Acco Nobo Projector S11E DLP User Manual

							11 INSTALLATION
POWERING ON THE PROJECTOR
Remove the lens cap.
Ensure that the power cord and signal cables are securely
connected.
Turn on the lamp by pressing “Power/Standby” button on the
control panel. The startup screen will be displayed for 20 seconds
and the Power/Standby indicator will light solid green.
Turn on the source (computer, notebook, or video player, etc.) The
projector will detect your source automatically.
•If the projector displays “No Signal,” please make sure the      
signal cables are securely connected.
•If connecting multiple sources at the same time, use the          
“Source” button on the Remote Control or projector control   
panel to select the desired input. Press the “Source” button    
repeatedly until the desired input is displayed.
•Turn on the projector first and then the computer
1
2
3
4
Power / Standby3
Turn on the projector
first and then the
computer.
If the screen displays
“No Signal”, please
ensure the signal
cables are securely
connected.
If you connect
multiple sources at
the same time, use
the “Source” button
on the Remote
Control or Panel
Control to switch. 
						

							12 INSTALLATION
POWERING OFF THE PROJECTOR
Press the “Power/Standby” button to turn off the projector lamp. The projector will
display the message “Power off the lamp?”
Press the “Power/Standby” button again to confirm. Otherwise the message will
disappear after 5 seconds.
“Power/Standby” indicator will turn green for approximatly 90 seconds. When the
green light begins flashing, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has
completed the 90 secs cooling cycle and has entered standby mode. Once in
standby mode, simply press the “Power/Standby” button to restart the projector
Disconnect the power cord from the electrical outlet and the projector.
Do not turn on the projector immediately following a power off procedure.1
2
3
4
5
If the “TEMP” indicator turns red it indicates the
projector has overheated. The projector will
display “Over Temperature.  After a short
period the“Power/Standby” indicator will turn
green and the projector will automatically shut
itself down. If this occurs please contact your
local reseller or service center.
If the “LAMP” indicator turns red and the “Power/Standby” indicator turns
amber the projector will automatically shut itself down. If this occurs please
contact your local reseller or service center.
If the “TEMP” indicator begins flashing the projector
will display “Fan Fail” warning. After a short period
the “Power/Standby” indicator will flash green for
about 90 seconds and the projector will
automatically shut itself down. If this occurs 
please contact your local reseller or service center. 
						

							The projector is equipped with an elevator foot for adjusting the projector
height.
To raise the projector
To lower the projector
13 INSTALLATION
ADJUSTING THE PROJECTOR HEIGHT
Press the Elevator Button.
Raise the projector to the desired display angle, then release the button 
to lock the elevator foot into position.
Use the Height Adjuster Button to fine-tune height adjustment.1
Press the Elevator Button.
Lower the projector, then release the button to lock the elevator foot into
position.
Use the Height Adjuster Button to fine-tune height adjustment.1
2
3
2
3
Elevator Foot Height Adjuster ButtonElevator Button 
						

							14 INSTALLATION
To adjust the focus, simply rotate the focus ring until the image is clear. The
projector will focus at distances from 4.0 feet to 39.4 feet (1.2m to 12m)
ADJUSTING THE PROJECTOR FOCUS
ADJUSTING THE PROJECTOR IMAGE SIZE
Focus Ring
This graph is for 
User’s reference only
289.7”
237.5”
185.3”
133.8”
81.6”
29.4”
(4)
(11.1)
(18.2)
(25.2)
(32.3)
(39.4)
Screen
(Diagonal)29.4”81.6”133.8”185.3”237.5”289.7”
Screen 
Size (WxH)23.5 x 17.7”65.3 x 48.9”107.1 x 80.3”148.2 x 111.2”190.0 x 142.5”231.8 x 173.8”
Distance4.0’11.1’18.2’25.2’32.3’39.4’ 
						

							15 USER CONTROLS
There are two ways for you to control the functions: Remote
Control or Panel Control.
PANEL CONTROL & REMOTE CONTROL
Remote Control
Panel Control
Power / Standby
■Refer to the Power On / Off the Projectorsection on page 11. 
Optimum Setting
■PressOptimumto select Conference Mode or Cinema Mode.
Source
■PressSourceto cycle between VGA, S-Video, Composite, 
and Component sources
1. Power Indicator Light
2. Power / Standby
3. Re-sync
4. Menu/On/Off/Enter5. Four Directional Select Keys
6. Source
7. Temperature Warning LED
8. Lamp Warning LED
1 23
45
678
1
2
3
4
5
6
7
8
9
10
11
12
13
1. Power / Standby
2. Page Up 
3. Multi-Directional 
Selector
4. Source 
5. Re-sync 
6. Keystone Correction
7. LED
8. Optimum Setting
9. PageDown
10.Menu
11. Freeze
12.Hide
13.Zoom In / Zoom Out 
						

							16 USER CONTROLS
Multi-Directional Selector
■These keys are used to control the direction  operation on the OSD display.
Page Up (Computer Mode only)
■Use this button to page up. This function is only available when the projector is connected 
to a computer via a USB cable.
Page Down (Computer mode only) 
■Use this button to page down. This function is only available when the projector is 
connected to a computer via a USB cable.
Menu
■Press “Menu” to open the OSD menu and press   key to select menu items. To exit the OSD, 
press the “Menu” button again. The projector will automatically save any changes made.
Freeze
■Press the “Freeze” button to pause the screen image
Ke K e ystone + / -
■Adjusts image distortion caused by tilting the projector. (± 16 degrees)
Zoom In
■Press “Zoom In” to magnify an image by a factor of eight times on the projection screen.
Zoom Out
■Press the “-” zoom button to zoom out of the image. The smallest setting available is 1/2-size
Resync
■ When the “Resync” button is pressed, the projector will automatically synchronize with 
the source signal.
Hide
■ Pressing the “Hide” button, will turn the entire screen black, a useful function for
speakers who require a short pause in order to change their presentation materials.
Use the Remote Control
Power/Standby
■ Refer to the ‘Power On/Off the Projector” section on pages 12.
Source
■ Press “Source” to cycle through VGA, S-Video, Composite and Component sources.
Re-Sync
■ Automatically synchronizes the projector to the input source.
Four Directional Select Keys
■ Use to select items or make adjustments for your selection.
Enter
■ Confirm your selection of items.
■ Press “Menu” to open the OSD menu and press   key to select menu items. 
To exit the OSD, press the “Menu” button again. The projector will automatically
save any changes made. 
						

							17 USER CONTROLS
ON-SCREEN DISPLAY MENUS
How to Operate
■The projector has multilingual OSD menus that allow you to make image
adjustments and change a variety of settings. With a computer source, the OSD
displayed is the “Computer OSD”. With a video source, the OSD display is the
“Video OSD” The projector will automatically detect the source.
■To open the OSD menu, press the “Menu” button on the remote control or 
panel control.
■When the OSD is displayed, press   key to select main items.
E.g.: Image-I >Image-II>Language>Management>Image-I...
While making selection on a particular page, press key to go into sub-menu.
■Press  key to select the required item and adjust the settings by  key.
When a specified item is selected, the colour of the item will change
from yellowish brown to blue.
E.g.: Brightness >Contrast>Colour Temp. >Zoom>Keystone>White Segment >
Brightness...
■When using the  keys to adjust parameters or select required sub menu
functions, confirm selections/modifications by pressing the “Enter” button. Pressing
the “Enter” button to confirm a selection/modification will revert the OSD back to
the main menu. Only the  keys are enabled now.
■To exit the OSD, press the button again. 
						

							18 USER CONTROLS
Computer Mode
IMAGE-I
(COMPUTER MODE)
Brightness
Adjusting the brightness of the image. 
■Press the       key to darken the image.
■Press the       key to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the amount of
black and white in the image.
■Press the       key to decrease the contrast.
■Press the       key to increase the contrast.
Colour Temperature
Adjust the colour temperature. The range is from “0”to “4” The factory
default is “2”. With the higher temperature, the screen looks colder; with the
lower temperature, the screen looks warmer.
Zoom
■Press the  to magnify an image up to a factor of eight times on the 
projection screen.
■Press the  to Diminish the zoom in image. Lowest available setting is 1/2-size.
Keystone (Keystone Correction)
Adjust image distortion caused by tilting projection. (±16 degrees) 
White Segment
Use the white segment control to set the white peaking level of the DMD
chip.”0” stands for minimal peaking, and “10” stands for maximum peaking.
If you prefer a stronger image, adjust toward the minimum setting. For a
smooth and more natural image, adjust toward the minimum setting. 
						

							19 USER CONTROLS
Video Mode
IMAGE-I
(VIDEO MODE)
Brightness
Adjusting the brightness of the image. 
■Press the key to darken the image.
■Press the key to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the amount of
black and white in the image.
■Press the key to decrease the contrast.
■Press the key to  increase the contrast.
Colour
The colour setting adjusts a video image from black and white to fully
saturated colour.
■Press the key to decrease the amount of colour in an image.
■Press the key to  increase the amount of colour in an image.
Tint
The tint adjusts the colour balance of red and green. 
■Press the key to increase the amount of green in the image.
■Press the key to  increase the amount of red in the image.
Sharpness
Adjusting the sharpness of the image. 
■Press the key to decrease the sharpness.
■Press the key to  increase the sharpness.
White Segment 
Use the white segment control to set the white peaking level of DMD chip.
“0” stands for minimal peaking, and “10” stands for maximum peaking. If
you prefer a stronger image, adjust toward the maximum setting. For a
smooth, more natural image, adjust toward the minimum setting.  
						

							20 USER CONTROLS
Computer Mode
IMAGE-II
(COMPUTER MODE)
Frequency
“Frequency” is for changing the display data frequency to match the
frequency of your computer’s graphic card. When you experience a vertical
flickering bar, use this function to make an adjustment.
Tracking
Choose “Tracking” item to synchronise the signal timing of the display with
that of the graphic card. When you experience an unstable or flickering
image, use this function to correct it.
Aspect Ratio
You can use this function to fit your desired aspect ratio.
Horizontal Position
■Press the       to move the image left.
■Press the       to move the image right.
Vertical Position
■Press the       to move the image up.
■Press the       to move the image down.
Reset
Choose “Yes” to return the display parameters back to the factory default.Reset:
Reset select includes
both Image-I and
Image-II settings