Acer Aspire 5650 Service Guide

							Chapter 365
5.Disconnect the keyboard cable from the main board.
6.Turn over the notebook, remove two screws fastening the LCD module on the bottom.
7.Then turn the notebook to the front side. Take out the antenna then disconnect the LCD cable (See the 
middle and the right images).
8.Remove four screws fastening the LCD module (M2.5*10(NL) for yellow circles; M2.5*15(NL) for red 
circles).
9.Then detach the entire LCD module from the main unit carefully. 
						

							66Chapter 3
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.Remove two screws fastening the upper case assembly to the lower case assembly.
2.Disconnect the LED board cable from the main board.
3.Disconnect the touchpad cable from the main board.
4.Remove eight screws fastening the upper case assembly and the lower case assembly on the bottom as 
shown.
5.Detach the upper case assembly carefully.
Disassembling the Upper Case Assembly
6.Remove the two screws fastening the media board.
7.Take out the media board cable from the lower case as shown.
8.Detach the media board from the upper case carefully. 
NOTE: Only Aspire 5650 series have media board.
9.Tear off the mylar on top of the touchpad bracket.
10.Remove the screws holding the touchpad bracket.
11 .Then detach the touchpad bracket from the uppwer case. 
						

							Chapter 367
12.Disconnect the touchpad FFC.
13.Then remove the touchpad FFC from the touchpad.
14.Detach the touchpad from the upper case.
Disassembling the Lower Case Assembly
1.Detach the switch board from the main board.
2.Remove the screw fastening the modem board.
3.Disconnect the modem board from the main board then detach the modem board.
4.Detach the modem cable from the lower case.
5.Disconnect the speaker cable from the main board.
6.Then disconnect the microphone cable from the main baord. 
						

							68Chapter 3
7.Remove the screw fastening the main board to the lower case.
8.Pull the lower case outwards as the image shows and detach the main board from the lower case 
carefully.
9.Take out the microphone from the lower case.
10.Remove the two screws fastening the speaker set.
11 .Take out the speaker from the lower case. 
						

							Chapter 369
Disassembling the LCD Module
1.Remove the four screw caps as shown.
2.Remove the four screws holding the LCD bezel.
3.Then detach the LCD bezel from the LCD module.
4.Remove the screw fastening the LCD inverter.
5.Take out the LCD inverter from the LCD cover, then disconnect the LCD cable from the inverter.
6.Disconnect the LCD power cable on the other side.
7.Remove the two screws fastening the LCD assembly.
8.Take out the LCD assembly from the LCD panel.
9.Tear off the tape fastening the LCD cable.
10.Remove the four screws fastening the LCD right bracket.
11 .Remove the LCD right bracket. 
						

							70Chapter 3
12.Remove the four screws holding the LCD left bracket.
13.Remove the LCD left bracket. 
						

							Chapter 371
Disassembling the External Modules
Disassembling the HDD Module
1.Remove two screws hodling the HDD bracket on one side.
2.Remove another two screws fastening the HDD bracket on the other side.
3.Detach the HDD from the HDD bracket.
Disassembling the ODD Module
1.Remove the three screws holding the optical bracket.
2.Remove the optical bracket from the optical disk drive. 
						

							72Chapter 3 
						

							Chapter 473
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or 
modified options can give false errors and invalid system responses.
1.Obtain the failing symptoms in as much detail as possible.
2.Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating 
the same operation.
3.Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)Go To
Power failure. (The power indicator does not go 
on or stay on.)“Power System Check” on page 75.
POST does not complete. No beep or error 
codes are indicated.“Power-On Self-Test (POST) Error Message” on 
page 78
“Undetermined Problems” on page 90
POST detects an error and displayed messages 
on screen.“Error Message List” on page 79
Other symptoms (i.e. LCD display problems or 
others).“Power-On Self-Test (POST) Error Message” on 
page 78
Symptoms cannot be re-created (intermittent 
problems).Use the customer-reported symptoms and go to 
“Power-On Self-Test (POST) Error Message” on 
page 78
“Intermittent Problems” on page 89
“Undetermined Problems” on page 90
Troubleshooting
Chapter 4 
						

							74Chapter 4
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is 
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause 
damage to the drive or cause the drive to fail. 
Do the following to select the test device.
1.Boot from the diagnostics diskette and start the diagnostics program.
2.See if FDD Test is passed as the program runs to FDD Test.
3.Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.Reconnect the external diskette drive/DVD-ROM module.
2.Replace the external diskette drive/CD-ROM module.
3.Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does 
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.Boot from the diagnostics diskette and start the diagnostics program.
2.See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.Reconnect the external diskette drive/CD-ROM module.
2.Replace the external diskette drive/CD-ROM module.
3.Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable 
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test. 
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a 
non-defective FRU:
1.Reconnect the keyboard cables.
2.Replace the keyboard.
3.Replace the main board.
The following auxiliary input devices are supported by this computer:
TNumeric keypad
TExternal keyboard