Acer Aspire 5735 Service Guide

							Chapter 131
Battery Type Li-ion
Pack capacity  6Cell 4400 MAH/8Cell 4800 MAH
Number of battery cell 6/8
Package configuration 3 cells in series, 2 series in parallel
4 cells in series, 2 series in parallel
LCD 15.4” inch
ItemSpecification
Vendor & model name CMO/AUO/LG
Screen Diagonal (mm) 15.4 inches
Display resolution (pixels) 1280 x 800 WXGA
Pixel Pitch 0.204 x 0.204
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
Typical White Luminance (NIT)
also called Brightness220
Luminance Uniformity 1.25 max.
Contrast Ratio 400 typical
Response Time msec 8
Nominal Input Voltage VDD +3.3V
Viewing Angle (degree)
Horizontal: Right/Left
Vertical: Upper/Lower45/45
15/35
Temperature Range( C)
Operating
Storage (shipping)0 to +50
-40 to +60
AC Adaptor
ItemSpecification
Input  100-240V~ 1.5A, 50-60Hz/
Output 19V 4.74A 90W/19V 3.42A 65W
System Power Management
ACPI modePower Management
Mech. Off (G3) All devices in the system are turned off completely.
Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned 
off completely.
Working (G0/S0) Individual devices such as the CPU and hard disc may be 
power managed in this state. Battery
ItemSpecification
° 
						

							32Chapter 1
Suspend to RAM (S3) CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4) Also called Hibernation Mode. System saves all system 
states and data onto the disc prior to power off the whole 
system. System Power Management
ACPI modePower Management 
						

							Chapter 233
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if 
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press  to enter Setup” message is prompted 
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change 
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”. 
Press  during POST to enter multi-boot menu. In this menu, user can change boot device without 
entering BIOS SETUP Utility.
Phoenix   SecureCore(tm)   Setup   Utility
Main
CPU Type:
CPU   Speed:
IDE0   Model   Name:
I D E 0   S e r i a l   N u m b e r :
ATAPI   Model   Name:
System   BIOS   Version:
VGA BIOS   Version:
KBC   Version:
Serial Number:
Asset Tag   Number:
Product   Name:
Manufacturer   Name:
UUID:Intel   (R)   Core   (TM)2   Duo   CPU T9400   @   2.53   GHz
2.53   GHz
XXXXXXXXXXX-(XX)
XXXXXXXX
XXXXXXXXXXX-XXX   XX-XXXX-(XX)
VX.XX
XX-XXX   XXXXXX.XXX.XXX.XXX.XXXXXX
XX.XX
XXXXXXXXXXXXXXXXXXXXXXX
None
Aspire   5730
Acer
XXXxXxXX-xXxX-XXxx-xXXx-xXXxXXxXxxXX
F1
EscHelp
ExitSelect    Item
Select    Menu
Change   Values
Select         Sub-Menu -/+
EnterF9
F10Setup   Defaults
S a v e   a n d   E x i t
InformationSecurity Boot Exit
System Utilities
Chapter 2 
						

							34Chapter 2
Navigating the BIOS Utility
There are five menu options: Information, Main, Security, Boot, and Exit.
Follow these instructions:
qTo choose a menu, use the left and right arrow keys.
qTo choose an item, use the up and down arrow keys.
qTo change the value of a parameter, press F5 or F6.
qA plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
qPress Esc while you are in any of the menu options to go to the Exit menu.
qIn any menu, you can load default settings by pressing F9. You can also press F10 to save any 
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a 
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item 
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please 
note that system information is subject to different models. 
						

							Chapter 235
Information
The Information screen displays a summary of your computer hardware information.
NOTE: The system information is subject to different models.
ParameterDescription
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
IDE0 Model Name This field shows the model name of HDD installed on primary IDE master.
IDE0 Serial Number This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name This field shows the model name of the Optical device installed in the system.
System BIOS Version Displays system BIOS version.
VGA BIOS Version This field displays the VGA firmware version of the system.
KBC Ver This field shows the keyboard 
Serial Number This field displays the serial number of this unit.
Asset Tag Number This field displays the asset tag number of the system.
Product Name This field shows product name of the system.
Manufacturer Name This field displays the manufacturer of this system.
UUID Number Universally Unique Identifier (UUID) is an identifier standard used in software construction, 
standardized by the Open Software Foundation (OSF) as part of the Distributed 
Computing Environment (DCE).
Phoenix   SecureCore(tm)   Setup   Utility
Main
CPU Type:
CPU   Speed:
IDE0   Model   Name:
I D E 0   S e r i a l   N u m b e r :
ATAPI   Model   Name:
System   BIOS   Version:
VGA BIOS   Version:
KBC   Version:
Serial Number:
Asset Tag   Number:
Product   Name:
Manufacturer   Name:
UUID:Intel   (R)   Core   (TM)2   Duo   CPU T9400   @   2.53   GHz
2.53   GHz
XXXXXXXXXXX-(XX)
XXXXXXXX
XXXXXXXXXXX-XXX   XX-XXXX-(XX)
VX.XX
XX-XXX   XXXXXX.XXX.XXX.XXX.XXXXXX
XX.XX
XXXXXXXXXXXXXXXXXXXXXXX
None
Aspire   5730
Acer
XXXxXxXX-xXxX-XXxx-xXXx-xXXxXXxXxxXX
F1
EscHelp
ExitSelect    Item
Select    Menu
Change   Values
Select         Sub-Menu -/+
EnterF9
F10Setup   Defaults
S a v e   a n d   E x i t
InformationSecurity Boot Exit 
						

							36Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option 
and recovery.
NOTE: The screen above is for your reference only. Actual values may differ.
Phoenix   SecureCore(tm)   Setup   Utility
Main
Item   Specific   Help
,   ,   or
   selects   field. System Time:
System   Date:
System   Memory:
Extended   Memory:
Video   Memory:
Quiet   Boot:
Network   Boot:
F12   Boot   Menu:
D2D   Recovery:
SATAMode
F1
EscHelp
ExitSelect    Item
Select    Menu
Change   Values
Select         Sub-Menu -/+
EnterF9
F10Setup   Defaults
S a v e   a n d   E x i t
Information Security
BootExit
[]
[]:10:10
07/26/2008
640   KB
4061   MB
3 2   M B
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[AHCI]10 
						

							Chapter 237
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is 
because the user is not allowed to control the settings in these cases.
ParameterDescriptionFormat/Option
System Time Sets the system time. The hours are displayed 
with 24-hour format.Format: HH:MM:SS 
(hour:minute:second) System Time
System Date Sets the system date. Format MM/DD/YYYY (month/day/
year)
System Date
System Memory This field reports the memory size of the system. 
Memory size is fixed to 640MB
Extended Memory This field reports the memory size of the 
extended memory in the system. 
Extended Memory size=Total memory size-1MB
VGA Memory Shows the VGA memory size. 
Quiet Boot Determines if Customer Logo will be displayed or 
not; shows Summary Screen is disabled or 
enabled. 
Enabled: Customer Logo is displayed, and 
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and 
Summary Screen is enabled. Option: 
Enabled or Disabled
Network Boot Enables, disables the system boot from LAN 
(remote server).Option: 
Enabled or Disabled
F12 Boot Menu Enables, disables Boot Menu during POST.
Option: 
Disabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The 
function allows the user to create a hidden 
partition on hard disc drive to store operation 
system and restore the system to factory 
defaults.Option: 
Enabled or Disabled
SATA Mode Control the mode in which the SATA controller 
should operate.Option: AHCI or IDE 
						

							38Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized 
use.
NOTE: Please refer to “Remove HDD/BIOS Password” section if you need to know how to remove HDD/BIOS 
Password.
Phoenix SecureCore(tm) Setup Utility
Main
F1
EscHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu -/+
EnterF9
F10Setup Defaults
Save and Exit
Information Security Boot Exit
Item Specific Help
Supervisor Password
controls access of the
whole setup utility.
Itcanbeusedtoboot
up when Password on
boot is enabled. Supervisor Password s:
User Password s:
:
Set User Password
Set Password
Password on Boot:i
i
HDD Password is
HDD Set Supervisor PasswordClear
Clear
Clear
[Enter]
[Enter]
[Disabled] []Enter 
						

							Chapter 239
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the “w” and “y” keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.Press e.
                After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
ParameterDescriptionOption
Supervisor Password Is Shows the setting of the Supervisor password
Clear or Set
User Password Is Shows the setting of the user password.
Clear or Set
HDD Password Is Shows the setting of the hard disk password.
Clear or Set
Set Supervisor Password Press Enter to set the supervisor password. 
When set, this password protects the BIOS 
Setup Utility from unauthorized access. The 
user can not either enter the Setup menu nor 
change the value of parameters.
Set User Password Press Enter to set the user password. When 
user password is set, this password protects 
the BIOS Setup Utility from unauthorized 
access. The user can enter Setup menu only 
and does not have right to change the value of 
parameters.
Set HDD Password Enter HDD Password.
Password on Boot Defines whether a password is required or not 
while the events defined in this group 
happened. The following sub-options are all 
requires the Supervisor password for changes 
and should be grayed out if the user password 
was used to enter setup.
Disabled or Enabled 
						

							40Chapter 2
Removing a Password
Follow these steps:
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The 
computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses u.