Accusplit Stopwatch AE760M100 LONG User Manual

 Press [RECALL] again to view the average lap time.
Press [RECALL] continually to review all the stored split/lap times. The sequence starts from the last record
to the first record when the stopwatch is running and vice versa when the stopwatch has been stopped.
[RECALL]
[RECALL]
[RECALL]
0: 00 05 120: 03 16 03
RECALL                   AVG
LAP
RU N{005}
0: 00 14 910: 00 02 050: 03 28 94
SPLIT
LAP
RU N{005}RECALL
0: 00 12 860: 00 01 600: 03 33 64
SPLIT
LAP
RU N{004}RECALL
0: 00 11 260: 00 01 780: 03 40...

[RECALL]
After recalling the first record, press [RECALL] once more to exit from Recall mode and go back to chronograph
mode.   The RECALL icon will be OFF.
[RECALL]
During memory recall,  you can press either [START], [STOP] or [LAP/SPLIT] to exit from chrono recall mode
and jump to the chrono start/stop or lap state respectively.
Data Mode (AE760M & AE790M Model only)Press [MODE] until you enter DATA mode The mode message DATA will be shown for one to two seconds
before the number of free memories is...

The header consisting of the date/time stamp will be shown.  The number of laps in the segment will appear
in the upper left while the segment number is displayed in the middle left.  If the segment shown is not your
desired segment, press [START] to reach the desired segment. The current segment will be accessed first,
then it will cycle back to the 1st, then 2nd and so on.
When you have found the segment you want, you can press [RECALL] button consecutively to read the lap
records from the first to the...

How to delete all memory segments:-
Instead of deleting one segment, you can also delete all memory segments.  When you enter the Data mode,
you see the screen FREE XXX LAP. Press and hold the [RESET] for 3 seconds. You will hear Beep, beep,
beep for 3 seconds, then a long Beep. At this point all data in the memory will be deleted and DELETE
ALL  will show on the display.
If you dont want to delete the records, you can press any key to exit DELETE ALL  state before the end of
the ready period and resume...

Under CS operation mode, the timer, after counting down to 0:0000, will stay at 0:00000 until you press
[RESET] to reload the timer value.
Under CU operation mode, the timer, after counting down to 0:00000, will count up and stop at 19:59599.
How to set the timer
Press and hold [RECALL] for 2 seconds to activate timer setting.   Timer setting starts with second digits,
which are shown blinking.  You can press [START] to advance the flashing digits.  Or you can press [RESET]
to select other digits.  The...

Pacer ModePress [MODE] until you enter the Pacer mode. In the Pacer mode, you can set the standard pacer speed from
5 to 240 beats per minute in the following values:
5, 10, 20,  30,  40,  50,  60,  80, 100, 120,  150,  180,  200,  240
In Pacer mode, the display will be:-
The digits are flashing to indicate that the pace count is ready for setting. Press [RESET] to select the pace
count. Once the desired pace count is selected, press [START] to confirm the setting and start the pace
count. The display...

In the Stroke Measurement mode, the duration of 3 strokes is taken and the stroke frequency (counts per
minute) is calculated.  As the stroke frequency falls out of the range of 10 - 180,  Err will appear to show the
error condition.
Press [START] to start the measurement. During the 1st second, 180.0 will be shown and flashing as below.
At the end of the first second, the display will become steady.
If measurement is stopped in the first second (stroke frequency > 180), error signal  Err  will be shown....

Distance SettingPress [RECALL] for 2 seconds to enter setting mode, the unit icon flashes.
Press [START] to toggle between KM and MILE.  To select the following digits, press [RESET].   The far right
digit will blink and you can set the distance from the least significant digit to the most significant digit. The
distance can be set in the range 0.000 to 1999.999 km (or ML).  Press [RECALL] OR [MODE] to exit from the
setting mode.
As an example, the distance is set at 400m.
Speed Mode RunningPress [START]...

Press [LAP/SPLIT] to record more lap times and show different speeds.  Note that as the speed exceeds the
value 1999.999 km/hr or 1999.999 mph, Err will be shown and no storage will be made for that record.
[LAP/SPLIT]
[LAP/SPLIT]
To stop the speed measurement, press [STOP] to stop the timer.
Before star ting again, you can reset the timer by pressing [RESET].
Note: When you reset the Speed timer, the speed measurement starts again from a reset state, and all speed
records in memory will be cleared...

Lap Time & Speed RecallSimilar to the Chrono Recall mode, during speed measurement or Stop state, you can press [RECALL] to
recall the speed/lap memories.  The Mode message will be shown for one to two seconds as the Mode
message display is displayed.
The Speed and Lap time will be displayed on the upper and the middle lines.  The lower line shows the current
time counting.  During Data recall, the fastest speed will be reviewed first, then the slowest speed and average
speed.
Further presses of [RECALL]...