Acer Aspire 5930 Service Guide
Have a look at the manual Acer Aspire 5930 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 371 Main Unit Disassembly Process Main Unit Disassembly Flowchart Screw List ItemScrewColorPart No. A M2 x L4 Black 86.00E13.524 B M2.5 x L6 Black 86.00E12.536 E M2.5 x L10 Black 86.00F84.73A MAIN UNIT KEYBOARD MAIN BOARD Ax1 MAIN UNIT DISASSEMBLY LCD MODULE Ax 2 Bx2, Ex2 UPPER CASE Bx13,Ax3 MEDIA BOARD CPU/VGA THERMAL MODULE CPU SCREWX5(CPU) Ax1 BLUETOOTH MODULEAUDIO BOARD MODULE HEAT SINK FAN TOUCHPAD BRACKET MIDDLE COVER VGA CARD SCREWX4(VGA) Ax 2 POWER BOARD Ax 3 E-KEY BOARDSPEAKER MODULE Ax 4Ax 4 Ax 2 LAUNCH BOARD TOUCHPAD MODULEFINGERPRINT MODULEUSB MODULESUBWOOFER MODULE
72Chapter 3 Removing the Keyboard 1.See “Removing the Battery Pack” on page 60. 2.Push down on the lock and release the latches securing the keyboard to the upper case. 3.Carefully pry loose the keyboard and turn it over on the touchpad area.
Chapter 373 4.Disconnect the keyboard cable from the main board to remove the keyboard. Removing the Middle Cover 1.See “Removing the Battery Pack” on page 60. 2.Use a plastic screw driver to pry loose the side of the middle cover.
74Chapter 3 3.Carefully pry loose the middle cover from the latches securing it and remove the middle cover. Removing the Power Board 1.See “Removing the Battery Pack” on page 60. 2.See “Removing the Middle Cover” on page 73.. 3.Disconnect the cable from the Power Board connector.
Chapter 375 4.Remove the one screw (A) securing the Power Board to the upper case. 5.Release the Power Board from the latches and remove the Power Board from the upper case. Removing the Heatsink Fan Module 1.See “Removing the Battery Pack” on page 60. 2.See “Removing the Lower Cover” on page 62. 3.Remove the two screws (A) securing the heatsink fan module in place. StepSize (Quantity)ColorTo r q u e 1 M2 x L4 (1) Black 1.6 kgf-cm StepSize (Quantity)ColorTo r q u e 1~2 M2 x L4 (2) Black 1.6 kgf-cm
76Chapter 3 4.Lift the heatsink fan module and disconnect the heatsink fan connector from the main board. 5.Carefully lift up the heatsink fan module. Removing the CPU and VGA Heatsink Module 1.See “Removing the Battery Pack” on page 60. 2.See “Removing the Lower Cover” on page 62. 3.See “Removing the Heatsink Fan Module” on page 75. 4.Remove the four screws securing the VGA board heatsink module (Discrete Model only) and the five screw securing the CPU heatsink module.
Chapter 377 5.Carefully remove the heatsink module from the system. Removing the CPU 1.See “Removing the Battery Pack” on page 60. 2.See “Removing the Lower Cover” on page 62. 3.See “Removing the Heatsink Fan Module” on page 75. 4.See “Removing the CPU and VGA Heatsink Module” on page 76. 5.Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU.
78Chapter 3 6.Lift up carefully to remove the CPU. NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown. Removing the VGA Board (Discrete Model only) 1.See “Removing the Battery Pack” on page 60. 2.See “Removing the Lower Cover” on page 62. 3.See “Removing the Heatsink Fan Module” on page 75. 4.See “Removing the CPU and VGA Heatsink Module” on page 76. 5.Remove the two screws (A) securing the VGA board to the main board. StepSize (Quantity)ColorTo r q u e 1~2 M2 x L4 (2) Black 1.6 kgf-cm
Chapter 379 6.Remove the VGA board from the main board. Removing the LCD Module 1.See “Removing the Battery Pack” on page 60. 2.See “Removing the SD dummy card” on page 61. 3.See “Removing the ExpressCard dummy card” on page 61. 4.See “Removing the Lower Cover” on page 62. 5.See “Removing the DIMM” on page 63. 6.See “Removing the WLAN Board Modules” on page 63. 7.See “Removing the TV Tuner Board Modules” on page 64. 8.See “Removing the Hard Disk Drive Module” on page 66. 9.See “Removing the Keyboard” on page 72. 10.See “Removing the Middle Cover” on page 73. 11 .Turn over the system and remove the two screws (B) from the bottom of the left and right hinges. StepSize (Quantity)ColorTo r q u e 1~2 M2.5 x L6 (2) Black 3.0 kgf-cm
80Chapter 3 12.Carefully pull out the wireless antenna cables from the hole and release the cables from the latches. 13.Disconnect the LCD cable connector from the main board. 14.Remove the two screws (E) from the left and right hinge of the LCD module. StepSize (Quantity)ColorTo r q u e 1~2 M2.5 x L10 (2) Black 4.0 kgf-cm