Accusplit Stopwatch AX602M500DEC User Manual

b-1
ACCUSPLIT, Inc.
6120 Stoneridge Mall Rd., Suite 210 Pleasanton, CA 94588 USA
800-965-2008  •  925-226-0888  •  FAX 925-463-0147
www.ACCUSPLIT.com  •  [email protected]
980-314
ACCUSPLIT®
E X CLUSIVE
AX602M500
AX602M500DEC
DIGITAL QUARTZ  STOPWATCHES
OPERATING
INSTRUCTIONS
2-3
 2  3
IMPORTANT NOTE
This stopwatch can store up to 500 split/lap times. 
However please note when there are 5 free mem-
ories left, the icon “FULL” will blink to remind you 
of the nearly full situation. Whenever the...

4-5
 4 5
General Features
•   ACCUSPLIT X case with ergonomic design and 
  no-fail buttons
•   4 button operation
•   Large LCD display with contrast adjustment
•   12/24 hour display
•   Time of day and chime
•   Daily alarm
•   Full 1/100 second chronograph with working 
  range from 0 to 19 hr. 59 min. 59.99 seconds 
  with 500 memory records of split and lap time.
•   Recall function for recorded split and lap times
•   Count-Down timer with working range from 0 to 
  19 hr. 59 min. 59.9 seconds•...

8-9
 8 9
This is only a brief description of these buttons. 
Detailed uses of the buttons are different in 
particular functions and will be described later in 
the instructions.
Pressing [MODE] button will toggle among the 
modes above. Note that there is no auto-return 
function in the stopwatch. Whenever you change 
modes, the stopwatch will remain in that mode 
until the [MODE] button is pressed again.Time of Day Mode
The starting point for operating your stopwatch 
is  TIME OF DAY. If  TIME OF DAY...

12-13
 12 13
date-month (d-m), Sound ON or OFF, Contrast 
(darkness of the digits - default is 9), then back to 
Second, and recycles again. 
Note: when the second is to be set, press [START 
•  SPLIT] to reset the second digits to zero. At the 
end of setting, press [RECALL] (S4) or [MODE] to 
exit from the setting mode and back to Time of 
Day Display.
Display for Sound ON or 
OFF setting :
(Let the current status be “ON”.)
Press [START •  SPLIT] to toggle 
Sound ON or OFF.
Display for contrast...

16-17
 16 17
Chronograph and Recall Mode
Press [MODE] until you enter the Chrono mode.
The stopwatch can measure up to 19 hours, 
59 minutes, 59.99 seconds. When you enter the 
Chronograph mode, the display format is as 
below.The upper line shows the split time, the middle 
line shows the lap time and the accumulated 
elapsed time is displayed on the lower line.
Whenever the stopwatch stops running, the 
“STOP” indicator will be ON. Press the button 
[START •  SPLIT] to start the stopwatch. As it runs,...

20-21
 20 21
When there are 5 free memories left, the icon 
“FULL” will blink to remind you of the nearly 
full situation. Whenever the storage is full, extra 
split/lap times will not be stored into memory but 
will still be shown on the display. Any fastest and 
slowest laps will not be stored. The memory coun-
ter will  ash as the extra split/lap times are being 
displayed. The  icon  “FULL ” will be steadily ON.
The maximum memory counter value is 500.
To stop the chronograph, press [STOP •  RESET]....

24-25
 24 25
Please note that if the stopwatch is running, no 
selection for chronograph operating modes can 
be made until the stopwatch has been stopped 
and reset.
Segmented run memory for lap/split time storage.
A header consisting of the date/time stamp is 
attached to each segment to indicate the moment 
when you began recording the particular timing 
segment. To get to this feature, press [MODE] in 
chronograph mode to enter DATA mode when 
the stopwatch has been stopped. Records for dif-
ferent...

28-29
 28 29
[RECALL]
[RECALL] 
[RECALL]
[RECALL] 
[RECALL]
After recalling the  rst record, press [RECALL] 
once more to exit from Recall mode and go back 
to chronograph mode. The “RECALL” icon will 
turn OFF.
Note: watch is 
still running 
so run time 
continues to 
advance.
30-31
 30 31
DATA Mode
Press [MODE] until you enter DATA mode.  The 
mode message “DATA” will be shown for one to 
two seconds before the number of free memories 
is to be shown.
You can press [START •  SPLIT] to scroll through...

32-33
 32 33
The header consisting of the date/time stamp will 
be shown. The number of laps in the segment will 
appear in the upper left while the segment num-
ber is displayed in the middle left. If the segment 
shown is not your desired segment, press [START 
•  SPLIT] to reach the desired segment. The current 
segment will be accessed  rst, then it will cycle 
back to the 1st, then 2nd and so on.
When you have found the segment you want, you 
can press [RECALL] button consecutively to read 
the lap...

36-37
 36 37
Note: You cannot delete all segments while the 
stopwatch is running. If nothing happens when 
you push and hold [STOP •  RESET] check to 
make sure the stopwatch is stopped.Timer Mode
Press [MODE] until you enter the Timer mode. 
3 count-down operation modes are available on 
this stopwatch:
  •  Count down repeat (CR)
  •  Count down stop (CS)
  •  Count down, then count up (CU)
The timer is set at the factory to the count-down 
repeat (CR) mode. At entering timer mode, the 
mode message...