Acer Projector P1183 User Manual

31
English
Note: Functions vary depending on model definition. LANLAN
Default is Off. Choose On to enable LAN connection.
 If users want to do LAN control under standby mode, 
change VGA OUT (Standby) from Off to On.
LAN IP/Mask
Identify IP and Mask address.
LAN Reset
Reset LAN function. 

32
English
Management
Note: Functions vary depending on model definition. ECO Mode Choose On to dim the projector lamp which will lower power 
consumption, extend the lamp life and reduce noise. Choose Off 
to return normal mode.
High Altitude Choose On to turn on High Altitude mode. Operate the fans at 
full speed continuously to allow for proper high altitude cooling of 
the projector.
Turn Off Mode
•Instant Off: Shuts down the projector without fan cooling.
•Instant Resume: Resumes the system when the...

33
EnglishAudio
Note: Functions vary depending on model definition. Volume
•Press   to decrease the volume.
•Press   to increase the volume.
Mute
•Choose On to mute the volume. 
•Choose Off to restore the volume. 
Power On/Off Volume Select this function to adjust the notification volume when 
turning the projector on/off. 

34
English
3D
Note: It needs correct settings on graphic card 3D application program for 
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media 
Player can support 3D format files. You can download these three players 
on web page below,
- Stereoscopic Player (Trial): 
http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): 
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: 3D L/R Invert is only available when 3D is enabled....

35
EnglishAcer LAN webpage management
How to login in
Open browser and enter the Server IP address by 192.168.100.10 to find below 
homepage of acer LAN webpage management. A password is needed to login 
in before using.
Select a user. Administrator is with high authority that can process more 
operations such as network setting and alert setting. Default password of 
administrator is admin. And User is with normal authority with default 
password by user. Click Login button to enter into homepage with...

36
English
Home
Home page shows connection status and you can find three main functions 
listed, Control Panel, Networking Setting and Alert Setting.
Note: Control Panel and Networking Setting are only for Administrator 
account.
Control Panel
Enduser can control and adjust projector setting value via this page. 

37
EnglishNetwork Setting
Enduser can set IP address, group name and password as wish. After change 
network configurations or password, projector will reboot automatically after 
press Apply.
Note: Group Name and projector Name must be less then 32 characters.
Alert Setting
Enduser can send mail with error message right away if projector has problem. 

38
English
Logout
After tap Logout, you will return to login page within 5 seconds.
Note: Functions vary depending on model definition. 

39
EnglishAppendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following 
troubleshooting guide. If the problem persists, please contact your local reseller 
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears 
onscreen•Connected as described in the Getting Started 
section.
•Ensure none of the connector pins are bent or 
broken.
•Check if the projector lamp has been securely 
installed. Please refer to the Replacing the Lamp...

40
English
3 Partial, scrolling 
or incorrectly 
displayed image
(For notebooks)•Press RESYNC on the remote control.
•For an incorrectly displayed image:•Follow the steps for item 2 (above) to adjust 
the resolution of your computer.
•Press the toggle output settings. Example: 
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], 
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4], 
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•If you experience difficulty changing resolutions or 
your monitor freezes, restart all equipment...