Acer Aspire 2930 User Manual
Have a look at the manual Acer Aspire 2930 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 351 5.Remove the four screws securing the hard disk to the carrier. NOTE: Replace the screws according to the numbering sequence as shown in the previous image. 6.Remove the HDD from the carrier. StepSizeQuantityScrew Type HDD Carrier M3*3 4 HDD right side 1 2 HDD left side 3 4
52Chapter 3 Removing the Optical Drive Module 1.See “Removing the Battery Pack” on page 44. 2.Loosen the screw to remove the ODD cap. 3.Remove the single securing screw. 4.Using a screw driver, push the ODD module and grasp the front panel to remove from the computer. StepSizeQuantityScrew Type ODD Module M2.5*8 1
Chapter 353 5.Remove the two screws securing the ODD bracket and remove the ODD bracket from the optical disk drive module. IMPORTANT:Do not remove the ODD bezel by pulling on it entirely or damage will occur. 6.Grasp the edge of the bezel and firmly pry the top edge down and outward to remove. StepSizeQuantityScrew Type ODD Bracket M2*3 2
54Chapter 3 Removing the DIMM Modules 1.Remove the Memory Cover. See “Removing the Lower Covers” on page 47. IMPORTANT:It is advisable to use a plastic pry during this procedure. 2.Use a pry to release the latches on both sides of the DIMM socket. 3.Remove the DIMM module. 4. Repeat steps for the second DIMM module.
Chapter 355 Main Unit Disassembly Process Main Unit Disassembly Flowchart Screw List StepScrewQuantityPart No. Switch Cover M2.5*5 2 86.ART02.004 Speaker Module M2.5*4 4 86.ART02.003 LED Board M2*3 1 86.ART02.001 Power Board M2*3 1 86.ART02.001 LCD Module M2.5*5 2 86.ART02.004 M2.5*4 4 86.ART02.003 M2*3 1 86.ART02.001 Upper Cover M2.5*5 1 86.ART02.004 M2.5*8 7 86.ART02.005 M2.5*5 5 86.ART02.004 Finger Print Reader M2*3 1 86.ART02.001 TouchPad Bracket M2*3 1 86.ART02.001 Rem ove Switch CoverRem ove Keyboard Remove External Modules before proceeding Rem ove AntennaRem ove Speaker Module Rem ove LCD Module Rem ove Touchpad Bracket Rem ove Launch BoardRem ove Finger Print Reader Upper Cover Rem ove LED BoardRem ove Power Board Rem ove I/O BoardRem ove Modem Board Rem ove Thermal Module Rem ove CPU Rem ove Mainboard Rem ove Bluetooth Board Lower Cover Rem ove USB Board Rem ove RJ-11Jack
56Chapter 3 Launch Board M2*3 3 86.ART02.001 USB Board M2*3 1 86.ART02.001 I/O Board M2*3 1 86.ART02.001 Modem Module M2*3 2 86.ART02.001 Mainboard M2*3 3 86.ART02.001 StepScrewQuantityPart No.
Chapter 357 Removing the Switch Cover CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1.See “Removing the Battery Pack” on page 44. 2.Locate and remove the two securing screws as shown. 3.Turn the computer over and open the LCD module to expose the Switch Cover. 4.Pry the right corner up and partially lift up. Do not pull the Switch Cover completely off at this time. IMPORTANT:Do not remove both sides of the Switch Cover together to prevent damage to the cover. Instead lift one end first and follow the instructions as directed. StepSizeQuantityScrew Type Switch Cover M2.5*5 2
58Chapter 3 5.While holding the corner, firmly move the Switch Cover back (A) and forth (B) to release the locking catches (four in front and four in back) on the back and front of the Switch Cover. 6.Repeat the wiggling procedure until the Switch Cover is removed. 7.After the Switch Cover is unlocked, lift it clear of the chassis. A B
Chapter 359 Removing the Keyboard 1.See “Removing the Switch Cover” on page 57. 2.Grasp the middle of the keyboard and firmly and lift up to remove. 3.Turn the keyboard over and unlock the connector to release the FFC from the mainboard.
60Chapter 3 Removing the Speaker Module 1.Remove the Keyboard. See “Removing the Keyboard” on page 59. 2.Remove the four securing screws. 3.Pull back the adhesive strips to expose the Speaker cabling. 4.Using the tweezers, disconnect the cabling as shown. StepSizeQuantityScrew Type Speaker Module M2.5*4 4