Acer Aspire 5515 Service Guide

							90Chapter 3
Replacing the Camera
1.Reconnect the camera cable to the module.2.Replace the adhesive strip securing the cable to 
the camera module.
3.Replace the Camera board in the casing as shown. Ensure the locating pin is correctly seated.
4.Replace the Camera bracket on the board as 
shown5.Replace the single securing screw. 
						

							Chapter 391
6.Replace the Camera Module back cover as shown.7.Press down around the edges of the casing to snap 
it into place.
8.Replace the camera module in the casing as 
shown.9.Replace the camera cable as shown, using all the 
adhesive strips and cable clips.
10.Run the camera cable along the guides on the 
casing and press down to secure it in place.11 .Ensure that the cable passes through the hinge 
well as shown. 
						

							92Chapter 3
12.Replace the single securing screw as shown.13.Align the Latch Lid with the casing as shown.
14.Insert the left side latch as shown and press down 
to snap it in to place.15.Press down on the centre of the Lid Latch to snap it 
into place.
16.Insert the right side latch as shown and press down 
to snap it in to place.17.Reattach the Latch Spring as shown. 
						

							Chapter 393
18.Reconnect the left side of the spring as shown, 
						

							94Chapter 3
Replacing the LCD Panel
1.Align the LCD brackets with the screw holes on the panel. Starting with the top most screws (marked with  
U) replace the eight screws (four on each side) in the brackets as shown.
2.Insert the LCD Panel cable into the LCD Panel 
connector as shown.3.Replace the adhesive strip securing the connector 
in place.
4.Place the LCD Panel in the back cover. 
IMPORTANT: Ensure that the LCD power cable passes 
through the hinge well and is not trapped under the 
panel.5.Secure the LCD module with the two securing 
screws.
U
UU 
						

							Chapter 395
Replacing the Inverter
Replacing the LCD Bezel
1.Connect the right side inverter cable.2. Connect the left side inverter cable and place the 
inverter in the LCD module.
3.Replace the adhesive strips to secure the cables in 
place.4.Replace the two securing screws.
1.Locate the bezel bottom edge first and press down the edges until there are no gaps between the bezel and 
the LCD Module.
IMPORTANT: Ensure that the LCD cables pass through the hinge wells and are not trapped by the bezel. 
						

							96Chapter 3
2.Replace the four screws and the rubber screw caps provided. 
						

							Chapter 397
Main Module Reassembly Procedure
Replacing the CPU
IMPORTANT:The CPU has a Pin1 locator that must be positioned corresponding to the marker on the CPU 
socket.
1.Carefully turn the mainboard upside down (CPU side up), and place the CPU into the CPU socket as 
shown, taking note of the Pin1 locator.
2.Gently close the socket lever and snap it into place in the securing clip.
IMPORTANT:Do not force the lever closed. The CPU is incorrectly installed if resistance is encountered. 
Remove the CPU and ensure that all pins are straight and that Pin1 is correctly located.
Socket
Pin1 LocatorCPU
Pin1 Locator 
						

							98Chapter 3
Replacing the Speaker Modules
1.Place the left and right speaker modules in the chassis as shown.
2.Replace the two securing screws.
NOTE: The left and right speaker module securing screws differ slightly in length. Ensure the correct screw 
is used for each speaker.
•Left Speaker Module (red callout): M2.5*3
•Right Speaker Module (green callout): M2.5*6
3.Run the speaker cabling along the front of the casing as shown and replace the adhesive strips. 
						

							Chapter 399
Replacing the Internal Microphone
Replacing the Mainboard
1.Place the microphone in the chassis as shown.2.Run the cabling along the inside of the casing as 
shown.
3.Run the cable behind the speaker module as 
shown.4.Replace the adhesive strips to secure the cable in 
place.
1.Ensure that the Mainboard is face up (the CPU is not visible). Place the Mainboard in the chassis, front edge 
first (1), then rotate it downward into position (2).
2.Ensure that the locating pin is correctly seated and the speaker cable is positioned as shown (3).
(1)
(2)
(3)