Accusplit Pedometer AE1640M4 User Manual

							
SETTING UP YOUR PEDOMETER 
To record your distance and calories accurately, you will  
need to set your stride length. 
CHOOSING A MEASUREMENT SYSTEM 
This unit is initially set to use English measurement units  
(Miles).  To change the unit back and forth between English 
and Metric units (Kilometers), press the yellow RESET button 
for 5 seconds. 
Finding Your Stride Length: Your stride length is the length of 
one of your steps, measured from “toe to toe.” To measure, 
walk 10 steps with your normal stride and measure the 
TOTAL DISTANCE from the toe of your starting step to the 
toe of your 10th step (see diagram below). Divide the TOTAL 
DISTANCE by 10. This is your stride length. Example: If you 
walk 22 feet, your stride length is 2.2 feet. 
Setting Your Stride Length: Press the aqua MODE button 
until arrow on top of display points to MILES or KM. Press 
the cream SET button once to enter setting mode. Display 
will shift to show stride (for example, “F 1.95” means stride 
is set to 1.95 feet). Press the cream SET button to increase 
stride length. Press the yellow RESET button  to reduce stride 
length. Press the aqua MODE button to exit setting mode.  
WEARING YOUR PEDOMETER
While gently holding the belt clip open, slide the pedometer 
onto your belt or the top edge of your pants or skirt. It 
should fit snugly and level, above one knee. 
Note: The pedometer should be as vertical as possible. 
Walkers with larger stomachs may find it helpful to wear the 
pedometer farther back on the body, toward one hip. 
The cover must be closed for the pedometer to work. To 
avoid losing or dropping your pedometer, use the included 
leash and clip to fasten the pedometer securely to your 
clothing. 
Attaching the Leash: Attach the pedometer to the leash by 
looping the leash around the pedometer belt clip. Next, clasp  
the waistband of your clothing with the attached metal clip. 
You can also use a safety pin to fasten the leash to your 
clothing, or loop the leash through your belt or belt loop. 
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, 
it will automatically begin to record your steps, distance, 
calories burned, and activity time. Repeatedly press the 
yellow MODE button to cycle through the pedometer modes: 
STEPS → DISTANCE → ACTIVITY  TIMER → STEPS
ACCUSPLIT, Inc.  •  6120 Stoneridge Mall Rd., Suite 210  •  Pleasanton, CA 94588 USA
800-965-2008  •  925-226-0888  •  FAX 925-463-0147  •  www.ACCUSPLIT.com  •  [email protected]
10 steps
Congratulations on taking the first step to wellness 
with your purchase of an ACCUSPLIT pedometer.  
It’s easy to set up your new pedometer.  
Just follow the steps below, and start walking!
MEMORY PEDOMETER
OPERATING INSTRUCTIONS
ACCUSPLIT®
       EAGLE™ 1640M4
970-068
First, loop the pedometer clip
Next, loop the metal clip, then clasp clothing
Or, loop a  badge holder, then  put into pocket(Badge holder  not included)
Or, loop a belt  or belt loop
Eat Right! Walk More! Live Well! 
The ACCUSPLIT Lifes t yle
ACCUSPLIT EAGLE 1640M4
TW15MG
TODAYTOTALMODE
SET
RESET
MY3-WAYPYRAMID
STEPS
™
MILESKMDISTANCE
425 I 
Aqua:MODE
Cream: SET
Yellow:RESET
DISPLAY MODES
•  STEPS - TODAY: Counts steps taken since last 
 
  RESET. Reset daily to count each day’s steps.
•  STEPS - TOTAL: Keeps track of all steps taken, 
 
  even after Day’s 
STEPs are reset.
•  DISTANCE: Shows distance walked or jogged since 
 
  last reset, in miles or kilometers.
• 
 (ACTIVITY TIMER): Shows total activity time in  
  minutes and seconds since last reset. The timer runs  
  automatically whenever steps are being recorded. 
						

							
AUTO MOVEMENT SENSOR
1. To filter out random movements, the unit remains in
 
  standby mode until 5 continuous steps are registered. 
 
  Only then are the 5 steps calculated in, and an Active
 
  indicator “
▲” appears on the upper left of display.
2.  When regular walk/run movement stops, after 2 seconds 
 
  the timer pauses and the unit switches to standby status 
 
  (Active indicator “
▲” disappears). 
 
RESETTING YOUR PEDOMETER 
Most people prefer to reset step counts daily. To reset: While 
displaying Day’s STEPs, DISTANCE, or ACTIVITY TIME, press 
and hold yellow RESET button for at least two seconds to 
reset all of these to zero. When displaying Total STEPs, press 
yellow RESET button for two seconds to reset all counts, 
including Total STEPS, to zero.
REGISTER NOW Please return  your AE1640M4 Registration to  the Repair Center address in the  warranty, and we will let you know about future products. 
Email (preferred)
UserNO-PROOF-OF-PURCHASE LIMITED WARRANTY
See label inside the lid of your pedometer
REPLACING THE BATTERY
When the display starts to dim or goes blank, it is time to replace 
the battery. Your pedometer uses one Type LR43 (L1142) 1.5 volt 
alkaline battery. To replace:
1. 
Insert a coin into the slot on the bottom of the case, and twist  
  counterclockwise to loosen the case front. Lift case front away.
2. Using a pen or other thin object, push battery sideways out  
  of its holder. Replace it with a new battery. The battery’s 
 
  positive (+) terminal should be FACE UP while you put it into 
 
  the pedometer.
3.  Align case front over the pedometer and press gently to snap 
 
  cover back into place, starting with top.