Acco Nobo Projector S15E DLP User Manual

11 INSTALLATION
POWERING ON THE PROJECTOR
1Remove the lens cap  . 
2Ensure that the power cord and signal cable are
securely connected. The “Power/Standby” button will
flash green.
3Turn on the lamp by pressing “Power/Standby”
button on the control panel. And the
“Power/Standby” button will turn green  . 
The startup screen will display for 30 seconds.
4Turn on your source (computer, notebook, video
player ,etc.). The projector will detect your source
automatically.
2
1Turn on the projector
first and...

12 INSTALLATION
POWERING OFF THE PROJECTOR
1Press the “Power/Standby” button to turn off the projector lamp, you will see a
message “Power off the lamp?” on the on-screen display.
2Press the “Power/Standby” button again to confirm. Otherwise the message will
disappear after 5 seconds.
3The cooling fans continue to operate for about 60 seconds for cooling cycle and
the “Power/standby” button will turn orange. When the light begins flashing, the
projector has entered standby mode.
If you wish to turn the...

The projector is equipped with an elevator foot for adjusting
the image height.
To raise the projector
1
Press the elevator button .
2Raise the image to the desired height angle  , then release the button to lock
the elevator foot into position.
3Use  to fine-tune the display angle.
To lower the image
1
Press the elevator button.
2Lower the image, then release the button to lock the elevator foot into position.
3Use  to fine-tune the display angle.3
3
2
1
13 INSTALLATION
ADJUSTING THE PROJECTED IMAGE...

14 INSTALLATION
You may turn the zoom ring to zoom in or out. To focus the image, rotate
the focus ring until the image is clear. The projector will focus at distances
from 1.4 to 12.0 meters.
ADJUSTING THE PROJECTOR ZOOM / FOCUS
ADJUSTING PROJECTION IMAGE SIZE
Focus Ring
Zoom Ring
82.5cm 176.9cm 294.8cm 471.7cm 589.6cm 707.5cm
100.0cm 214.3cm 357.1cm 571.4cm 714.3cm 857.1cm
1.4m
12.0m 10.0m 8.0m 5.0m 3.0m
This graph is for 
User’s reference only
Screen 
(Diagonal)
Screen 
Size
Distance (m)Max (cm)
Min...

15 USER CONTROLS
There are two ways for you to control the functions: Remote Control and
Control Panel.
CONTROL PANEL & REMOTE CONTROL
USING THECONTROLPANEL
Power / Standby
■Refer to the “Power On/Off the Projector” section on pages 11. 
Source
■Press “Source” to choose RGB, Component-p, Component-i, S-Video, Composite
Video and HDTV sources.
Menu
■Press “Menu” to launch the on screen display (OSD) menu. To exit OSD, press
“Menu” again.
Keystone
■Adjusts image distortion caused by tilting the projector...

16 USER CONTROLS
USING THEREMOTECONTROL
Power / Standby
■Refer to the “Power On/Off the Projector” section on pages 11. 
Re-Sync
■Automatically synchronizes the projector to the input source.
Volume + / -
■Increases/decreases speaker volume.
Reset
■Changes the adjustments and settings to the factory default value. 
Mute
■Momentarily turns off the audio and video.
Keystone
■Adjusts image distortion caused by tilting the projector (±16 degrees). 
Page Up (Computer mode only)
■Use this button to page up....

17 USER CONTROLS
ON SCREEN DISPLAY MENUS
The Projector has multilingual On Screen Display menus that allow you to
make image adjustments and change a variety of settings. The projector will
automatically detect the source. 
How to Operate
1
To open the OSD menu, press “Menu” on the Remote Control or Control Panel.
2When OSD is displayed, use  keys to select any item in the main menu. While
making a selection on a particular page, press “Enter ” key to enter sub menu.
3Use  keys to select the desired item...

18 USER CONTROLS
Computer / Video Mode
LANGUAGE
Choose the multilingual OSD menu. 
■Use the  or  key to select your prefered language.
■Press “Enter” to finalize the selection.
Image-I Image-II Audio
Language Management 

19 USER CONTROLS
Computer / Video Mode
IMAGE-I
Brightness
Adjusting the brightness of the image. 
■Press the   to darken image.
■Press the   to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the amount of
black and white in the image. 
■Press the   to decrease the contrast.
■Press the   to increase the contrast. 
Colour Temp.
Adjust the color temperature. At higher temperature, the screen...

20 USER CONTROLS
Computer Mode
IMAGE-II (COMPUTER MODE)
Frequency
Frequency” changes the display data frequency to match the frequency of
your computer’s graphic card. If you experience a vertical flickering bar, use
this function to make an adjustment. 
Tracking
“Tracking” synchronizes the signal timing of the display with the graphic
card. If you experience an unstable or flickering image, use this function to
correct it. 
Horizontal Position
■Press the  to move the image left.
■Press the  to move the...