Acco Nobo Digital DLP Projector X25C User Manual

  maximum peaking.  If you prefer a stronger image, adjust towards  
  the maximum setting.  For a smooth and more natural image,  
  adjust towards the minimum setting.
 Colour Temp.
Adjust the colour temperature. At a higher temperature, the screen  
  looks colder; at a lower temperature, the screen looks warmer. 
21
... English
User Controls 

Image-II
(Computer Mode)
 Frequency
  “Frequency”changes the display data frequency to match the  
  frequency of your computer’s graphic card. If you experience a  
  vertical flickering bar, use this function to make an adjustment.
 Tracking
  “Tracking” synchronises the signal timing of the display with the  
  graphic card. If you experience an unstable or flickering image, use  
  this function to correct it.
  H.Position (Horizontal Position)

Press the  to move the image left. 
Press the  to move...

  16:9 Image Position
Adjust the image position to up or down, when you select the    
  aspect ratio to 16:9.
Press the 
 to move the image down.
Press the  to move the image up.
Window Original Pixel
 16:9 Image Position: 


Image Position at win-
dow mode will also be
moved accordingly.
23
... English
User Controls 

User Controls
Image-II
(Video Mode)
 Degamma
  This allows you to choose a degamma table that has been fine- 
  tuned to bring out the best image quality for the input.
 Saturation
Adjusts a video image from black and white to fully saturated  
 colour.
  Press the 
 to decrease the amount of colour in the image.
Press the 
 to increase the amount of colour in the image. 
 Ti n t  
Adjusts the colour balance of red and green.
Press the 
 to increase the amount of green in the image.
Press the 
 to...

  16:9 Image Position
Adjust the image position to up or down, when you select the    
  aspect ratio to 16:9.
Press the 
 to move the image down.
Press the  to move the image up.
Window Original Pixel
16:9 Image Position: 
Image Position at win-
dow mode will also be
moved accordingly.
25
... English
User Controls

 

 Security Settings
  A. Press “Enter” to set password. (First time)
  1.  Password must be 4~8 bits, the default value is “0000”. 
  2.   Displayed on the screen by “*” while inputting. 
 3.  Use 
 keys to select your input bits, and then press  
    “Enter” key to confirm your selection.
  4.   Move to 
 and then press the “Enter” key to confirm finally.
  5.   On this screen, press the “Menu” key which will automatically 
    jump to           then press the “Enter” key to confirm your selection.  
(“Menu”...

  1.  Input the old password.
  2.  Changes a new password. 
  3.  Confirms the password, please input the new password once  
 again.
  4.  Password must be 4~8 bits, Default value is “0000”. 
  5.   Displayed on the screen by “*” while inputting. 
 6.  Use 
 keys to select your input bits, and then press  
    the “Enter” key to confirm your selection.
  7.   Move to 
 and then press the “Enter” key to confirm finally.
  8.  On this Screen, press the “Menu” key to switch between the  
  position at present...

 Lamp Hours
Display the cumulative lamp operating time.
 Lamp Reset
Reset the lamp life hour after replacing a new lamp. 
 Lamp Reminding
Choose this function to show or to hide the warning message when 
the changing lamp message is displayed. The message will show up 
30 hours before end of life.
 ECO Mode
Choose “On” to dim the projector lamp which will lower power 
consumption and extend the lamp life by up to 130%. Choose ”Off” 
to return to normal mode.
  Auto Power Off (min)
Sets the interval of...