Acer Extensa 5610 Service Guide

							Chapter 251
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
New versions of system programs
New features or options
Restore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not 
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
completely loaded. 
Fellow the steps below to run the Phlash.
1.Prepare a bootable diskette.
2.Copy the flash utilities to the bootable diskette.
3.Then boot the system from the bootable diskette. The flash utility has auto-execution function.
SG_Dallen.book  Page 51  Thursday, April 19, 2007  11:08 AM 
						

							52Chapter 2
Remove HDD/BIOS Utility
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
If you key in wrong HDD password for three time, “HDD password error code” would display on the 
screen. See the image below.
If you need to solve HDD password locked problem, you can run HDD_PW.EXE
1.
Key in “hdd_pw 15494 0”
2.Select “2”
3.Choose one upper-case string
Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password.
SG_Dallen.book  Page 52  Thursday, April 19, 2007  11:08 AM 
						

							Chapter 253
Remove BIOS Password:
If you key in wrong Supervisor Password for three time, “System Disabled” would display on the 
screen. See the image below.
SG_Dallen.book  Page 53  Thursday, April 19, 2007  11:08 AM 
						

							54Chapter 2
If you need to solve BIOS password locked problem, you can run BIOS_PW.EXE
1.
Key in “bios_pw 14452 0”
2.Choose one upper-case string
Reboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password.
SG_Dallen.book  Page 54  Thursday, April 19, 2007  11:08 AM 
						

							Chapter 255
SG_Dallen.book  Page 55  Thursday, April 19, 2007  11:08 AM 
						

							56Chapter 2
SG_Dallen.book  Page 56  Thursday, April 19, 2007  11:08 AM 
						

							Chapter 357
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
Wrist grounding strap and conductive mat for preventing electrostatic discharge
Flat screwdriver
Philips screwdriver
Hex screwdriver
Plastic flat screwdriver
Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the 
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3
Machine Disassembly and Replacement
SG_Dallen.book  Page 57  Thursday, April 19, 2007  11:08 AM 
						

							58Chapter 3
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system. 
3.Place the system on a flat, stable surface. 
4.Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
 External module disassembly
 Main unit disassembly
 LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. 
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you 
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly 
frame in that order. 
Main Screw List
ItemScrewColorPart No.
A M2.5 x L6 Black 86.00E33.736
B M2 x L4 Black 86.00A02.140
C M2 x L4 Silver 86.9A552.4R0
D M2.5 x L5 Silver 86.00E74.335
E M2.5 x L5 Black 86.00F87.735
F M2 x L3 Silver 86.00C07.220
G M2.5 x L6 Silver 86.9A544.4R0
H M2.5 x L8 Black 86.00E34.738
SG_Dallen.book  Page 58  Thursday, April 19, 2007  11:08 AM 
						

							Chapter 359
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you 
on the components that need to be removed during servicing. For example, if you want to remove the main 
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Screw List
ScrewPart No.
A M2.5 x L6 86.00E33.736
B M2 x L4 86.00A02.140
C M2 x L4 86.9A552.4R0
F M2 x L3 86.00C07.220
EXTERNAL MODULE DISASSEMBLY
WLAN
BOARDTURN OFF POWER
AND PERIPHERALS
UNPLUG POWER
CABLES
Fx2
LOWER
COVER Bx7
DIMM
MODULES
OPTICAL DISK
DRIVE MODULEAx1
OPTICAL DISK
DRIVECx1OPTICAL
LOCKER
BRACKET
HDD
MODULE
HARD DISK
RUBBER
ENCLOSUREHARD DISK
DRIVE
SG_Dallen.book  Page 59  Thursday, April 19, 2007  11:08 AM 
						

							60Chapter 3
Removing the Battery Pack
1.Turn base unit over. 
2.Slide the battery lock/unlock latch to the unlock position (1). 
3.Slide and hold the battery release latch to the release position (2), then remove the battery from the main 
unit (3). 
Removing the SD dummy card
1.Push the SD dummy card all the way in to eject it (1, 2).
SG_Dallen.book  Page 60  Thursday, April 19, 2007  11:08 AM