Acer Aspire 5517 Service Guide

							Chapter 231
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Select Boot Devices to select specific devices to support boot.
PhoenixBIOS Setup Utility
Item Specific Help
Use < > or < > to
select a device, then
press  to move it
up the List, or 
to move it down the
list. Press  to
escape the menu.
F1
Es cHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu
EnterF9
F10Setup Defaults
Save and Exit
Boot priority order:
   1: IDE0: ST960821A
   2: IDE1: MATSHITADVD
   3: USB FDD:
   4: Network boot: Realtek Boot Agent
   5: USB HDD: xxxx USB
   6: USB CDROM:
  Boot priority order:
   1: IDE0: ST960821A
   2: IDE1: MATSHITADVD
   3: USB FDD:
   4: Network boot: Realtek Boot Agent
   5: USB HDD: xxxx USB
   6: USB CDROM:
 
F5/F6 Main Boot
Exit Security Information 
						

							32Chapter 2
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding 
ChangesExit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
PhoenixBIOS Setup Utility
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
F1
Es cHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu
EnterF9
F10Setup Defaults
Save and Exit
[Enter]
[Enter]
[Enter]
[Enter]
[Enter] [Enter]
[Enter]
[Enter]
[Enter]
[Enter]Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F5/F6 Main Boot
Exit Security Information 
						

							Chapter 233
BIOS Flash Utilities
The BIOS flash memory update is required for the following conditions:
• New versions of system programs
• New features or options
• Restore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not 
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
completely loaded. 
Fellow the steps below to run the Phlash.
1.Prepare a bootable diskette.
2.Copy the flash utilities to the bootable diskette.
3.Then boot the system from the bootable diskette. The flash utility has auto-execution function. 
						

							34Chapter 2
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1.Press F2 during boot to enter the Setup Menu.
2.Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move 
USB HDD to position 1.
3.Execute the FLASH.BAT batch file to update BIOS in DOS mode.
The flash process begins as shown.
PhoenixBIOS Setup Utility
Item Specific Help
Use < > or < > to
select a device, then
press  to move it
up the List, or 
to move it down the
list. Press  to
escape the menu.
F1
Es cHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu
EnterF9
F10Setup Defaults
Save and Exit
Boot priority order:
   1: IDE0: ST960821A
   2: IDE1: MATSHITADVD
   3: USB FDD:
   4: Network boot: Realtek Boot Agent
   5: USB HDD: xxxx USB
   6: USB CDROM:
  Boot priority order:
   1: IDE0: ST960821A
   2: IDE1: MATSHITADVD
   3: USB FDD:
   4: Network boot: Realtek Boot Agent
   5: USB HDD: xxxx USB
   6: USB CDROM:
 
F5/F6 Main Boot
Exit Security Information 
						

							Chapter 235
4.In flash BIOS, the message Please do not remove AC Power Source displays.
Plug in the AC power to continue.
5.Flash is complete when the message Flash programming complete displays. 
WinFlash Utility
Perform the following steps to use the WinFlash Utility:
1.Double-click the WinFlash executable.
2.Click OK to begin the update. WinFlash closes all applications and shuts down the system. 
NOTE: Place only one *.wph file with flash32.exe in the same folder when executing this procedure. 
						

							36Chapter 2
Remove HDD/BIOS Password Utilities
This section provides you with details about removing HDD/BIOS password:
Remove HDD Password:
If you key in the wrong HDD password three times, an error is generated.
To reset the HDD password, perform the following steps:
1.An error code is generated for unlocking the HDD. Note down this code.
2.Execute the UnlockHD.EXE file to create the unlock code in DOS Mode using the format UnlockHD  
[Encode code] with the code noted in the previous step, as follows:
UnlockHD  76943488
3.Select 2 to obtain the password. This password which can be used for unlocking the HDD.
Password :46548274
4.Shut down the computer by pressing down the Power button for 4 seconds.
5.Turn on the computer and key in the password to unlock the HDD. 
						

							Chapter 237
Removing BIOS Passwords:
To clear the User or Supervisor passwords through hardware, open the WLAN door and use a metal 
instrument to short the J1 jumper.
Cleaning BIOS Passwords
To clean the User or Supervisor passwords using software utilites, perform the following steps:
1.From a DOS prompt, execute clnpwd.exe
2.Press 1 or 2 to clean the desired password shown on the screen. 
						

							38Chapter 2
The onscreen message determines whether the function is successful or not.
Using Boot Sequence Selector
The Boot Sequence Selector allows the boot order to be changed without accessing the BIOS. To use Boot 
Sequence Selector, perform the following steps:
1.Enter into DOS.
2.Execute BS.exe to display the usage screen.
3.Select the desired boot sequence by entering the corresponding sequence. For example, enter BS2 to 
change the boot sequence to HDD | CD ROM | LAN | Floppy. 
						

							Chapter 239
Using DMITools
The DMI (Desktop Management Interface) Tool copies BIOS information to EEPROM to be used in the DMI 
pool for hardware management. 
When the BIOS displays Verifying DMI pool data it is checking that the table correlates with the hardware 
before sending to the operating system (Windows, etc.).
To update the DMI Pool, perform the following steps:
1.Boot into DOS.
2.Execute dmitools. The following messages report to screen to confirm completion:
• dmitools /r ==> Read dmi string from bios
• dmitools /wm xxxx ==> Write manufacturer name to eeprom (max. 16 characters)
• dmitools /wp xxxx ==> Write product name to eeprom (max. 16 characters)
• dmitools /ws xxxx ==> Write serial number to eeprom (max. 22 characters)
• dmitools /wu xxxx ==> Write uuid to eeprom
• dmitools /wa xxxx ==> Write asset tag to eeprom (max. 32 characters)
The following examples show the commands and the corresponding output information.
Read DMI Information from Memory
Input: 
dmitools /r
Output:
Manufacturer (Type1, Offset04h): Acer
Product Name (Type1, Offset05h): TravelMate xxxxx
Serial Number (Type1, Offset07h): 01234567890123456789
UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
Asset Tag (Type3, Offset04h): Acet Asstag
Write Product Name to EEPROM
Input:
dmitools /wp Acer
Write Serial Number to EEPROM
Input:
dmitools /ws 01234567890123456789
4 ). Write UUID to EEPROM ( Create UUID from Intel WFM20.pdf )
Input:
dmitools /wu
5). Write Asset Tag to EEPROM
Input:
dmitools /wa Acer Asstag
NOTE: When using any of the Write options, restart the system to make the new DMI data effective. 
						

							40Chapter 2
Using the LAN MAC EEPROM Utility
You can use the MAC.BAT utility to write the MAC.CFG file to the EEPROM under DOS mode.
1.Use a text editor (for example: Notepad) to open the MAC.CFG file. You can see the MAC.CFG contents 
as below:
2.In DOS mode, run the MAC.BAT file to write MAC values to eeprom. WriteData = ‘001122334455 MAC value
StartAddr=7A MAC address
WriteLeng=6 MAC value length
KeepByte=0 don’t care