Acer Aspire 5534 Service Guide

							Chapter 351
5.Slide the ODD module out of the assembly
6.Remove the screws securing the ODD bracket and remove the ODD bracket from the optical disk drive 
module.
StepSizeQuantityScrew Type
ODD Module M2.5*3 1 
						

							52Chapter 3
 
7.Insert an appropriate tool into the manual ODD tray release to open the ODD tray.
8.Press down on the ODD bezel securing clip and pull the bezel out of the ODD.
StepSizeQuantityScrew Type
ODD Bracket M2*3 2 
						

							Chapter 353
Removing the DIMM Module
1.See “Removing the Battery Pack” on page 46
2.Loosen the two captive screws in the Memory Cover.
3.Lift the Memory Cover up to remove. Pull up using the thumb tab (indicated by the circle below) to release 
the seven clips securing the cover in place.
4.Identify the SODIMM to remove. The image below shows the locations of SODIMM slot 0 and SODIMM 
slot 1. Slot 0 must be populated first when installing or replacing defective memory.
5.Push out the release latches on both sides of SODIMM socket 1 to release the memory module. 
0
1 
						

							54Chapter 3
6.Remove the DIMM. 
7.Push out the release latches on both sides of SODIMM socket 0 to release the DIMM. 
8.Remove the DIMM.  
						

							Chapter 355 
						

							56Chapter 3
Removing the WLAN Board
1.See “Removing the Battery Pack” on page 46.
2.Loosen the two captive screws in the HDD Cover.
3.Lift the HDD cover up to remove. Use the finger tab to release the six clips securing the cover in place.
NOTE: The HDD is also located under this cover.
4.Disconnect the Antenna cables from the WLAN Board.
NOTE: Cable placement is White to the AUX terminal (right) and Black to the MAIN terminal (left). 
						

							Chapter 357
5.Remove the single screw securing the WLAN Board in place.
6.Remove the WLAN Board from the Mainboard.
StepSizeQuantityScrew Type
WLAN Board M2*3 1 
						

							58Chapter 3
Main Unit Disassembly Process
IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and 
replacement of components, ensure all available cable channels and clips are used and that the cables are 
replaced in the same position.
NOTE: The product previews seen in the disassembly procedures may not represent the final product color or 
configuration.
Main Unit Disassembly Flowchart
Screw List
StepScrewQuantityPart No.
Upper Cover M2.5*8 18 86.PEA02.006
Upper Cover M2.5*6 7 86.PEA02.007
Button Board M2*3 3 86.PEA02.002
TouchPad Bracket M2*3 1 86.PEA02.002
Power Board M2.5*3 1 86.PEA02.001
Speaker Module M2.5*3 4 86.PEA02.001
Media Board M2.5*3 1 86.PEA02.001
Remove
Mainboard
Remove
KeyboardRemove
Upper Cover
Remove
LCD Module
Remove
Power Board
Remove External
Modules bef ore
proceeding
Remove
Function BoardUpper
CoverLower
Cover
Remove
Left Speaker
Module
Remove
CPU
Remove
Thermal Module
Remove
Right Speaker
Module
Remove
CPU Fan
Remove
I/O Board
Remove
Power Socket
Remove
Touchpad BoardRemove
Touchpad
Bracket 
						

							Chapter 359
I/O Board M2.5*6 1 86.PEA02.007
Mainboard M2.5*6 1 86.PEA02.007
Mainboard (Fan) M2.5*6 1 86.PEA02.007
LCD Module M2.5*6 3 86.PEA02.007
Fan M2.5*6 1 86.PEA02.007
Thermal Module M2.5*6 (spring 
tension)4 86.PEA02.004
StepScrewQuantityPart No. 
						

							60Chapter 3
Removing the Keyboard
IMPORTANT: The keyboard is easily warped or damaged during the removal process. Take care not to use 
excessive force when removing the keyboard and replace if any damage occurs.
1.See “Removing the Battery Pack” on page 46.
2.Turn the computer rightside up and open the lid to the full extent.
3.Unlock the six securing latches by pressing down with a suitable plastic tool then sliding along the back 
edge of the keyboard.
IMPORTANT: The use of metal tools may damage the outer casing. Use plastic tools where available.
4.Pull up on the center of the keyboard to release the two tabs on each side and lift the Keyboard away from 
the Upper Cover as shown.
IMPORTANT: Do not remove the Keyboard from the Upper Cover; the Keyboard FFC is still attached.
5.Place the keyboard as shown.