Acer Aspire 1690 Service Guide

							84Chapter 4
PCMCIA-Related Symptoms
Symptom / ErrorAction in Sequence
System cannot detect the PC Card (PCMCIA)  PCMCIA slot assembly
System board
PCMCIA slot pin is damaged. PCMCIA slot assembly
Memory-Related Symptoms
Symptom / ErrorAction in Sequence
Memory count (size) appears different from 
actual size.Enter BIOS Setup Utility to execute “Load Default Settings, then 
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / ErrorAction in Sequence
In Windows, multimedia programs, no sound 
comes from the computer. Audio driver
Speaker
System board
Internal speakers make noise or emit no sound. Speaker
System board
Power Management-Related Symptoms
Symptom / ErrorAction in Sequence
The system will not enter hibernation Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesnt enter hibernation mode and 
four short beeps every minute.See “Hibernation Mode” on page 34.
Press Fn+
oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode after 
closing the LCDSee “Hibernation Mode” on page 34.
LCD cover switch
System board
The system doesnt resume from hibernation 
mode.See “Hibernation Mode” on page 34.
Hard disk connection board
Hard disk drive
System board
The system doesnt resume from standby mode 
after opening the LCD.See “Hibernation Mode” on page 34.
LCD cover switch
System board
Battery fuel gauge in Windows doesn’t go higher 
than 90%. Remove battery pack and let it cool for 2 hours
Refresh battery (continue use battery until power off, then charge 
battery)
Battery pack
System board 
						

							Chapter 485
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined 
Problems” on page 87.
System hangs intermittently. Reconnect hard disk/CD-ROM drives. 
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / ErrorAction in Sequence
System configuration does not match the 
installed devices. Enter BIOS Setup Utility to execute “Load Default Settings”, then 
reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly. Press Fn+F5, LCD/CRT/Both display switching
System board
USB does not work correctly System board
Print problems. Ensure the “Parallel Port” in the “Onboard Devices Configuration” of 
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems. Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup 
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / ErrorAction in Sequence
Keyboard (one or more keys) does not work. Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work. Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / ErrorAction in Sequence
Internal modem does not work correctly. Modem phone port
modem combo board
System board
Power Management-Related Symptoms
Symptom / ErrorAction in Sequence 
						

							86Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a 
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement 
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.If no error is detected, do not replace any FRU.
3.If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.  
						

							Chapter 487
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, 
whether a short circuit is suspected, or whether the system is inoperative.  
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power 
System Check” on page 75):
1.Power-off the computer.
2.Visually check them for damage. If any problems are found, replace the FRU.
3.Remove or disconnect all of the following devices:
TNon-Acer devices
TPrinter, mouse, and other external devices
TBattery pack
THard disk drive
TDIMM 
TCD-ROM/Diskette drive Module
TPC Cards
4.Power-on the computer.
5.Determine if the problem has changed.
6.If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
TSystem board
TLCD assembly 
						

							88Chapter 4
Use NAPP CD to Build Master Hard Disc Drive
CD to Disk Recovery
1.Prepare NAPP CD, Recovery CD and System CD.
2.Put NAPP CD into the optical drive. Then boot up the system.
3.The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.NAPP CD will start to preload the system, please click [Y]. 
						

							Chapter 489
5.Select CD to Disk Revocery.
6.Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have 
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till 
you finish all Recovery CDs.
After you place the Recovery CD to the optical drive, you will see the display below. 
						

							90Chapter 4
7.Then insert the System CD to the optical drive.
8.You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive. 
						

							Chapter 491
Disk to Disk Recovery
1.Prepare NAPP CD, Recovery CD and System CD.
2.Put NAPP CD into the optical drive. Then boot up the system.
3.The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.NAPP CD will start to preload the system, please click [Y]. 
						

							92Chapter 4
5.Select Disk to Disk Recovery. Then choose Single Language or Multi-Languages Recovery.
NOTE: For Multi-Languages Recovery, not more than five languages could be loaded to the system.
6.Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have 
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till 
you finish all Recovery CDs. 
						

							Chapter 493
After you place the Recovery CD to the optical drive, you will see the display below.
7.Then insert the System CD to the optical drive.