Accusplit Pedometer AE140SXL User Manual

							23
4 5
67
2
Operating Instructions
ACCUSPLIT®EAGLE
AE140SXL 
PEDOMETER 
Functions•  Step  counter .
•  Automatic  Acti vity T imer .  
•  Distance  in mi or km.
F or  complete F unction Specications, go to page 31 .Key F eat ures•  Built  a ro u nd t h e J a p an ese -m ad e J W 20 0 P ed om ete rE n g in e™   
  Step S ensor, the cur rent gold standard for accuracy . 
•  Extra Large Digits. 
•  The  ACCUSPLIT  exclusive case mak es this the slimmest 
  available pedometer built around the JW20 0 Step Sensor.
•  Chromed, Spring Steel clip resists break age.
•  Case includes two leash slots, for at taching  safety leash 
  on either side. Made from tough polycarbonate plastic.  
•  Step lter , can be set from 0-5 steps to fur ther increase  
  accuracy .
HOW TO OPEN  YOUR PEDOMETER
S ee  diagrams at right.
The co ver must be closed f or the  
pedomet er to w ork.  USE IT NO W!  Your  pedometer is preset with standardiz ed set tings  
  that allow you to use it now!  You  can customiz e the  
  set tings later . Skip to pages 1 3-16 to use it now!
SET TING UP  YOUR PEDOMETER  It’s a good idea to set up your pedometer before r st using it. 
T o record your distance accurately , you will need to set your 
stride length.  
S ee  page 9 when you are ready to set up your unit.
ACCUS P
LIT EAGLE
Dig
iw a
lkerX L
.c
omS TEP   
TIME   DIS T   CA
LSET4728MOD
E
RESE
T
S3 –
S1, S2, S4 S3
+140SXL
Get ting  Acquaint ed
• Press the MODE but ton to cycle through the display   
  modes  (Steps,  Activity T ime,  …).  
  See page 20 and Specications for details.
•   The  RESET but ton sets your counts bac k to zero.  
  See page 24 for details.
MODES
•  STEP:  STEP  mode shows step count.
•   TIME:  AUT O A CTIVITY  TIMER MODE shows total  
  acti vity  time in min and sec. 
•  DIS T: DIS TANCE  mode shows distance traveled (mi/km).
STE P   TI ME     D IS T                  S ET    DIG I-WALK ERXL.C O M
140SXLS3- S3+
S1,S2,S4JW200
Mode 
indicator
Steps 
Counted
MODE But ton
RESET But ton (yellow)
ACCUSPLIT , Inc.
3090 Independence Drive, Suite 148 Livermore, CA 94551 USA
800-935-1996  •  925-290-1900  •  FAX 925-290-1930
 www .ACCUSPLIT .com  •  support@ACCUSPLIT .com
Eat R ig h t!  W alk  M ore !  L iv e W ell! 
e  A CCU SP L IT  L ife st y le970-087
Nov 07 
						

							
10
8
11
9
1213
1514
SETTING PROCEDURE
ACCUSPLIT	products	use	a	common	setting	procedure		
known	as	 “S1-	S2-S3-S4.”	Here’s	how	it	works:
Press	S1	for	2	seconds:	Enter	the	SET	mode
Press	S2:	Change	the	field	to	be	set
Press	S3:	Change	the	field	value
Press	S4	for	2	seconds:	Exit	the	SET	mode
You	can	enter	and	exit	Set	mode	from	any	of	the	regular	
display	screens.		Entering set mode 
Press	and	hold	the	S1	(MEMORY)	button	for	2	seconds.		
The	display	will	start	to	flash,	showing	that	you’ve	entered	
SET	mode.		
Setting Stride Length1.	 You	will	see	the	mode	indicator	bar	underneath	DIST		
	 and	the	 “in”	indicator	come	on.		 The	display	will	show		
	 a	flashing	number,	which	is	your	Stride	Length	set	point		
	 (in	inches).
2.	 Press	the	S3	+	(MODE)	button	to	increase	the	 Stride	
	
	 Length	(in	increments	of	¼	inch),	and	press	the	S3-		
	 (RESET)	button	to	decrease	the	Stride	Length.	Hold		
	 the	buttons	down	to	change	values	quickly.	
Finding Your Stride Length:  Your	stride	length	is	the	
length	of	one	of	your	steps,	measured	from	 “toe	to	toe.”	To	
measure,	walk	10	steps	with	your	normal	stride	and	measure	
the	 TOTAL	DISTANCE	from	the	toe	of	your	starting	step	to	
the	toe	of	your	10th	step	(see	diagram	below).	Divide	the	
TOTAL	DISTANCE	by	10,	and	multiply	the	decimal	portion	by	
12	to	find	your	stride	length	in	feet	and	inches.	Example:	 You	
walk	23	feet	and	6½	inches	in	10	steps.	Convert	to	feet	only	=	
23.542	feet	(6½	÷	12	=	0.542).	Divide	by	ten	to	get	the	stride	
length	in	feet	=	2.354	feet.	Now,	convert	back	to	feet	and	
inches	to	get	your	stride	length	=	2	feet	4.25	inches	(0.354	×	
12	=	4.25).	
10	steps
Exiting Set ModePress	and	hold	the	S4	button	for	2	seconds.	 The	unit	will	exit	
setting	mode	–	no	values	will	be	flashing	anymore.
Note: 	The	unit	will	save	any	changes	and	exit	set	mode	after	
30	seconds	unattended.
WEARING YOUR PEDOMETERGently	slide	the	pedometer	
onto	your	belt	or	the	top	
edge	of	your	pants	or	skirt.	
It	should	fit	snugly	and	
level,	above	one	knee.	 The	
strong	steel	clip	makes	it	
easy.
Note: 	The	pedometer	should	be	as	vertical	as	possible.	
Walkers	with	larger	stomachs	may	find	it	helpful	to	
wear	the	pedometer	farther	back	on	the	body,	toward	
one	hip.	
The cover must be closed for the pedometer to work. 
yes
no
To	avoid	losing	or	dropping	your	pedometer,	use	the	included	
leash	and	clip	to	fasten	the	pedometer	securely	to	your	
clothing.
Attaching the Leash1.	 Attach	the	pedometer	to	the	leash	by	looping	the	thin		
	 side	of	the	leash	through	one	of	the	leash	slots	on	the		
	 sides	of	the	pedometer	case,	near	the	bottom	of	the	unit.
2.	 Put	the	pedometer	onto	your	clothing	as	discussed	above.
3.	 Attach	the	alligator	clip	to	a	belt	loop	or	the	top	edge	of	the	
	
	 pants	or	skirt.	
Note: 		You	can	also	use	a	safety	pin	to	fasten	the	leash	to		
your	clothing,	loop	the	leash	through	your	belt	or	belt		
loop,	or	use	a	badge	holder.
First, loop leash through slot on side of pedometer
Next, clasp clothing
Or, loop a  badge holder, then  put into pocket (Badge	holder		
not	included)
Or, loop a belt  or belt loop
STEP   TIME     DIST                SETDIGI-WALKERXL.COM
140SXLS3-S3+S1,S2,S4JW200
in
Setting Stride Length
Stride	
Length	
Flashes
“in”	indicator	
for	inches 
						

							
To	replace	the	battery:
1.	 Insert	a	coin	into	the	slot	on	the		
	 bottom	of	the	case,	and	twist	to		
	 loosen	the	faceplate.	Remove		
	 faceplate	and	set	aside.
2.	Locate	the	battery	holder	as	seen	
	
	 on	sketch.	Pull	out	the	old	battery,	
	
	 and	push	a	new	LR-44	battery	into	the	holder,		
	 with	positive	terminal	(+)	facing	up.
3.	 Snap 	faceplate 	back 	into 	place, 	hooking 	the 	bottom	
	
	 two 	tabs 	first,	then	closing	by	pressing	together	at	the		
	 top	two	tabs.		
1819
1617
21
2223
VIEWING YOUR RESULTSOnce	you	put	on	your	pedometer	with	the	cover	closed,	it	
will	automatically	begin	to	record	your	steps,	activity	time,	
and	distance.	Repeatedly	press	the	MODE	button	to	cycle	
through	the	pedometer	modes:
STEPS	
g 	TIME	g 	DISTANCE	g	STEPS
Time	and	Distance	are	counted	automatically	 whenever	steps	
are	being	counted.
•	 TIME	is	time	spent	in	step	activity.
•		 DISTANCE	is	simply	stride	length	x	steps.
Note: 	For	extra	accuracy,	the	default	Step	Filter	Setting	is	1.	
See	page	19	to	learn	more.
20
RESETTING YOUR PEDOMETERMost	people	prefer	to	reset	counts	daily.	 To	reset	your	counts:	
From	STEP,	 TIME,	or	DISTANCE	mode,	press	and	hold	the	
yellow	RESET	button	for	at	least	2	seconds.	 You’ll	see	the	
values	all	go	back	to	zero.	
OTHER SETTINGS The	Step	Filter	and	Unit	of	Measurement	settings	are	
accessed	through	a	special	 “deep	set”	mode.	
To	enter	this	mode,	press	and	hold	the	S1	button	 for	4	
seconds.	 The	screen	will	display	a	single	digit.	From	within	
Deep	Set	mode,	press	the	S2	button	to	cycle	back	and	forth	
between	the	Step	Filter	set	point	and	Choice	of	Unit	System.	CHANGING STEP FILTER SETTING While	the	JW200	PedometerEngine™	Step	Sensor	is	
extremely	accurate,	some	people	like	to	have	the	ability	to	
filter	out	false	steps.		 Therefore,	the	unit	has	a	variable	setting	
step	filter,	to	allow	fine-tuning	to	your	specific	preferences.	
You	can	set	the	value	to	any	value	from	0	–	5	steps.	For	
example,	if	the	filter	is	set	to	 “3”,	the	unit	will	wait	to	start	
counting	steps	until	more	than	three	steps	have	been	taken	in	
less	than	five	seconds.	
Press	S3+	(MODE)	or	S3–	(RESET)	to	change	the	Step	Filter	
Setting.
CHANGING UNITS (English vs. Metric) The 	Pedometer 	can 	display 	either 	in 	English 	units 	(in, 	mi, 	and 	lb	
- 	this 	is 	the 	default), 	or 	in 	Metric 	units 	(cm, 	km, 	and 	kg). 	From 	within	
Deep 	Set 	mode 	(see 	pg. 	18), 	press 	the 	S2 	button 	to 	cycle 	back 	and	
forth 	between 	setting 	the 	Step 	Filter 	set 	point 	and 	Choice 	of 	Unit	
System. 	The 	unit 	will 	show 	either 	“US” 	or 	“EU” 	(for 	European 	Union)	
depending 	on 	the 	unit 	system 	chosen. 	If 	you 	change 	units 	after 	using	
the 	pedometer, 	the 	unit 	will 	convert 	all 	of 	your 	data 	into 	the 	new 	unit	
system 	when 	you 	exit 	Deep 	Set 	model. 	You 	can 	check 	to 	see 	which	
system 	of 	units 	you 	are 	using 	by 	seeing 	which 	measurement 	units	
are 	displayed 	on 	the 	Stride 	and 	Weight 	setting 	screens.
Press 	S3+ 	(MODE) 	or 	S3– 	(RESET) 	to 	change 	the 	Measurement 	Mode.	
Press 	and 	hold 	S4 	for 	2 	seconds 	to 	exit 	Deep 	Set 	Mode.
Note: 	The	unit	will	save	any	changes	and	exit	set	mode	after	 30								
	 						seconds	unattended.
REPLACING THE BATTERY AND MASTER RESETWhen	the	display	starts	to	dim	or	goes	blank,	it	is	time	to	
replace	the	battery.		
If	the	display	is	not	uniformly	dim	or	blank ,	and	appears	to	
display	 “erroneous	data”,	do	a	Master	Reset	by	pressing	all	
	
3	buttons	simultaneously	for	3	seconds	and	then	release.	
The	display	should	go	blank,	then	turn	all	segments	on,	then	
display	0	steps	in	Step	Mode.	
Note: 	All	the	settings	will	return	to	their	default	setting	values.		
If	you	need	to	change	the	battery,	the	settings	will	also	revert		
to	default	settings.
Set Step Filter set point
STEP   TIME     DIST                 SETDIGI-WALKERXL.COM
140SXLS3-S3+S1,S2,S4JW200
Set measurement mode
“US”	(English)	
or	 “EU”	(Metric) Can	be	set	
from	0-5	steps
STEP   TIME     DIST                 SETDIGI-WALKERXL.COM
140SXLS3-S3+S1,S2,S4JW200
Battery 
						

							
2627
2425
SPECIFICATIONS, FEATURES, and FUNCTIONS
Description of Functions•	 Counts	Steps	up	to	99,999	then	rollover.
•	 Counts	Time	spent	in	step	activity,	up	to	999	Min	59	sec,		
	 then	rollover.	 Automatically	counts	whenever	step	activity		
	 is	occurring.
•	 Counts	distance	traveled	during	step	activity,	up	to	
	
	 999.99	mi	or	km,	then	rollover.	 Automatically	counts		
	 whenever	step	activity	is	occurring.
•	 Adjustable	stride	length	for	greater	distance	accuracy	
	
	 (default	setting	is	21	in/53	cm,	but	can	be	set	from	12-72	in		
	 (30-180	cm),	in	0.25	in	/	1	cm	increments. •	 Adjustable	Step	Filter	(default	setting	is	1	step,	but	can	
	
	 be	set	from	0-5	steps)	to	increase	step	count		accuracy.
•	 Switchable	between	English	and	Metric	units,	without	
	
	 losing	data	(default	setting	is	English	units).
REGISTER NOW Please return  your AE140SXL Registration to  the Repair Center address in the  warranty, and we will let you know about future products. 
Email (preferred)
User
NO-PROOF-OF-PURCHASE LIMITED WARRANTYFree service for first year of ownership;  $12 fee for service thereafter. See label inside unit for date.  See www.ACCUSPLIT.com/support for details
Battery,	replacing	 . . . .22-23
Current	day’s	results,		
			viewing. . . . . . . . . . . . . .16
Setting	Mode,	exiting. . . .12
Open	your	pedometer	 . . . .4
Safety	Leash	 . . . . . . . .14-15
Setting	up	pedometer. .8-12 Step	Filter	Setting,	
	
			change	 . . . . . . . . . . .18-19
Stride	Length,		
			setting. . . . . . . . . . . . .8-12
Unit	of	measure,		
			changing. . . . . . . . . .18-21
Wearing	pedometer	 . . . . .13Warranty	 . . . . . . . . . . . . . .26
INDEX