Acer Aspire X3300 User Guide

							
9
English
EnglishRegulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B 
digital device pursuant to Part 15 of the  FCC rules. These limits are designed to 
provide reasonable protection against  harmful interference in a residential 
installation. This device generates, uses , and can radiate radio frequency energy 
and, if not installed and used in acco rdance with the instructions, may cause 
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular 
installation. If this device does cause ha rmful interference to radio or television 
reception, which can be determined by turning the device off and on, the 
user is encouraged to try to correct th e interference by one or more of the 
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a  circuit different from that to which 
the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables 
to maintain compliance with FCC regulations. In compliance with FCC 
regulations, use shielded cables to conn ect to other computing devices. A dual-
link cable is recommended for DVI output.
Notice: Peripheral devices
Only peripherals (input/output devices,  terminals, printers, etc.) certified to 
comply with the Class B limits may be a ttached to this equipment. Operation 
with non-certified peripherals is likely to  result in interference to radio and TV 
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could 
void the users authority, which is granted by the Federal Communications 
Commission, to operate this computer. 
						

							
10
English
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) this device  may not cause harmful interference, 
and (2) this device must accept any interference received, including interference 
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque à lintention des  utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du 
Canada.
Declaration of Conformity for EU countries
Hereby, Acer, declares that this PC series is in compliance with the essential 
requirements and other relevant provisions of Directive 1999/5/EC. (Please visit 
http://global.acer.com/support/certificate.htm  for complete documents.)
Compliant with Russian regulatory certification
Modem notices
Notice for USA
This equipment complies with Part 68 of  the FCC rules. Located on the modem is 
a label that contains, among other info rmation, the FCC Registration Number 
and Ringer Equivalence Number (REN) for this equipment. Upon request, you 
must provide this information to your telephone company.
If your telephone equipment causes harm to the telephone network, the 
telephone company may discontinue your  service temporarily. If possible, they 
will notify you in advance. But, if advance notice is not practical, you will be 
notified as soon as possible. You will also be informed of your right to file a 
complaint with the FCC. 
						

							
11
English
EnglishYour telephone company may make changes in its facilities, equipment, 
operations, or procedures that could affect the proper functioning of your 
equipment. If they do, you will be notified in advance to give you an 
opportunity to maintain unin terrupted telephone service.
If this equipment should fail to operate properly, disconnect the equipment 
from the phone line to determine if it is causing the problem. If the problem is 
with the equipment, discontinue use and contact your dealer or vendor.
Caution:  To reduce the risk of fire, use only No. 26 AWG or larger 
UL Listed or CSA Certified Telecommunication Line Cord.
TBR 21
This equipment has been approved [Council Decision 98/482/EC - TBR 21] for 
single terminal connection to the Public Switched Telephone Network (PSTN). 
However, due to differences between the  individual PSTNs provided in different 
countries, the approval does not, of itself, give an unconditional assurance of 
successful operation on every PSTN terminat ion point. In the event of problems, 
you should contact your equipment  supplier in the first instance.
List of applicable countries
EU member states as of May 2004 are: Belgium, Denmark, Germany, Greece, 
Spain, France, Ireland, Italy, Luxembourg, the Netherlands, Austria, Portugal, 
Finland, Sweden, United Kingdom Estonia, Latvia, Lithuania, Poland, Hungary, 
Czech Republic, Slovak Republic, Slovenia, Cyprus and Malta. Usage allowed in 
the countries of European Union, as well as Norway, Switzerland, Iceland and 
Liechtenstein. This device must be used  in strict accordance with the regulations 
and constraints in the country of use.  For further information, please contact 
local office in the country of use.
Notice for Australia
For safety reasons, only connect  headsets with a telecommunications 
compliance label. This includes customer equipment previously labelled 
permitted or certified. 
						

							
12
English
Notice for New Zealand
1 The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum 
conditions for connection to its netw ork. It indicates no endorsement of 
the product by Telecom, nor does it provide any sort of warranty. Above 
all, it provides no assurance that any  item will work correctly in all respects 
with another item of Telepermitted equipment of a different make or 
model, nor does it imply that any product is compatible with all of 
Telecoms network services.
2 This equipment is not capable, under all operating conditions, of correct  operation at the higher speeds for which it is designed. Telecom will accept 
no responsibility should difficulties arise in such circumstances.
3 Some parameters required for comp liance with Telecoms Telepermit 
requirements are dependent on the equipment (PC) associated with this 
device. The associated equipment shall be set to operate within the 
following limits for compliance with Telecoms Specifications:
a There shall be no more than 10  call attempts to the same number 
within any 30 minute period for any single manual call initiation, and
b The equipment shall go on-hook for a period of not less than 30  seconds between the end of one attempt and the beginning of the 
next call attempt.
4 Some parameters required for comp liance with Telecoms Telepermit 
requirements are dependent on the equipment (PC) associated with this 
device. In order to operate within th e limits for compliance with Telecoms 
specifications, the associated equipment shall be set to ensure that 
automatic calls to different numbers ar e spaced such that there is not less 
than 5 seconds between the end of  one call attempt and the beginning 
of another.
5 This equipment shall not be set up to make automatic calls to Telecoms  111 Emergency Service.
6 This device is equipped with pulse dialing while the Telecom standard is  DTMF tone dialing. There is no guarantee that Telecom lines will always 
continue to support pulse dialing.
7 Use of pulse dialing, when this equipment is connected to the same line as  other equipment, may give rise to bell tinkle or noise and may also cause a 
false answer condition. Should such problems occur, the user should NOT 
contact the telecom Fault Service.
8 This equipment may not provide for the effective hand-over of a call to  another device connected to the same line.
9 Under power failure conditions this appliance may not operate. Please  ensure that a separate telephone,  not dependent on local power, is 
available for emergency use. 
						

							
13
English
EnglishLaser compliance statement
The CD or DVD drive used with this computer is a laser product. 
The CD or DVD drives classification label (shown below) is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION: INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE 
TO BEAM.
APPAREIL A LASER DE CLASSE 1 PRODUIT
LASERATTENTION: RADIATION DU FAISCEAU LASER INVISIBLE EN CAS 
D’OUVERTURE. EVITTER TOUTE EXPOSITION AUX RAYONS.
LUOKAN 1 LASERLAITE LASER KLASSE 1
VORSICHT: UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET 
NICHT DEM STRAHLL AUSSETZEN
PRODUCTO LÁSER DE LA CLASE I
ADVERTENCIA: RADIACIÓN LÁSER INVISIBLE AL SER ABIERTO. EVITE EXPONERSE 
A LOS RAYOS.
ADVARSEL: LASERSTRÅLING VEDÅBNING SE IKKE IND I STRÅLEN.
VARO! LAVATTAESSA OLET ALTTINA LASERSÅTEILYLLE.
VARNING: LASERSTRÅLNING NÅR DENNA DEL ÅR ÖPPNAD ÅLÅ TUIJOTA 
SÅTEESEENSTIRRA EJ IN I STRÅLEN
VARNING: LASERSTRÅLNING NAR DENNA DEL ÅR ÖPPNADSTIRRA EJ IN I 
STRÅLEN
ADVARSEL: LASERSTRÅLING NAR DEKSEL ÅPNESSTIRR IKKE INN I STRÅLEN
Digital audio output statement
The optical connector contains no laser or light emitting diode (LED) more than 
Class I.
Macrovision copyright protection notice
U.S Patent Nos. 4,631,603; 4,819,098; 4,907,093; 5,315,448; and 6,516,132.
This product incorporates copyright protection technology that is protected by 
U.S. patents and other intellectual property rights. Use of this copyright 
protection technology must be authorized by Macrovision, and is intended for 
home and other limited viewing uses only unless otherwise authorized by 
Macrovision. Reverse engineering or disassembly is prohibited.
Radio device regulatory notice
Note : Below regulatory information is for models with wireless 
LAN and/or Bluetooth only. 
						

							
14
English
General
This product complies with the radio frequency and safety standards of any 
country or region in which it has been approved for wireless use. Depending on 
configurations, this product may or may not contain wireless radio devices (such 
as wireless LAN and/or Bluetooth module s). Below information is for products 
with such devices.
European Union (EU)
R&TTE Directive 1999/5/EC as attested by conformity with the following 
harmonized standard: 
• Article 3.1(a) Health and Safety
•
EN60950-1:2001 + A11:2004
•EN50371:2002
•Article 3.1(b) EMC
•
EN301 489-1 V1.6.1
•EN301 489-3 V1.4.1 (Applicable to non-bluetooth wireless 
keyboard mouse set)
•EN301 489-17 V1.2.1 
•Article 3.2 Spectrum Usages
•
EN300 440-2 V1.1.2 (Applicable to non-bluetooth wireless 
keyboard mouse set).
•EN300 328 V1.7.1
•EN301 893 V1.4.1 (Applicable  to 5GHz high performance 
RLAN)
List of applicable countries
EU member states as of May 2004 are: Belgium, Denmark, Germany, Greece, 
Spain, France, Ireland, Italy, Luxemb ourg, the Netherlands, Austria, Portugal, 
Finland, Sweden, United Kingdom, Estonia, Latvia, Lithuania, Poland, Hungary, 
Czech Republic, Slovak Republic, Slovenia, Cyprus and Malta. Usage allowed in 
the countries of the  European Union, as well as Norway, Switzerland, Iceland 
and Liechtenstein. This device must be  used in strict accordance with the 
regulations and constraints of the country  of use. For further information, 
please contact the local office in the country of use. 
						

							
15
English
EnglishThe FCC RF safety requirement
The radiated output power of the wireless LAN Card and Bluetooth card is far 
below the FCC radio frequency exposure limi ts. Nevertheless, the PC series shall 
be used in such a manner that the po tential for human contact during normal 
operation is minimized as follows:
1 This device is restricted to indoor us e due to its operation in the 5.15 to 
5.25 GHz frequency range. FCC requires this product to be used indoors for 
the frequency range 5.15 to 5.25 GHz  to reduce the potential for harmful 
interference to co-channel Mobile Satellite systems.
2 High power radar are allocated as primary users of the 5.25 to 5.35 GHz  and 5.65 to 5.85 GHz bands. These radar stations can cause interference 
with and/or damage this device.
3 An improper installation or unauthorized use may cause harmful  interference to radio communications.  Also any tampering of the internal 
antenna will void the FCC certification and your warranty.
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a Common information Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference 
that may cause undesired operation of the device.
b Operation in 2.4 GHz band To prevent radio interference to the  licensed service, this device is 
intended to be operated indoors an d installation outdoors is subject 
to licensing.
c Operation in 5 GHz band
Federal Communications Comission
Declaration of Conformity
This device complies with Part 15 of the  FCC Rules. Operation is subject to the 
following two conditions: (1) this device  may not cause harmful interference, 
and (2) this device must accept any interference received, including interference 
that may cause undesired operation.
The following local Manufacturer /Importe r is responsible for this declaration:
Product: Personal Computer
Model number: AcerSystem 
Name of responsible party: Acer America Corporation 
						

							
16
English
         Declaration of Conformity  
We , 
       Acer Incorporated
        8F, 88, Sec. 1, Hsin Tai Wu Rd., Hsichih, Taipei Hsien 221, Taiwan
Contact Person: Mr. Easy Lai
Tel: 886-2-8691-3089 Fax: 886-2-8691-3120
E-mail: [email protected]
Hereby declare that:
Product:  Personal Computer
Trade Name: Acer
Model Number: AcerSystem
Is compliant with the essential requirements and other relevant provisions of 
the following EC directives, and that all the necessary steps have been taken 
and are in force to assure that production units of the same product will 
continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following 
harmonized standards:
• EN55022: 2006, AS/NZS CISPR22: 2006, Class B
• EN55024: 1998 + A1: 2001 + A2:2003
• EN55013:2001 + A1:2003 + A2:2006 (Applicable to product built with TV 
tuner module)
• EN55020:2007 (Applicable to product built with TV tuner module)
• EN61000-3-2: 2006, Class D
• EN61000-3-3: 1995 + A1: 2001+A2: 2005
Low Voltage Directive 2006/95/EC as attested by conformity with the following 
harmonized standard:
• EN60950-1: 2001 + A11: 2004
• EN60065: 2002 + A1: 2006 (Applicable to product built with TV tuner 
module)
Council Decision 98/482/EC (CTR21) for pan- European single terminal 
connection to the Public Switched Telephone Network (PSTN). 
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous 
Substances in Electrical and Electronic Equipment .
The standards listed below are applied to the product if built with WLAN 
module or wireless keyboard and mouse.
Address of responsible party: 333 West San Carlos St. San Jose, CA 95110
U. S. A.
Contact person: Acer Representative
Tel: 254-298-4000
Fax: 254-298-4147 
						

							
17
English
EnglishR&TTE Directive 1999/5/EC as attested by conformity with the following 
harmonized standard: 
•  Article 3.1(a) Health and Safety
•EN60950-1:2001 + A11:2004
• EN50371:2002
•   Article 3.1(b) EMC
•EN301 489-1 V1.6.1
• EN301 489-3 V1.4.1 (Applicable to non-bluetooth wireless keyboard 
mouse set).
• EN301 489-17 V1.2.1 
•   Article 3.2 Spectrum Usages
•EN300 440-2 V1.1.2 (Applicable to non-bluetooth wireless keyboard 
mouse set).
• EN300 328 V1.7.1
• EN301 893 V1.4.1 (Applicable to 5GHz high performance RLAN).
Year to begin affixing CE marking 2009.
 
Easy Lai, Manager                                                                 Date 
Feb.9. 2009
                                                                                           
     Regulation Center, Acer Inc.
                                                              
Remark:  All images are for reference purposes only.
Actual configuration may vary.
V09A1 
						

							
18
English