Aaxa Projector P300 Pico Projec User Manual

aaxa
TECHNOLOGIES
User Guide
 P3OO  Pico Projec- 

Caution!
WARNING:  Please use this product as instructed.  Misuse may cause 
injury or death.
DO NOT use while driving
DO NOT expose to water or wet 
surfaces.  Electric shock may occur.
DO NOT expose the projected LED 
image to your eyes or the eyes of 
others
 
DO NOT block or restrict airflow 
from ventilation holes as this may 
cause the projector to overheat
Keep the projector, battery, or  
charger away from any heat sourcesCaution for Battery Use
• Do not pierce or puncture the battery 
with sharp...

Table of Contents
Chapter 1: P300 at a glanceMain Unit Front/Back
Remote & Keypad
Accessories 
Chapter 2: Getting Started Powering On / OFF
Focus Adjustment  / Throw 
Distance
Battery Installation
Connecting to a Computer VGA
Connecting to a Computer HDMI
Connecting to Composite Video
Connecting to HDMI Video
Connecting to Speaker or Head -
phones
1
2
3
4
5
6
7
8
10
12
14
16 17
19
21
22
24
25
27
28
30
31
32
37
39
40
41Connecting a Micro SD Card
Connecting to a USB Host
Chapter 3: Menu Screens Main menu...

P300 at a Glance
2
Chapter 1
Power On/Off
 
Main Menu  NavigationPower Switch
Micro SD Card
Headphone Out USB Port
Main Unit Front/Back
VGA Port AV Input
Power Button
DC Adapter  Port
HDMI
Focus Adjustment 

PWRGamma
M
ENUUUPEXIT
VOL-
OKVOL+
I
U/D DOWN R/L
VGA Menu
AV
Menu
Remote & Keypad
3
NOTICE: Pressing power on the remote will only put the projector in  STANDBY 
mode.  Please press the power button on the projector if you want to tur\
n it off.
Power On/Off
 
Main Menu  Navigation Select Source
Media Pl
ayer Menu 
Navigation
Input Exit/Back
Direction Pad
Both the keypad and remote can be used to navigate through the menus.  The Main Menu 
Navigation on the remote functions exactly the same as the...

Accessories
4
*Under various circumstances, the actual accessories may be different from 
those shown in the pictures above.
TripodRemote
Power Adapter VGA Cable
A/V Cable
PWRGamma
MENUUUPEXIT
VOL-OKVOL+
I
U/D DOWN R/L
VGA Menu
AV
Menu
Internal Battery   (sold separately) 

Getting Started
1. Connect the power cord to the P300.2. Connect the wall plug into the wall power source.3. Switch the On / Off switch on the side of the projector to the “ON” position to ente\
r 
“standby” mode
4. Press POWER button on the keypad and hold for 2-3 seconds to start the p\
rojector
5
Powering ON the projector
Chapter 2
Powering OFF the projector
1. Press and hold the power button on the keypad for 3 seconds.2. The optical engine should power off and the fan should stop spinning.  The...

Focus Adjusment / Throw Distance
Focus Adjustment
• Spin the focus wheel up or down until the image becomes 
clear.
6
DIAGONAL SCREEN SIZE
16:9 Aspect  Ratio
Throw Distance Chart
Distance inch (“)
20
30
40
50
60
70
80
90Diagonal Inch (“)
17
25
34
42
51
59
68
76
Throw Ratio 1.38
*minimum throw distance: 10 inches 

Installing the Battery Pack
7
1. Remove the three screws circled in blue holding 
the P300 battery.
2. Connect the battery harness to the battery recep-
tacle on the PCBA
3. Install the new battery housing 

Connecting to a Computer via VGA
Connect the large end of the 8
VGA Cord
to your computer’s
VGA Adapter
Connect the small end of theVGA Cordto your P300’s 
VGA Adapter
Step 1:
Step 2:
Step 3:
In the Main Menu 
Select “VGA” icon 
Select “INPUT” icon