Fn]+[F3] , Toshiba [Fn]+[F5 ]
•If you experience difficulty changing resolutions or 
your monitor freezes, restart all equipment 
including the projector.
4 The screen of the  notebook 
computer is not 
displaying your 
presentation
•If you are using a Microsoft® Windows® based 
notebook: Some notebook PCs may deactivate their 
own screens when a second display device is in use. 
Each has a different way to be reactivated. Refer to 
your computers manual for detailed information.
•If you are using an Apple® Mac® OS based 
notebook: In System Preferences, open Display and 
select Video Mirroring On.
5 Image is unstable  or flickering
•Adjust the Tracking to correct it. Refer to the 
Image Setting section for more information.
•Change the display color depth settings on your 
computer.
6 Image has vertical  flickering bar
•Use Frequency to make an adjustment. Refer to 
the Image Setting section for more information.
•Check and reconfigure the display mode of your 
graphics card to make it compatible with the 
projector.
7 Image is out of  focus
•Make sure the lens door is slid on.
•Adjusts the focus ring on the projector lens.
•Make sure the projection screen is within the 
required distance of 3.3 to 39.0 feet (1.0 to 
11.9meters) from the projector. Refer to the How 
to Get a Preferred Image Size by Adjusting Distance 
and Zoom section for more information.
8 Image is stretched  when displaying a 
widescreen 
DVD title When you play a DVD encoded in anamorphic or 16:9 
aspect ratio you may need to adjust the following 
settings:
•If you play an Letterbox(LBX) format DVD title, 
please change the format to Letterbox(LBX) in the 
projector OSD.
•If you play a 4:3 format DVD title, please change the 
format to 4:3 in the projector OSD.
•If the image is still stretched, you will also need to 
adjust the aspect ratio. Set up the display format to 
16:9 (wide) aspect ratio on your DVD player. 
						

							
26
English
Problems with the Projector
9 Image is too small or too large•Adjust the zoom lever on the top of the projector.
•Move the projector closer to or further from the 
screen.
•Press MENU on the remote control or on the 
control panel. Go to Image setting --> Aspect 
Ratio and try different settings.
10 Image has slanted  sides
•If possible, reposition the projector so that it is 
centered on the screen.
•Press the Keystone   /    button on the control 
panel or press the Keystone   /   /   /    on the 
remote control until the sides are vertical.
11 Image is reversed
•Select Image --> Projection on the OSD and adjust 
the projection direction.
# Condition Solution
1 The projector stops responding  to all controls If possible, turn off the projector, then 
unplug the power cord and wait at least 30 
seconds before reconnecting power.
2 Lamp burns out or makes a  popping sound When the lamp reaches the end of its useful 
life, it will burn ou
t and may make a loud 
popping sound. If this happens, the projector 
will not turn on until the lamp module has 
been replaced. To replace the lamp, follow 
the procedures in the Replacing the Lamp 
section. 
						

							
27
EnglishOSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.Projector Overheated - the projector has exceeded its 
recommended operating temperature and must be allowed to 
cool down before it may be used.
Replace the lamp - the lamp is  about to reach its maximum 
lifetime. Prepare to replace it soon. 
						

							
28
English
LED & Alarm Definition Listing
LED Messages
MessageLamp LED Temp LED Power LED
Red Red Red Blue
Standby 
(power cord plugged in) -- -- V --
Lamp retry -- -- -- Quick  flashing
Turning off 
(cooling state) -- -- Quick 
flashing--
Turning off 
(cooling completed) -- -- V --
Error (thermal failure) -- -- -- V
Error (fan lock failure) -- Quick  flashing-- V
Error (lamp breakdown) V -- -- V
Error (color Wheel fail) Quick  flashing-- -- V