Acer Aspire 3630 Service Guide
Have a look at the manual Acer Aspire 3630 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
26Aspire 3630 Resolution, colors and maximum refersh rate (Hz) in 256, 65K or 16.7M colors. NOTE: 16:9 aspect ratio monitors are supported on 1920x1080 and 848x480 on Windows(R)XP, Windows(R) 2000 and Windows(R)ME. The complete list of resolutions depends on the driver version and operating system. NOTE: resolutions are limited by the performance of the attached monitor. USB Port ItemSpecification USB Compliancy Level 2.0 OHCI USB 2.0 Number of USB port 3 Location Two on the right side; one on the front side Serial port function control Enable/Disable by BIOS Setup PCMCIA Port ItemSpecification PCMCIA controller TI PC1410 Supports card type Type II (No Tpye III) Number of slots One type II Access location Right side Supports ZV (Zoomed Video) port NO Supports 32 bit CardBus Yes (IRQ17) Keyboard ItemSpecification Keyboard controller EC NS PC97551 keyboard controller Keyboard vendor Darfon Total number of keypads 88-/89-key Windows keys Yes Internal & external keyboard work simultaneously Yes Battery ItemSpecification Vendor & model name SANYO 4cell 2.0 SONY 4cell 2.0 SIMPLO 4cell 2.0 PANASONIC 8cell 2.2 SANYO 8cell 2.2 Battery Type Lithium-ION Pack capacity 2000mAH for SANYO 4cell, SONY 4cell, SIMPLO 4cell 4400mAH for PANASONIC 8cell, SANYO 8cell Nominal voltage 14.8V Number of battery cell 4 for SANYO/SONY/SIMPLO 8 for PANASONIC/SANYO Package configuration 4S1P for SANYO 4cell/SONY/SIMPLO 4S2P for PANASONIC/SANYO 8cell Package voltage Not show
Chapter 127 LCD 15.4” ItemSpecification Vendor & model name SAMSUNG LTN154X3-L01- glareLG LP154W01-TLA2 lead-free, glare Screen Diagonal (mm) 15.4inch 15.4inch Active Area (mm) 331.2(H)x207.0(V) 331.2(H)x207.0(V) Display resolution (pixels)WXGA (1080x800) WXGA (1080x800) Pixel Pitch 0.25875(H)x0.25875(H)mm 0.25875(H)x0.25875(H)mm Pixel Arrangement RGB vertical stripe RGB vertical stripe Display Mode Normally white Normally white Surface Treatment Haze 0 (Glare), Hardness 3H Hard coating (2H) glare+ Anti reflective treatment of the front polarizer Typical White Luminance (cd/m 2) also called Brightness200 185 Luminance Uniformity not show not show Contrast Ratio 300 300 Response Time (Optical Rise Time/Fall Time)msec25(rise+falling) 30(rise+falling) Nominal Input Voltage VDD not show not show Typical Power Consumption (watt) 3.7 (for backlight unit) Total 5.26 @LCM circuit 1.12, backlight input 4.14 Weight not show 590 Physical Size(mm) 344(W)x222(H)x6.5(D) 344(W)x222(H)x6.5(D) Support Color Native 262K colours 262K colours Viewing Angle (degree) Horizontal: Right/Left Vertial: Upper/Lower45/45 15/3560/60 40/50 Temperature Range( C) Operating Storage (shipping)0 to 50 -20 to -600 to 50 -20 to -60 LCD 15.4” ItemSpecification Vendor & model name AUO B154EW01 V8, lead-free AUO B154EW01 V9, lead-free, glareQDI QD15TL07-01, lead-free QDI QD15TL07-02, lead-free, glare Screen Diagonal (mm) 15.4inch 390.1 (15.4inch) Active Area (mm) 331.2(H)x207.0(V) 331.2(H)x207.0(V) Display resolution (pixels)WXGA (1280x800) WXGA (1280x800) Pixel Pitch 0.25875(H)x0.25875(H)mm 0.2588(H)x0.2588(H)mm Pixel Arrangement RGB vertical stripe RGB vertical stripe Display Mode Normally white Normally white Surface Treatment AG for V8 BV for V9Anti-Glare; Hardness 3H for -01 Glare+ Hard Coating 3H for -02 Typical White Luminance (cd/m 2) also called Brightness180 185 Luminance Uniformity not show 1.3 °
28Aspire 3630 Contrast Ratio 400 400 Response Time (Optical Rise Time/Fall Time)msec16(rise+falling) 16(rise+falling) Nominal Input Voltage VDD not show not show Typical Power Consumption (watt) 6.5W Not show Weight 585g 585g Physical Size(mm) 344(W)x222(H)x6.5(D) 344(W)x222(H)x6.35(D) Support Color Native 262K colours 262K colours Viewing Angle (degree) Horizontal: Right/Left Vertial: Upper/Lower40/40 10/3045/45 15/35 Temperature Range( C) Operating Storage (shipping)0 to 50 -20 to 600 to 50 -25 to 60 LCD 15.0” ItemSpecification Vendor & model name AUO B150XG02V.4 LEAD-FREELG LPL LP150X08- TLA2QDI QD150XL06- 03-01 lead-free Screen Diagonal (mm) 381 381 381 Active Area (mm) 304.1(H)x228.1(V) 304.1(H)x228.1(V) 304.1(H)x228.1(V) Display resolution (pixels) XGA (1024x768) XGA (1024x768) XGA (1024x768) Pixel Pitch 0.297(H)x0.297(H) mm0.297(H)x0.297(H) mm0.297(H)x0.297(H) mm Pixel Arrangement RGB vertical stripe RGB vertical stripe RGB vertical stripe Display Mode Normally white Normally white Normally White Surface Treatment Not Show Hard coating (3H) glare+ Anti reflective treatment of the front polarizerAnti-glare and hard- coating 3H Low reflection Typical White Luminance (cd/m 2) also called Brightness200 (5 point average)170 160 Luminance Uniformity 1.25 max (5pts) 1.65 max (13pts)not show not show Contrast Ratio 300 250 300 Response Time (Optical Rise Time/Fall Time)msec18/7 10/20 8/17 Nominal Input Voltage VDD +3.3 Typ not show +3.3 Typ Typical Power Consumption (watt) 5.6 4.76 not show Weight 575g 530g 570g Physical Size(mm) 317.3(W)x242.0(H) x6.0(D)317.3(W)x241.5(H) x5.9(D)317.3(W)x241.5(H) x5.9(D) Support Color Native 262K colours 262K colours 262K colours Viewing Angle (degree) Horizontal: Right/Left Vertial: Upper/Lower40/40 10/3045/45 15/3545/45 15/35 LCD 15.4” ItemSpecification °
Chapter 129 Temperature Range( C) Operating Storage (shipping)0 to 50 -20 to 600 to 50 -20 to 600 to 50 -25 to 60 AC Adapter ItemSpecification Vendor & model name LITE-ON - 65W, PA-1650-02 QY Input Requirements Maximum input current (A, @90Vac, full load)1.5 A @ 110Vac 1.0 A @ 240Vac Nominal frequency (Hz) 50-60 Frequency variation range (Hz) 47-63 Input voltage range (Vrms) 90-265 Inrush current Shall not be less than 220Amps (cold start) when AC input is 100V 60Hz and DC output is +19V 3.42A Shall not be less than 220Amps (cold start) when AC input is 240V 50Hz and DC output is +19V 3.42A Efficiency It should provide an efficiency of 85% (typ. 88%) minimum, when measured at maximum nominal voltage at 19.0V Output Ratings (CV mode) DC output voltage 19V Noise + Ripple 380mV Load Voltage Nom. (V) Capacitance Nom. Material Type 25.0 10/1.0 TAN/CERAMIC Output Ratings (CC mode) DC output voltage 19V +/-0.95 for CV mode Constant current mode 3.6 +0.60A/-0.3A Dynamic Output Characteristics Turn-on delay time 5 sec (@ 115Vac) Hold up time 5ms (@115Vac, Full load) Over Voltage Protection (OVP) 29V Short circuit protection 5.0A max can be protected and output can be shorted without damage Electrostatic discharge (ESD) +/-15KV (at air discharge) +/-8KV (at contact discharge) Dielectric Withstand Voltage Primary to secondary 2150Vac Leakage current 100uA Regulatory Requirements Safety Requirements: 1.The power supply must comply with the following national standards: UL, CSA, CCC, BSM, PCBC< CE, FIMKO, DEMKO, NEMKO, SIMKO, TUV 2. Dielectric Strength-primary to secondary: 2150 VDC for 1sec. 3. Insulation Resistance- primary to secondary: 30 Meg. ohms Min., 500VDC 4. Ground Leakage Current- the power supply ground leakage current shall be less than 100uA. LCD 15.0” ItemSpecification °
30Aspire 3630 Power Management Power Saving ModePhenomenon Standby Mode Enter Standby Mode when 1.Standby/Hibernation hot-key is pressed and system is not ready to enter Hibernation mode. 2.System standby/ Hibernation timer expires and system is not ready to enter Hibernation mode. TThe buzzer beepsTThe Sleep indicator lights up Hibernation Mode Enter Hibernation Mode (suspend to HDD) when 1.Hibernation hot-key is pressed and system is ready to enter Hibernation mode 2.System Hibernation timer expires and system is ready to enter Hibernation mode. TAll power shuts off Display Standby Mode Keyboard, built-in touchpad, and an external PS/2 pointing device are idle for a specified period. TThe display shuts off Hard Disk Standby Mode Hard disk is idle within a specified period of time. THard disk drive is in standby mode. (spindle turned-off) Environmental Requirements ItemSpecification Temperature Operating +0~+35 °C Non-operating -20~+65 °C Package storage -20~+65 °C Humidity Operating 10% to 90% RH, non-condensing Non-operating 10% to 90% RH, non-condensing (Unpacked) Non-operating 10% to 90% RH, non-condensing (Storage package) Vibration Operating (unpacked) Operation vibration: 1.0G ,X,Y,Zaxis, 30 minutes/axis Non-operating (unpacked) 5~27.1Hz: 0.6G 27.1~50Hz: 0.04mm (peak to peak) 50~500Hz: 2.0G Non-operating (packed) 5~62.6Hz: 0.51mm (peak to peak) 62.6~500Hz: 4.0G Mechanical Specification ItemSpecification Dimensions 364(W) x 279(D) x 33.9/38.98 (H)mm 14.3 X 11 x 1.3/1.5 inches Weight 6.08 Ibs (2.76kg) for 15” XGA LCD model 6.17 lbs (2.8kg) for 15.4” WXGA LCD model
Chapter 131 I/O Ports Three USB 2.0 ports Ethernet (RJ-45) port Modem (RJ-11) port External display (VGA) port Microphone/line-in jack Headphones/speaker/line-out jack Type II PC Card slot DC-in jack for AC adaptor Drive Bays One Material Plastic Indicators LED indicator for keyboard hot key: Caps Lock, Scroll Lock, NUmber lock LED indicator for function indicator: System power-on, HDD/ODD, Wireless on/off, Arcade LED mode, DC-in, Battery/Charging indicator Switch Power Mechanical Specification ItemSpecification
Chapter 232 BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises. To activate the BIOS Utility, press m during POST (when “Press to enter Setup” message is prompted on the bottom of screen). Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change boot device without entering BIOS Setup Utility, please set the parameter to “enabled”. Press during POST to enter multi-boot menu. In this menu, user can change boot device without entering BIOS SETUP Utility. PhoenixBIOS Setup Utility . Info. Main Advanced Security Boot Exit CPU Type : Mobile AMD Sempron (TM) Processor 2600+ CPU Speed : System BIOS Ver V1.0 VGA BIOS Ver KBC Ver Serial Numberxxxxxxxxxxxxxxxxxxxxxx Asset Tag Number N/A Produce Name Aspire 3000 Manufacturer Name: Acer UUID: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx F1 Help ↑↓ Select Item F5/F6 Change Values F9 Setup Defaults Esc Exit ← → Select Menu Enter Select 4Sub-Menu F10 Save and Exit HDD Model Name : HDD Serial Number : 22 Byte 32 Byte 16 Byte 16 Byte 32 Byte ATAPI Model Name : ATAPI Serial Number None System Utilities Chapter 2
33Chapter 2 Navigating the BIOS Utility There are six menu options: Info., Main, System Devices, Security, Boot, and Exit. Follow these instructions: TTo choose a menu, use the cursor left/right keys (zx). TTo choose a parameter, use the cursor up/down keys ( wy). TTo change the value of a parameter, press por q. TA plus sign (+) indicates the item has sub-items. Press e to expand this item. TPress ^ while you are in any of the menu options to go to the Exit menu. TIn any menu, you can load default settings by pressing t. You can also press u to save any changes made and exit the BIOS Setup Utility. NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a particular menu are shown on the bottom of the screen. Help for parameters are found in the Item Specific Help part of the screen. Read this carefully when making changes to parameter values. Please note that system information vary in models.
Chapter 234 Information NOTE: The system information is subject to different models. ParameterDescription HDD Model Name This field shows the model name of HDD installed on primary IDE master. HDD Serial Number This field displays the serial number of HDD installed on primary IDE master. ATAPI Model Name This field displays the mofel name of devices installed on secondary IDE master. The hard disk drive or optical drive model name is automatically detected by the system. ATAPI Serial Number This field shows the serial number of devices installed on secondary IDE master. Serial Number This field displays the serial number of this unit. UUID Number This will be visible only when an internal LAN device is presenting. UUID=32bytes PhoenixBIOS Setup Utility . Info. Main Advanced Security Boot Exit CPU Type : Mobile AMD Sempron (TM) Processor 2600+ CPU Speed : System BIOS Ver V1.0 VGA BIOS Ver KBC Ver Serial Numberxxxxxxxxxxxxxxxxxxxxxx Asset Tag Number N/A Produce Name Aspire 3000 Manufacturer Name: Acer UUID: xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx F1 Help ↑↓ Select Item F5/F6 Change Values F9 Setup Defaults Esc Exit ← → Select Menu Enter Select 4Sub-Menu F10 Save and Exit HDD Model Name : HDD Serial Number : 22 Byte 32 Byte 16 Byte 16 Byte 32 Byte ATAPI Model Name : ATAPI Serial Number None
35Chapter 2 Main The Main screen displays a summary of your computer hardware information, and also includes basic setup parameters. It allows the user to specify standard IBM PC AT system parameters. NOTE: The screen above is for reference only. Actual values may differ. PhoenixBIOS Setup Utility Info. Main Advanced Security Boot Exit Item Specific Help System Time: [15:56:48] System Date: [03/18/2005] System Memory: 640 KB Extended Memory: 446MB Video Memory [64 MB] Quiet Boot: [Enabled] Power on display: [Auto ] Network boot [Enabled] F12 Boot Menu [Disabled] , , or selects field. F1 Help ↑↓ Select Item F5/F6 Change Values F9 Setup Defaults Esc Exit ← → Select Menu Enter Select 4Sub -Menu F10 Save and Exit Shows system base memory size Shows extended memory size VGA memory size D2D Recovery USB BIOS Legacy [Disabled] [Enabled]