Acer Aspire 5739 Service Guide
Have a look at the manual Acer Aspire 5739 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 361 5.Clean the thermal pad off of the heat sink. Scrape the thermal pad off with a plastic implement and then use alcohol and a microfiber cloth to remove any residue from the heat sink. 6.Lift the CPU clear of the socket by grasping from the corners and carefully ease the CPU out from under the heat sink. WARNING:Take care to prevent the pins from becoming bent while removing the CPU. If you find it difficult to remove the CPU using this method, or lack the tools to properly remove the CPU clear of the socket, then remove the Thermal Module from the Mainboard first. See “Removing the Thermal Module” on page 82.
62Chapter 3 Main Unit Disassembly Process Main Unit Disassembly Flowchart Screw List StepScrewQuantityPart No. Hinge Covers M2*3 2 86.AD302.001 Switch Cover M2.5*3 4 86.AD302.002 M2.5*10 2 86.AD302.004 Function Board M2.5*3 2 86.AD302.002 Speaker Module M2.5*3 2 86.AD302.002 LCD Module M2.5*5 6 86.AD302.003 Upper Cover M2.5*10 10 86.AD302.004 M2.5*5 6 86.AD302.003 M2.5*3 1 86.AD302.002 Finger Print Reader M2*3 1 86.AD302.001 TouchPad Bracket M2*3 2 86.AD302.001 eKey Board M2.5*3 1 86.AD302.002 USB Board M2.5*3 1 86.AD302.002 Remove External Modules before proceeding Rem ove Thermal Module Rem ove Mainboard Rem ove Fingerprint Reader Rem ove Switch Cover Rem ove Keyboard Rem ove LCD Module Rem ove Bluetooth Module Rem ove Power Saving Boa r d Rem ove USB BoardRem ove Modem Module Lower CoverUpper Cover Rem ove Power Board Rem ove Upper Cover Rem ove TouchPad Bracket Rem ove eKey BoardRem ove Media Board Rem ove RJ-11 Port Rem ove Hinge Covers
Chapter 363 Removing the Hinge Covers 1.See “Removing the Battery Pack” on page 49. 2.Remove the two screw caps and screws from the Hinge Covers. 3.Slide the covers off the hinges in the direction of the arrows. IMPORTANT:The left and right Hinge Covers are shaped differently and marked L and R on the inside. Ensure that the correct cover is used during reassembly. Removing the Switch Cover CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1.See “Removing the Battery Pack” on page 49.Modem Module M2*3 2 86.AD302.001 BT Module M2.5*3 1 86.AD302.002 Mainboard M2.5*3 1 86.AD302.002 Thermal Module M2.5*5*3.2 4 86.AD302.006 StepSizeQuantityScrew Type Hinge Covers M2.5*4 2 StepScrewQuantityPart No.
64Chapter 3 2.See “Removing the Hinge Covers” on page 63. 3.Locate and remove the six securing screws on the bottom of the computer. 4.Turn the computer over and open the LCD module to expose the Switch Cover. IMPORTANT:The LCD module does not fully extend. Damage will occur if you attempt to extend the LCD module beyond the manufacturer’s design. 5.Pull the switch cover up from the left or right corner, separating the back edge first. StepSizeQuantityScrew Type Switch Cover (red callout)M2.5*6 6 Switch Cover (cyan callout)M2.5*4 2
Chapter 365 6.Using both hands, lift both sides of the rear edge of the Switch Cover upward as shown. 7.Place the switch board on the keyboard. 8.Disconnect the function board from the main unit by lifting the FFC lock and removing the FFC as shown.
66Chapter 3 9.Disconnect the power board from the main unit by lifting the FFC lock and removing the FFC as shown. Removing the Power Save Board 1.See “Removing the LCD Module” on page 68. 2.Disconnect the Power Save Board from the Function Board by lifting the FFC lock and removing the FFC as shown. 3.Remove the two screws securing the Power Save Board to the Switch Cover as shown. StepSizeQuantityScrew Type Switch Cover (red callout)M2.5*4 2
Chapter 367 4.Remove the Power Save Board from the Switch Cover. Removing the Power Switch Board 1.See “Removing the LCD Module” on page 68. 2.Remove the three screws securing the Power Save Board to the Switch Cover as shown. 3.Remove the power board by sliding it out from the securing tab as shown. Removing the Keyboard 1.See “Removing the Switch Cover” on page 63. 2.Pull up on the center rear of the keyboard until the Keyboard snaps free of the securing tabs on both sides of the Keyboard. StepSizeQuantityScrew Type Switch Cover (red callout)M2.5*4 3
68Chapter 3 IMPORTANT:The keyboard is still attached to the Mainboard FFC - do not pull on the keyboard. 3.Lay the keyboard face down on the touchpad. 4.Unlock the connector and pull the FFC to remove it from the Mainboard. 5.Remove the keyboard from the chassis. Removing the LCD Module 1.See “Removing the WLAN Module” on page 52. 2.See “Removing the Keyboard” on page 67.
Chapter 369 3.Turn the computer over. Remove the two securing screws as shown. StepSizeQuantityScrew Type LCD Module M2.5*5 2
70Chapter 3 4.Starting at the LCD module, completely remove the Antenna cable from the cable channel. 5.Rest the computer on its side with the LCD Module open and push the Antenna cable through the chassis as shown.