Acer Aspire 4230 Service Guide

Chapter 241
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding 
ChangesExit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS....

42Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
•New versions of system programs
•New features or options
•Restore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please...

Chapter 243
Remove HDD/BIOS Utility
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
•If you key in wrong HDD password for three time, “HDD password error code” would display on the 
screen. See the image below.
•If you need to solve HDD password locked problem, you can run HDD_PW.EXE
1.
Key in “hdd_pw 15494 0”
2.Select “2”
3.Choose one upper-case string
•Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password. 

44Chapter 2 

Chapter 245
Remove BIOS Password:
•If you key in wrong Supervisor Password for three time, “System Disabled” would display on the 
screen. See the image below.
•If you need to solve BIOS password locked problem, you can run BIOS_PW.EXE
1.
Key in “bios_pw 14452 0”
2.Choose one upper-case string
•Reboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password. 

46Chapter 2 

Chapter 347
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for 
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
•Wrist grounding strap and conductive mat for preventing electrostatic discharge
•Flat screwdriver
•Philips screwdriver
•Plastic flat screwdriver
•Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly...

48Chapter 3
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1.Turn off the power to the system and all peripherals.
2.Unplug the AC adapter and all power and signal cables from the system. 
3.Place the system on a flat, stable surface. 
4.Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
•External module disassembly
•Main unit disassembly
•LCD module...

Chapter 349
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you 
on the components that need to be removed during servicing. For example, if you want to remove the 
mainboard, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Screw List
StepScrewQuantityPart No.
WLAN Module M2.5*4 2 86.T23V7.009
HDD Module M2.5*4 2 86.T23V7.009
HDD...

50Chapter 3
Removing the Battery Pack
1.Turn computer over. 
2.Slide the battery lock/unlock latch to the unlock position. 
3.Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the 
main unit (2). 
(1) (2)