Acer Aspire 5740d Service Guide

							Chapter 223
Information
The Information screen displays a summary of your computer hardware information.
NOTE: The system information is subject to different models.
ParameterDescription
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
IDE0 Model Name This field shows the model name of HDD installed on primary IDE master.
IDE1 Model Name This field shows the model name of HDD installed on secondary IDE master.
ATAPI Model Name This field shows the model name of the Optical device installed in the system.
System BIOS Version Displays system BIOS version.
VGA BIOS Version This field displays the VGA firmware version of the system.
KBC Ver This field shows the keyboard 
Serial Number This field displays the serial number of this unit.
Asset Tag Number This field displays the asset tag number of the system.
Product Name This field shows product name of the system.
Manufacturer Name This field displays the manufacturer of this system.
UUID Number Universally Unique Identifier (UUID) is an identifier standard used in software construction, 
standardized by the Open Software Foundation (OSF) as part of the Distributed 
Computing Environment (DCE). 
						

							24Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot menu, 
SATA mode and recovery.
NOTE: The screen above is for your reference only. Actual values may differ. 
						

							Chapter 225
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is 
because the user is not allowed to control the settings in these cases.
ParameterDescriptionFormat/Option
System Time Sets the system time. The hours are displayed 
with 24-hour format.Format: HH:MM:SS 
(hour:minute:second) System Time
System Date Sets the system date. Format MM/DD/YYYY (month/day/
year)
System Date
System Memory This field reports the memory size of the system. 
Memory size is fixed to 640MB
Total Memory This field reports the total memory size of the 
system.
Extended Memory This field reports the memory size of the 
extended memory in the system. 
Extended Memory size=Total memory size-1MB
VGA Memory Shows the VGA memory size. 
Quiet Boot Determines if Customer Logo will be displayed or 
not; shows Summary Screen is disabled or 
enabled. 
Enabled: Customer Logo is displayed, and 
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and 
Summary Screen is enabled. Option: 
Enabled or Disabled
Network Boot Enables, disables the system boot from LAN 
(remote server).Option: 
Enabled or Disabled
F12 Boot Menu Enables, disables Boot Menu during POST.
Option: 
Disabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The 
function allows the user to create a hidden 
partition on hard disc drive to store operation 
system and restore the system to factory 
defaults.Option: 
Enabled or Disabled
SATA Mode Control the mode in which the SATA controller 
should operate.Option: AHCI or IDE 
						

							26Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized 
use.
NOTE: Please refer to “Remove HDD/BIOS Password” section if you need to know how to remove HDD/BIOS 
Password.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
ParameterDescriptionOption
Supervisor Password Is Shows the setting of the Supervisor password
Clear or Set
User Password Is Shows the setting of the user password.
Clear or Set
Set Supervisor Password Press Enter to set the supervisor password. 
When set, this password protects the BIOS 
Setup Utility from unauthorized access. The 
user can not either enter the Setup menu nor 
change the value of parameters.
Set User Password Press Enter to set the user password. When 
user password is set, this password protects 
the BIOS Setup Utility from unauthorized 
access. The user can enter Setup menu only 
and does not have right to change the value of 
parameters.
Password on Boot Defines whether a password is required or not 
while the events defined in this group 
happened. The following sub-options are all 
requires the Supervisor password for changes 
and should be grayed out if the user password 
was used to enter setup.
Disabled or Enabled 
						

							Chapter 227
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the up/down keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.Press Enter.
               After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press the F10 key to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.Use the up/down keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press Enter.
3.Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. 
The computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press F10 to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.Use the up/down keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Password box appears: 
						

							28Chapter 2
2.Type the current password in the Enter Current Password field and press Enter.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses F10.
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following 
message. 
						

							Chapter 229
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay. 
						

							30Chapter 2
Exit
The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the 
BIOS Setup Utility.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS. 
						

							Chapter 231
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
•New versions of system programs
•New features or options
•Restore a BIOS when it becomes corrupted. 
Use the Flash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery disk at hand, then you should create a Crisis Disk (See “Creating 
the Crisis Disk in Windows” on page 104)before you use the Flash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
NOTE: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does not 
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
completely loaded. 
Follow the steps below to run the Flash utility:
1.Rename the BIOS file as “XXXXXXX.FD”
2.Copy the “XXXXXXX.FD” file to a bootable USB device containing the Crisis Disk.
3.Turn off the system power.
4.Insert the USB device containing the renamed BIOS file and Crisis Disk to any USB port.
5.Make sure the AC adapter is connected to a power outlet and plugged in to the system.
6.Power on the system from an off state (i.e. cold boot) while holding down the Fn + ESC key.
7.After POST, release Fn + ESC key. The system should boot from the USB device and perform crisis 
recovery action. 
						

							32Chapter 2
Remove HDD Password
This section teaches you how to remove HDD password:
Remove HDD Password:
•If you key in the wrong HDD password thrice, “HDD password error code” will appear on the 
screen. See the image below.
•If you need to solve HDD password locked problem, you can run HDD_PW.EXE
1.Key in “hdd_pw 15494 0”
2.Select “2”
3.Choose one of the uppercase strings
•Reboot the system and key in “0KJFN42” or “UVEIQ96” as your HDD user password.