Acer Aspire One Model Ao752 Service Guide

							Chapter 341
 LCD Module Disassembly Process
LCD Module Disassembly Flowchart
Screw List
StepScrewQuantityColorPart No.
LCD Bezel M2*5 (NL) 6 Black 86.TG607.004
LCD Module M2*5 (NL) 4 Black 86.TG607.004
LCD Panel M2*4 (NL) 5 Black 86.W0107.003
LCD Brackets M2*3 (NL) 4 Black 86.TG607.004 
						

							42Chapter 3
Removing the LCD Module
1.Remove the Upper Cover. See “Removing the Upper and Lower Covers” on page 39.
2.Disconnect the LCD cable from its connector
3.Disconnect and remove the antenna cables from the housing well.
NOTE: Main cable is black. The Auxiliary cable is white. 
						

							Chapter 343
4.Remove the four securing screws from the hinges.
5.Tilt the LCD module so it sits at a 90 degree angle.
IMPORTANT:Ensure all cables are clear of the lower cover before removing the LCD module.
6.Grasp the module by both sides and lift upwards.
StepSizeQuantityScrew Type
LCD Module M2*5 (NL) 4 
						

							44Chapter 3
Removing the LCD Bezel
1.Remove the LCD Module. See “Removing the LCD Module” on page 42.
2.Remove the four round and the two semi-rectangular screw caps.
3.Remove the six (6) securing screws.
4.Starting from the inside edges, pry the inside of the bezel upwards from the panel. Continue moving left until 
the bezel is removed. If necessary, use a plastic pry to release the corners of the bezel.
5. Lift up the bezel and remove it from the LCD Module.
StepSizeQuantityScrew Type
LCD Bezel M2*5 (NL) 6 
						

							Chapter 345
Removing the Camera Board
1.Remove the LCD Bezel. See “Removing the LCD Bezel” on page 44.
2.Disconnect the Camera Module cable from its connector as shown.
3.Remove the camera board from the LCD cover. 
						

							46Chapter 3
Removing the MIC Board
1.Remove the LCD Bezel. See “Removing the LCD Bezel” on page 44.
2.Disconnect the MIC cable from its connector as shown.
3.Remove the MIC board from the LCD cover. 
						

							Chapter 347
Removing the LCD Panel
1.Remove the LCD Bezel. See “Removing the LCD Bezel” on page 44.
2.Disconnect the MIC cable. See “Removing the MIC Board” on page 46.
3.Remove the five (5) securing screws from the LCD Module.
4.Grasp the left hinge and pivot down before pulling up. 
5.Remove it from its housing well.
StepSizeQuantityScrew Type
LCD Panel M2*4 (NL) 5 
						

							48Chapter 3
6.Hold the LCD Panel from the sides and lift to remove. Place it on a clean surface.
Removing the LCD Brackets and FPC Cable
1.Remove the LCD Panel. See “Removing the LCD Panel” on page 47.
2.Turn the LCD panel over on a clean surface. Remove the adhesive strips securing the LCD cable.
3.Disconnect the LCD cable from its connector as shown. 
						

							Chapter 349
4.Remove the four securing screws (two each side) from the LCD Panel brackets.
NOTE: The brackets are paired diagonally and marked as shown below.
StepSizeQuantityScrew Type
LCD Brackets M2*3 NL 4 
						

							50Chapter 3
Main Unit Disassembly Process
Main Unit Disassembly Flowchart
Screw List
StepScrewQuantityColorPart No.
WLAN M2*3 (NL) 1 Black 86.S0207.001
USB/LED/Power 
Board (HDD SKU)M2*3 (NL) 3 Black 86.S0207.001
USB/LED/Power 
Board (SSD SKU)M2*3 (NL) 4 Black 86.S0207.001
SSD Module M2*3 2 Black 86.S0207.001
Mainboard M2*3 1 Black 86.S0207.001
Speaker Module M2*3 4 Black 86.S0207.001
HDD Module M2.5*4 2 Black 86.D01V7.001
HDD Carrier M3*3.5 4 Black 86.TDY07.003
Thermal Module M2*3 3 Black 86.S0207.001