Acer Aspire 7740 Service Guide

Chapter 223
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if 
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press  to enter Setup” message is prompted 
on the...

24Chapter 2
Navigating the BIOS Utility
There are five menu options: Information, Main, Security, Boot, and Exit.
Follow these instructions:
•To choose a menu, use the left and right arrow keys.
•To choose an item, use the up and down arrow keys.
•To change the value of a parameter, press F5 or F6.
•A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
•Press Esc while you are in any of the menu options to go to the Exit menu.
•In any menu, you can load default settings by...

Chapter 225
Information
The Information screen displays a summary of your computer hardware information.
NOTE: The system information is subject to different models.
ParameterDescription
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
IDE0 Model Name This field shows the model name of HDD installed on primary IDE master.
IDE0 Serial Number This field displays the serial number of HDD installed on primary IDE master.
IDE1 Model Name This...

26Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option 
and recovery.
NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is 
because the user is not allowed to control the...

Chapter 227
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized 
use.
NOTE: Please refer to “Remove HDD/BIOS Password” section if you need to know how to remove HDD/BIOS 
Password.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget...

28Chapter 2
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the up/down keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because...

Chapter 229
2.Type the current password in the Enter Current Password field and press Enter.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following....

30Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.     

Chapter 231
Exit
The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the 
BIOS Setup Utility.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save...

32Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
•New versions of system programs
•New features or options
•Restore a BIOS when it becomes corrupted. 
Use the Flash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery disk at hand, then you should create a Crisis Disk (See “Steps for 
BIOS Recovery by Crisis Disk” on page 108) before you use the Flash utility.
NOTE: Do not install memory-related drivers (XMS, EMS,...