Home > Acer > Notebook > Acer Aspire 5235 Service Guide

Acer Aspire 5235 Service Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Acer Aspire 5235 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Chapter 239
    The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
    parameter settings.
    NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
    your password. If you forget your password, you may have to return your notebook computer to your 
    dealer to reset it.
    Setting a Password
    Follow these steps as you set the user or the supervisor password:
    1.Use the “w” and “y” keys to highlight the Set Supervisor Password parameter and press the e key. The 
    Set Supervisor Password box appears:
    2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
    alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
    Password” field.
    IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
    3.Press e.
                    After setting the password, the computer sets the User Password parameter to “Set”.
    4.If desired, you can opt to enable the Password on boot parameter.
    5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
    ParameterDescriptionOption
    Supervisor Password Is Shows the setting of the Supervisor password
    Clear or Set
    User Password Is Shows the setting of the user password.
    Clear or Set
    HDD Password Is Shows the setting of the hard disk password.
    Clear or Set
    Set Supervisor Password Press Enter to set the supervisor password. 
    When set, this password protects the BIOS 
    Setup Utility from unauthorized access. The 
    user can not either enter the Setup menu nor 
    change the value of parameters.
    Set User Password Press Enter to set the user password. When 
    user password is set, this password protects 
    the BIOS Setup Utility from unauthorized 
    access. The user can enter Setup menu only 
    and does not have right to change the value of 
    parameters.
    Set HDD Password Enter HDD Password.
    Password on Boot Defines whether a password is required or not 
    while the events defined in this group 
    happened. The following sub-options are all 
    requires the Supervisor password for changes 
    and should be grayed out if the user password 
    was used to enter setup.
    Disabled or Enabled 
    						
    							40Chapter 2
    Removing a Password
    Follow these steps:
    1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
    Password box appears:
    2.Type the current password in the Enter Current Password field and press e.
    3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The 
    computer then sets the Supervisor Password parameter to “Clear”.
    4.When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
    Changing a Password
    1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
    Password box appears:
    2.Type the current password in the Enter Current Password field and press e.
    3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
    field.
    4.Press e. After setting the password, the computer sets the User Password parameter to “Set”.
    5.If desired, you can enable the Password on boot parameter.
    6.When you are done, press u to save the changes and exit the BIOS Setup Utility.
    If the verification is OK, the screen will display as following. 
    The password setting is complete after the user presses u. 
    						
    							Chapter 241
    If the current password entered does not match the actual current password, the screen will show you the 
    Setup Warning.
    If the new password and confirm new password strings do not match, the screen will display the following 
    message. 
    						
    							42Chapter 2
    Boot
    This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
    includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
    Phoenix SecureCore(tm) Setup Utility
    Main
    Item Specific Help
    Useorto
    select a device, then
    presstomoveit
    up the list, or 
    to move it down the
    list. Press  to
    escape the menu. Boot priority order:
    F1
    EscHelp
    ExitSelect Item
    Select Menu
    Change Values
    Select Sub-Menu -/+
    EnterF9
    F10Setup Defaults
    Save and Exit
    Information Security Boot Exit
    2:
    3:
    4:
    5:
    6:
    7:: XXXXXXXXXXX-XXX XX-XXXX-XX
    PCI LAN: Network Boot
    USB HDD:
    USB FDD:
    USB Key:
    USB CDROM: 1: IDE HDD: XXXXXXXXXXX-(XX)
    IDE CD 
    						
    							Chapter 243
    Exit
    The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the 
    BIOS Setup Utility.
    The table below describes the parameters in this screen.
    ParameterDescription
    Exit Saving Changes Exit System Setup and save your changes to CMOS.
    Exit Discarding Changes Exit utility without saving setup data to CMOS.
    Load Setup Default Load default values for all SETUP item.
    Discard Changes Load previous values from CMOS for all SETUP items.
    Save Changes Save Setup Data to CMOS.
    Phoenix SecureCore(tm) Setup Utility
    Main
    Item Specific Help
    Exit System Setup and
    save your changes to
    CMOS.
    F1
    EscHelp
    ExitSelect Item
    Select Menu
    Change Values
    Select Sub-Menu -/+
    EnterF9
    F10Setup Defaults
    Save and Exit
    Information Security
    BootExit
    Exit Discarding Changes
    Load Setup Defaults
    Discard Changes
    Save Changes Exit Saving Changes 
    						
    							44Chapter 2
    BIOS Flash Utility
    The BIOS flash memory update is required for the following conditions:
    •New versions of system programs
    •New features or options
    •Restore a BIOS when it becomes corrupted. 
    Use the Flash utility to update the system BIOS flash ROM.
    NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
    Diskette before you use the Flash utility.
    NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
    NOTE: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does not 
    contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
    completely loaded. 
    Fellow the steps below to run the Flash.
    1.Prepare a bootable diskette.
    2.Copy the flash utilities to the bootable diskette.
    3.Then boot the system from the bootable diskette. The flash utility has auto-execution function. 
    						
    							Chapter 245
    Remove HDD/BIOS Utility
    This section provide you with removing HDD/BIOS method:
    Remove HDD Password:
    •If you key in wrong HDD password for three time, “HDD password error code” would display on the 
    screen. See the image below.
    •If you need to solve HDD password locked problem, you can run HDD_PW.EXE
    1.
    Key in “hdd_pw 15494 0”
    2.Select “2”
    3.Choose one upper-case string
    •Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password. 
    						
    							Chapter 347
    This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
    maintenance and troubleshooting.
    Disassembly Requirements
    To disassemble the computer, you need the following tools:
    •Wrist grounding strap and conductive mat for preventing electrostatic discharge
    •Flat screwdriver
    •Philips screwdriver
    •Hex screwdriver
    •Plastic flat screwdriver
    •Plastic tweezers
    NOTE: The screws for the different components vary in size. During the disassembly process, group the 
    screws with the corresponding components to avoid mismatch when putting back the components.
    Chapter 3
    Machine Disassembly and Replacement 
    						
    							48Chapter 3
    General Information
    Pre-disassembly Instructions
    Before proceeding with the disassembly procedure, make sure that you do the following:
    1.Turn off the power to the system and all peripherals.
    2.Unplug the AC adapter and all power and signal cables from the system. 
    3.Place the system on a flat, stable surface. 
    4.Remove the battery pack.
    Disassembly Process
    The disassembly process is divided into the following stages:
    •External module disassembly
    •Main unit disassembly
    •LCD module disassembly
    The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence. 
    Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you 
    want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly 
    frame in that order. 
    Main Screw List
    ItemScrewColorPart No.
    A M2 x L8 Black 86.00E34.738
    B M2.5 x L6 Black 86.00E12.536
    C M2 x L3 Silver 86.9A522.3R0
    D M3 x L4 Silver 86.9A524.4R0
    E M2.5 x L10 Silver 86.00F84.73A
    F M2 x L4 Silver 86.00C07.220
    G M2 x L4 Black 86.00A02.140
    H M2 x L3 Black 86.9A552.3R0 
    						
    All Acer manuals Comments (0)

    Related Manuals for Acer Aspire 5235 Service Guide