Acer Aspire 5230 Service Guide

							Chapter 3109
8. Secure the cable by pressing down on the securing 
strip.9. Replace the two securing screws on the LCD 
Module.
10.Replace the camera board in the bracket.11 .Replace the securing screw on the camera board.
12.Replace the Camera Module in the bottom cover.13.Replace the two securing screws on the Camera 
Module bracket. 
						

							11 0Chapter 3
14.Connect the Camera Module cable as shown. 15. Connect the left and right Inverter board cables as 
shown.
16.Connect the left and right Inverter board cables as shown.
17.Replace the inverter board and secure with the two provided screws. 
						

							Chapter 3111
Replacing the LCD Bezel
18.Replace the securing tapes from the left and right sides of the Inverter board as shown.
NOTE: Tuck the cables securely to prevent damage to the cables or module.
1. Align the edge of the bezel with the bottom cover and replace the LCD Module.
2.Replace the two upper and two lower bezel screw caps. Remove the four securing screws from the LCD 
module.
  
						

							11 2Chapter 3
Main Module Reassembly Procedure
Replacing the VGA Module
Replacing the CPU
1.Insert the VGA Module as shown.2.Replace the two securing screws on the VGA 
Module.
1.Carefully turn the mainboard upside down (CPU 
side up), and insert the CPU into the CPU bracket 
as shown.2. Using a flat-tipped screw driver, lock the CPU in 
the socket as shown. 
						

							Chapter 311 3
Replacing the Thermal Module
Replacing the RJ-11 Port
1.Align and place the Thermal Module in the 
mounting as shown.2.Connect the fan module cable to the mainboard.
3.Replace the eight securing screws from the Thermal Module.
1.Insert the RJ-11 port into the base as shown.2.Using the tweezers, grasp the end of the cable and 
press down to attach it to the base. 
						

							11 4Chapter 3
3.Replace the RJ-11 cable in its housing. 
						

							Chapter 311 5
Replacing the Mainboard
1.Replace the power jack in the Lower Cover. 2.Gently lower the mainboard, leftside first, on the 
lower base. Ensure the screw sockets are aligned.
3.Ensure that the Mainboard is face up (the Heatsink and CPU are not visible). Place the Mainboard in the 
chassis, rear edge first, and press down to install. Replace the two securing screws as shown.
NOTE: Make sure the I/O ports are positioned correctly through the lower cover, and the screw sockets are 
visible through the mainboard.
4.Connect the two cables on the top right of the 
mainboard as shown.5.Connect the three cables from the bottom right of 
the mainboard as shown. 
						

							11 6Chapter 3
Replacing Subwoofer Module
Replacing the Modem Module
6.Locate the Subwoofer on the lower cover, and replace the two securing screws.
7.Connect the subwoofer cable as shown.
1.Connect the modem cable and locate it over the screw socket.
2.Insert module in mainboard. 
						

							Chapter 311 7
Replacing the USB Board
1.Angle the right side of the USB board into the lower base. Align the screw sockets and replace the two 
securing screws.
2.Replace the cable on the USB board. 3.Replace the securing screw on the modem module. 
						

							11 8Chapter 3
Replacing the Bluetooth Board
Replacing the TV Board
1.Angle the TV board into the lower base and lower into position.
2.Replace the two securing screws on the TV board.
3.Connect the antenna and single cable to the board. 1.While holding the Bluetooth module, connect the 
cable as shown.2.Position the module over the aligning pins and 
insert in place.