Acer Extensa 2000 Service Guide

Chapter 242
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following 
message. 

43Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay. 

Chapter 244
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS. 

45Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
TNew versions of system programs
TNew features or options
TRestore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please...

Chapter 346
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
TWrist grounding strap and conductive mat for preventing electrostatic discharge
TFlat-bladed screw driver
TPhillips screw driver
TTw e e z e r s
TPlastic Flat-bladed screw driver
THexed Screw Driver
NOTE: The screws for the different components vary in size. During the disassembly process, group the 
screws...

47Chapter 3
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system. 

Chapter 348
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.
Start
Battery
HDD ModuleHinge Caps
HDD
LCD ModuleF*6Keyboard
Lower Case
Assembly
J*5
F*10
D*4
DIMM Cover
Memory*2
J*2
Launch Board...

49Chapter 3
Screw List
ItemDescription
A SCW HEX NYL I#R-40/O#4-40 L5.5(34.00015.081)
B SCRW MACH PAN NYLOK M2.0*10 NI 
(86.1A522.100)
C SCRW CPU SCREW FORCE 5KGS(86.T30V1.001)
D SCREW M2*3 NYLON 1JMCPC-
420325(86.9A352.3R0)
E SCREW M2.5X6(86.9A353.6R0)
F SRW M2.5*8L B/ZN NYLOK 700(86.9A353.8R0)
G SCREW M3x4(86.9A524.4R0)
H SCREW M2X2.0(86.9A552.2R0)
I SCREW WAFER NYLOK NI 2ML3(86.9A552.3R0)
J SCRW M2*4 WAFER NI(86.9A552.4R0)
K SCRW M2.5*3 WAFER NI(86.9A553.3R0)
L SCREW M2.5*4L NI(86.9A553.4R0)
4 LCD...

Chapter 350
Removing the Battery
1.To remove the battery, push the battery release latch.
2.Then slide the battery out from the machine. 

51Chapter 3
Removing the Memory Module
1.See “Removing the Battery” on page 50.
2.To remove the memory module from the machine, first remove the two screws holding the dimm cover.
3.Remove the dimm cover.
4.Pop up the memory.
5.Then remove the memory.