Acer Extensa 2500 Service Guide

Chapter 352
Removing the Wireless LAN Board and the Modem Board
1.See “Removing the Battery” on page 50.
2.To remove the wireless LAN board, first remove the two screws holding the modem cover. 
3.Remove the modem cover from the machine.
4.Disconnect the wireless antennae.
5.Pop out the wireless LAN board.
6.To remove the modem board, first remove the two screws fastening the modem board. 
7.Detach the modem board and disconnect the modem cable carefully, then remove the modem board.  

53Chapter 3
Removing the Hard Disk Drive Module
1.See “Removing the Battery” on page 50.
2.To remove the hard disk drive, pull the hard disk dirve carefully.
3.Then take the hard disk drive out of the main unit.
Disassembling the Hard Disk Drive Module
1.See “Removing the Battery” on page 50.
2.See “Removing the LCD Module” on page 54.
3.Remove the two screws that fasten the HDD holder.
4.Detach the hard disk drive from the HDD holder. 

Chapter 354
Removing the LCD Module
Removing the Middle Cover
1.See “Removing the Battery” on page 50.
2.To remove the middle cover, first use a plastic flat screwdriver to remove the right hinge cap.
3.Remove the screw that secures the middle cover.
4.Remove the left hinge cap.
5.Then remove the screw holding the middle cover on the other side.
6.Detach the middle cover from the machine.
7.Disconnect the launch board cable then remove the middle cover off the main unit.
.
Removing the Launch Board
1.See...

55Chapter 3
3.Remove the two screws and then detach the launch board from the middle cover.
Removing the LCD Module
1.See “Removing the Battery” on page 50.
2.See “Removing the Middle Cover” on page 54.
3.See “Removing the Launch Board” on page 54.
4.Remove the screw that fastens the LCD coaxial cable and disconnect the cable. Then disconnect the 
LCD inverter cable.
 
5.Remove the four screws holding the LCD hinge; two on the right and two on the left.Remove the four 
screws holding the LCD hinge; two...

Chapter 356 

57Chapter 3
Disassembling the LCD Module
Removing the LCD Bezel
1.See “Removing the Battery” on page 50.
2.See “Removing the Middle Cover” on page 54.
3.See “Removing the Launch Board” on page 54.
4.See “Removing the LCD Module” on page 55.
5.Use plastic tweezers to remove the four screw pads, and then remove the four screws that fasten the LCD 
bezel.
6.Snap off the bezel carefully, and then remove the LCD bezel from the LCD module.
Removing the Inverter Board (15” LCD)
1.See “Removing the Battery” on...

Chapter 358
NOTE: Please arrange the LCD inverter cable well to the LCD panel as the picture below shows when you 
reassemble the LCD module.
Removing the 15” TFT LCD
1.See “Removing the Battery” on page 50.
2.See “Removing the Middle Cover” on page 54.
3.See “Removing the Launch Board” on page 54.
4.See “Removing the LCD Module” on page 55.
5.See “Removing the LCD Bezel” on page 57.
6.See “Removing the Inverter Board (15” LCD)” on page 57.
7.To remove the LCD, first remove the four screws that secure...

59Chapter 3
2.See “Removing the Middle Cover” on page 54.
3.See “Removing the Launch Board” on page 54.
4.See “Removing the LCD Module” on page 55.
5.See “Removing the LCD Bezel” on page 57.
6.See “Removing the Inverter Board (15” LCD)” on page 57.
7.See “Removing the 15” TFT LCD” on page 58.
8.Remove the four screws holding the right LCD bracket.Then remove the right bracket.
9.Remove the four screws holding the left LCD bracket. Then remove the left bracket..
Removing the LCD Coaxial Cable
1.See...

Chapter 360
2.See “Removing the Middle Cover” on page 54.
3.See “Removing the Launch Board” on page 54.
4.See “Removing the LCD Module” on page 55.
5.See “Removing the LCD Bezel” on page 57.
6.See “Removing the Inverter Board (15” LCD)” on page 57.
7.See “Removing the 15” TFT LCD” on page 58.
8.Remove the screw holding the right hinge, then remove the right hinge.
9.Remove the screw holding the left hinge, then remove the left hinge. 

61Chapter 3
Disassembling the Main Unit
Removing the Keyboard
1.See “Removing the Battery” on page 50.
2.See “Removing the Middle Cover” on page 54.
3.To remove the keyboard, carefully pull the keyboard out and upwards as the pticute shows.
 
4.Use a plastic tweezers or a plastic flat screwdriver to disconnect the keyboard cable from the main board 
carefully, then remove the keyboard.
Removing the RTC Battery
1.See “Removing the Battery” on page 50.
2.See “Removing the Middle Cover” on page 54.
3.See...