Acer P1100 Dlp Users Guide

31
EnglishLanguage
Language
Choose the multilingual OSD menu. Use the   or   key to 
select your preferred menu language.
•Press   to confirm the selection.
Downloaded From projector-manual.com Acer Manuals 

32
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following 
troubleshooting guide. If the problem persists, please contact your local reseller 
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears 
onscreen•Connected as described in the Getting Started 
section.
•Ensure none of the connector pins are bent or 
broken.
•Check if the projector lamp has been securely 
installed. Please refer to the Replacing the Lamp...

33
English3 Partial, scrolling 
or incorrectly 
displayed image
(For notebooks)•Press RESYNC on the remote control or control 
panel.
•For an incorrectly displayed image:•Follow the steps for item 2 (above) to adjust 
the resolution of your computer.
•Press the toggle output settings. Example: 
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], 
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP 
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]
•If you experience difficulty changing resolutions or 
your monitor freezes, restart...

34
English
8 Image is stretched 
when displaying a 
widescreen 
DVD titleWhen you play a DVD encoded in anamorphic or 16:9 
aspect ratio you may need to adjust the following 
settings:
•If you play an Letterbox(LBX) format DVD title, 
please change the format to Letterbox(LBX) in the 
projector OSD.
•If you play a 4:3 format DVD title, please change the 
format to 4:3 in the projector OSD.
•If the image is still stretched, you will also need to 
adjust the aspect ratio. Set up the display format to 
16:9...

35
EnglishOSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its 
recommended operating temperature and must be allowed to 
cool down before it may be used.
Replace the lamp - the lamp is about to reach its maximum 
lifetime. Prepare to replace it soon.
Downloaded From projector-manual.com Acer Manuals 

36
English
Problems with the Projector
# Condition Solution
1 The projector stops responding 
to all controlsIf possible, turn off the projector, then 
unplug the power cord and wait at least 30 
seconds before reconnecting power.
2 Lamp burns out or makes a 
popping soundWhen the lamp reaches the end of its useful 
life, it will burn out and may make a loud 
popping sound. If this happens, the projector 
will not turn on until the lamp module has 
been replaced. To replace the lamp, follow 
the...

37
EnglishLED & Alarm Definition Listing
LED Messages
MessageLamp LED Temp LED Power LED
Red Red Red Blue
Standby 
(power cord plugged in)-- -- V --
Power button ON -- -- -- V
Lamp retry -- -- -- Quick 
flashing
Turning off 
(cooling state)-- -- Quick 
flashing--
Turning off 
(cooling completed)-- -- V --
Error (thermal failure) -- V -- V
Error (fan lock failure) -- Quick 
flashing-- V
Error (lamp breakdown) V -- -- V
Error (color Wheel fail) Quick 
flashing-- -- V
Downloaded From projector-manual.com...

38
English
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the 
lamp.
The projector will detect the lamp life. You will be shown a warning message 
Lamp is approaching the end of its useful life in full power operation. 
Replacement Suggested! When you see this message, change the lamp as soon 
as possible. Make sure the projector has been cooling down for at least 30 
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool...

39
EnglishCeiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the 
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and 
secure the mount base.
Note: Screws are not included. Please obtain the appropriate 
screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of four-cylinder screws.
20 mm13mm
8.4mm130 mm
49.9mm
Ceiling Mount Base    - Attach to ceiling
Screw Type A  50 mm length/8 mm...

40
English
3 Use the appropriate number of screws for the projector size to attach the 
projector to the ceiling mount bracket.
Note: It is recommended that you keep a reasonable space 
between the bracket and the projector to allow for proper heat 
distribution. Use two washers for extra support, if deemed 
necessary.
4 Attach the ceiling bracket to the ceiling rod.
Scr ew  T ype B
Smaller Washer
Large Washer
Projector Bracket
Supports projector and allows -   
  for adjustments     
Spa cer
    - For...