Acer As211 Users Guide

							41
EnglishOSD Messages
Problems with the Projector
# Condition Message Reminder
1 Message•Fan Fail - the system fan is not working.
•Projector Overheated - the projector has exceeded its 
recommended operating temperature and must be allowed 
to cool down before it may be used. Please check the 
following message. 
Please also check the dust filters if they are installed. If the 
dust filter is clogged with dust, please clean it. Please refer to 
Cleaning and replacing the dust filter for details.
•Replace the lamp - the lamp is about to reach its maximum 
lifetime. Prepare to replace it soon.
# Condition Solution
1 The projector stops responding 
to all controlsIf possible, turn off the projector, then 
unplug the power cord and wait at least 30 
seconds before reconnecting power.
2 Lamp burns out or makes a 
popping soundWhen the lamp reaches the end of its useful 
life, it will burn out and may make a loud 
popping sound. If this happens, the projector 
will not turn on until the lamp module has 
been replaced. To replace the lamp, follow 
the procedures in the Replacing the Lamp 
section.
Downloaded From projector-manual.com Acer Manuals 
						

							42
English
LED & Alarm Definition Listing
LED Messages
MessageLamp_LED Temp_LED Power LED
Red Red Red Blue
Input power plug Flash ON to 
OFF 100msFlash ON to 
OFF 100msFlash ON to 
OFF 100ms--
Standby -- -- ON --
Power button ON -- -- -- ON
Lamp retry -- -- -- Quick 
Flashing
Power off (Cooling state) -- -- Quick 
Flashing--
Power button OFF
(cooling completed; 
standby mode)-- -- ON --
Error (thermal failure) -- ON -- ON
Error (fan lock) -- Quick 
Flashing-- ON
Error (lamp breakdown) ON -- -- ON
Error (color wheel fail) Quick 
Flashing-- -- ON
Downloaded From projector-manual.com Acer Manuals 
						

							43
EnglishCleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned 
periodically, they can become clogged with dust, preventing proper ventilation. 
This can cause overheating and damage the projector.
Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then 
unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Pull out the dust filter. (Illustration #1)
4 To clean the dust filters, use a small vacuum cleaner designed for 
computers and other office equipment. (Illustration #2)
5 If the dirt is difficult to remove or the filter is broken, please contact your 
local dealer or service center to obtain a new filter.
12
Downloaded From projector-manual.com Acer Manuals 
						

							44
English
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the 
lamp.
The projector will detect the lamp life. You will be shown a warning message 
Lamp is approaching the end of its useful life in full power operation. 
Replacement suggested! When you see this message, change the lamp as soon 
as possible. Make sure the projector has been cooling down for at least 30 
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down 
before changing the lamp.
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1 Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
2 Remove the screw that secure the lamp module. (Illustration #3)
Pull out the lamp plug. (Illustration #4)
Lift the handle so that it stands up. (Illustration #5)
3 Lift the handle so that it stands up. Pull out the lamp module by force. 
(Illustration #6)
To replace the lamp module, use a new lamp and reverse the above steps.
Warning: To reduce the risk of personal injury, do not drop the 
lamp module or touch the lamp bulb. The bulb may shatter and 
cause injury if it is dropped.
12
6
4
53
Downloaded From projector-manual.com Acer Manuals 
						

							45
EnglishCeiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the 
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and 
secure the mount base.
Note: Screws are not included. Please obtain the appropriate 
screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of four-cylinder screws.
20 mm13mm
8.4mm
130 mm
49.9mm
Ceiling Mount Base- Attach to ceiling
Screw Type A50 mm length / 8 mm diameter  -
Long Rod
Extension Rod
Long Cylinder Cap
Tightening Screw
Medium Rod Allen Key
- For tightening/loosening
Short Rod
Downloaded From projector-manual.com Acer Manuals 
						

							46
English
3 Use the appropriate number of screws for the projector size to attach the 
projector to the ceiling mount bracket.
Note: It is recommended that you keep a reasonable space 
between the bracket and the projector to allow for proper heat 
distribution. Use two washers for extra support, if deemed 
necessary.
4 Attach the ceiling bracket to the ceiling rod.
-   
Smaller Washer
Projector BracketLarge Washer
Supports projector and
allows for adjustmentsScrew Type B
Spacer
- For heat dissipation
-   Screw Type A50 mm length/
8 mm diameter
Large cylinder cap
Allen Key
Tightening Screw
- For tightening/loosening
Downloaded From projector-manual.com Acer Manuals 
						

							47
English5 Adjust the angle and positioning as necessary.
Note: The appropriate type of screw and washer for each model is 
listed in the table below. 4 mm diameter screws are enclosed in 
the screw pack.
Screw Type B Washer Type
Diameter (mm) Length (mm) Large Small
425VV
Tightening Screw
Allen Key
Tightening Screw Allen Key
85.00 mm 55.00 mm
82.30 mm
63.81 mm
SCREW SPEC. M4 x 25 mm
Downloaded From projector-manual.com Acer Manuals 
						

							48
English
Specifications
The specifications listed below are subject to change without notice. For final 
specs, please refer to Acers published marketing specifications.
Projection system
DLP®
Resolution•P1183/M403/PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV-S60/V10S/AS201/
X113H/X113PH/D600D/EV-S60H/V12S/AS211 series: 
Native 800 x 600 SVGA resolution
•P1283/M413/PE-X42/V12X/AX316/P1283n/M413T/
PE-X42G/X1283/X1280/D613/EV-X62 series: Native 
1024 x 768 XGA resolution
•P1383W/X1383WH/M423/PE-W42/V12W/AW316/
P1380W/X1380WH/M420/PE-W40/V11W/AW216 
series: Native 1280 x 800 WXGA resolution
•H5380BD/E230/HE-720 series: 1280x720 720p 
resolution
•P1510/P1515/M450/PE-840/H6520BD/E240D/HE-804J 
series: 1920x1080 1080p resolution
•Maximum: UXGA (1600 x 1200), WSXGA+ 
(1680x1050), 1080p(1920x1080), WUXGA-RB (1920 
x 1200)
Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and 
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+, 
WXGA, WXGA+, WSXGA +
Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p, 
576p), SDTV (480i, 576i)
Aspect ratio Full, 4:3, 16:9, L.Box
Displayable colors 16.7 million colors
Projection lens
•P1183/M403 PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV-S60/V10S/AS201/
X113H/X113PH/D600D/EV-S60H/V12S/AS211/P1283/
M413/PE-X42/V12X/AX316/P1283n/M413T/PE-X42G/
X1283/X1280/D613/EV-X62 series: 
F = 2.41 ~ 2.55, f = 2.79~23.99 mm, 1.1x manual 
zoom and manual focus
•P1383W/X1383WH/M423/PE-W42/V12W/AW316/
P1380W/X1380WH/M420/PE-W40/V11W/AW216 
series: 
F = 2.5 ~ 2.67, f = 21.80 ~ 23.98 mm, 1.1x manual 
zoom and manual focus
•H5380BD/E230/HE-720 series:
F = 2.5 ~ 2.67, f = 21.86 mm ~ 24.00 mm, 1.1x 
manual zoom and manual focus
•P1510/P1515/M450/PE-840/H6520BD/E240D/HE-804J 
series:
F = 2.5 ~ 2.67, f = 21.90 mm ~ 24.00 mm, 1.1x 
manual zoom and manual focus
Downloaded From projector-manual.com Acer Manuals 
						

							49
EnglishProjection screen size (diagonal)•P1183/M403 PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV-S60/V10S/AS201/
X113H/X113PH/D600D/EV-S60H/V12S/AS211/P1283/
M413/PE-X42/V12X/AX316/P1283n/M413T/PE-X42G/
X1283/X1280/D613/EV-X62 series: 
27 (70 cm) ~ 300 (762 cm)
•P1383W/X1383WH/M423/PE-W42/V12W/AW316/
P1380W/X1380WH/M420/PE-W40/V11W/AW216 
series: 
27 (69 cm) ~ 300 (762 cm)
•H5380BD/E230/HE-720 series: 
27 (67 cm) ~ 300 (762 cm)
•P1510/P1515/M450/PE-840/H6520BD/E240D/HE-804J 
series:
42 (106 cm) ~ 300 (762 cm)
Projection distance
•P1183/M403 PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV-S60/V10S/AS201/
X113H/X113PH/D600D/EV-S60H/V12S/AS211/P1283/
M413/PE-X42/V12X/AX316/P1283n/M413T/PE-X42G/
X1283/X1280/D613/EV-X62 series: 
3.9 (1.2 m) ~ 39.0 (11.9 m)
•P1383W/X1383WH/M423/PE-W42/V12W/AW316/
P1380W/X1380WH/M420/PE-W40/V11W/AW216 
series: 
3.3 (1.0 m) ~ 32.9 (10.0 m)
•H5380BD/E230/HE-720 series: 
3.3 (1.0 m) ~ 33.8 (10.3 m)
•P1510/P1515/M450/PE-840/H6520BD/E240D/HE-804J 
series:
4.9 (1.5 m) ~ 32.2 (9.8 m)
Throw ratio
•P1183/M403 PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV-S60/V10S/AS201/
X113H/X113PH/D600D/EV-S60H/V12S/AS211/P1283/
M413/PE-X42/V12X/AX316/P1283n/M413T/PE-X42G/
X1283/X1280/D613/EV-X62 series: 50@2 m (1.95 ~ 
2.15:1)
•P1383W/X1383WH/M423/PE-W42/V12W/AW316/
P1380W/X1380WH/M420/PE-W40/V11W/AW216 
series: series: 60@2 m (1.55 ~ 1.70:1)
•H5380BD/E230/HE-720 series: 58@2m (1.55 ~ 1.70:1)
•P1510/P1515/M450/PE-840/H6520BD/E240D/HE-804J 
series: 61@2m (1.48 ~ 1.62:1)
Horizontal scan rate 15 - 100 kHz
Vertical refresh scan rate 24 - 120 Hz
Lamp type
•P1183/M403/PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV- S60/V10S/
AS201/X113H/X113PH/D600D/EV-S60H/V12S/AS211/
P1283/M413/PE-X42/V12X/AX316/P1283n/M413T/
PE-X42G/X1283/X1280/D613/EV-X62/P1383W/
X1383WH/M423/PE- W42/V12W/AW316/P1380W/
X1380WH/M420/PE-W40/V11W/AW216/H5380BD/
E230/HE-720 series: 190 W user-replaceable lamp
•P1510/P1515/M450/PE- 840/H6520BD/E240D/HE-
804J series: 240 W user-replaceable lamp
Downloaded From projector-manual.com Acer Manuals 
						

							50
English
Keystone correction
±40 degrees
Audio P1183/M403/PE-S42/X1183A/D603P/EV-S62T/P1283/
M413/PE-X42/V12X/AX316/P1283n/M413T/PE-X42G/
X1283/X1280/D613/EV-X62/P1383W/X1383WH/M423/
PE-W42/V12W/AW316/P1380W/X1380WH/M420/PE-
W40/V11W/AW216/H5380BD/E230/HE-720/P1510/
P1515/M450/PE-840/H6520BD/E240D/HE-804J: Internal 
speaker with 2 W output
Weight 2.5 ~ 2.7 Kg (5.51 ~ 5.95 Ibs)
Dimensions (W x D x H) 314 mm X 223.4 mm X 93.4 mm (12.4 x 8.8 x 3.7)
Digital Zoom 2X
Power supply AC input 100 - 240 V auto-switching power supply
Power consumption
•P1183/M403/PE-S42/X1183A/D603P/EV-S62T/X114/
X1183/D603/EV-S62/X113/D600/EV-S60/V10S/AS201/
X113H/X113PH/D600D/EV-S60H/V12S/AS211/P1283/
M413/PE-X42/V12X/AX316/P1283n/M413T/PE-X42G/
X1283/X1280/D613/EV-X62/P1383W/X1383WH/
M423/PE-W42/V12W/AW316/P1380W/X1380WH/
M420/PE-W40/V11W/AW216/H5380BD/E230/HE-
720:
Normal mode: 235W ± 10% @ 110VAC
ECO mode: 197W ± 10% @ 110VAC
Standby mode < 0.5W
•P1510/P1515/M450/PE-840/H6520BD/E240D/HE-804J 
series:
Normal mode: 300W ± 10% @ 110VAC
ECO mode: 230W ± 10% @ 110VAC
Standby mode < 0.5W
Operating temperature 0ºC to 40ºC / 32ºF to 104ºF
Standard package contents
•AC power cord x1
•VGA cable x1
•Remote control x1
•Battery x2 (for remote control) (option)
•Users guide (CD-ROM) x1
•Quick start guide x1
•Security card x1
•Carrying case x1 (option)
I/O 
connectorsX113/D600/
EV-S60/
V10S/
AS201/
X114/
X1183/
D603/
EV-S62X113H/
X113PH/
D600D/
EV-S60H/
V12S/
AS211/X1183A/
X1280/
D603P/
EV-S62T/
X1283/
D613/
EV-X62P1183/M403/PE-
S42/P1283/M413/
PE-X42/V12X/
AX316/P1383W/
X1383WH/M423/
PE-W42/V12W/
AW316/P1380W/
X1380WH/M420/
PE-W40/V11W/
AW216/
H5380BD/E230/
HE-720P1283n/
M413T/
PE-X42GP1510/
P1515/
M450/
PE-840H6520BD/
E240D/
HE-804J
Power socket V V V V V V V
VGA IN V V X X X V V
Downloaded From projector-manual.com Acer Manuals