A&D Balance SCE02 User Manual

							SCE-02    USB Interface Instruction Manual
 
 1. Features 
•   Connects a scale to a personal computer and used to transmit the scale weight data to the 
personal computer via USB. Applicable OS is Windows 98SE or later. 
•  As a standard Windows driver is used, complicated installation of a dedicated driver is not 
necessary. Once a connection between the scale and the personal computer is made, the weight 
data can be transmitted. 
•   Transmits the scale weight data to any application such as Excel, Word or memo pad for Windows. 
Notes: • Only the weight data can be transmitted. Headers and units can not be transmitted. 
• Data transmission from the personal computer to the scale is not available. If it is 
necessary to control the scale by a command, connect the scale and the personal 
computer using the SCE-03 RS-232C serial interface. 
• SCE-02 and SCE-03 can not be installed at the same time
. 
• Turn off the screen saver or suspend mode of the personal computer. 
• Windows, Word and Excel are the registered trademarks of the Microsoft Corporation. 
   2. Installation Procedure 
Note:  Before installing the SCE-02 board, be sure to remove 
the batteries from the scale. 
 
Step 1  Hold the board in such a way that its USB mini port will 
match the hole on the casing. Insert the board into the 
casing by sliding it into the casing groove. 
Step 2  Place the waterproof packing on the casing, aligning its 
holes with the casing screw holes. 
Step 3  Remove the four screws on the option slot panel located 
on the bottom of the display. 
Step 4  Insert the board into the option slot. 
Step 5  Secure the casing to the display, using the four screws provided 
with the casing. 
Step 6   Seal the screw heads with the tabs attached to the 
waterproof packing.  
Step 7  Insert the USB mini-B cable (sold separately), into the port 
at the rear of the casing. 
 3. How to use 
Step 1    Turn the personal computer on to start up Windows. And then, insert 
the batteries into the scale and turn the scale power on. 
Step 2     Connect the scale to the personal computer, using the USB cable
. 
Note:  When connecting the USB cable, be sure that the scale data output mode is 
set to a mode other than stream mode. 
Step 3    For the first installation, the driver will be installed. For details, refer to “4. 
Installation of the Standard Windows Driver”. For the second installation or 
after, this step is not required. 
Step 4    Start up the application (such as Excel) into which the scale weight data is transmitted. 
                 Place the cursor in the position to enter the scale weight data. 
Step 5    Press the scale PRINT key. The weight data is input at the cursor position. Step 6    To finish the operation, disconnect the USB cable.。 
4. Installation of the Standard Windows Driver 
• Windows 2000 / Me / XP 
Once connected, an automatic driver installation will start. Wait for the installation to complete. 
• Windows 98 
Step 1  The “Add New Hardware Wizard” window 
appears. 
  Click on “Next”. 
 
 
 
 
 
 
Step 2  Check “Search for the best driver for your 
device (Recommended).” and click on 
“Next”.  
 
  
  
 Step 3  Uncheck all the items and click on “Next”.  
 
 
 
  
  
 Step 4  Make sure that “USB Human Interface 
Device” is displayed and click on “Next”.  
   
 
 
 
 
 Step 5  Driver installation has started. When 
completed, the window shown to the right 
appears. 
     Click on “Finish”
 
 
Note:  During installation, a message requesting to 
insert the Windows 98 CD-ROM may appear. 
    In this case, insert the Windows 98 CD-ROM 
and click on “OK”.
 
 
Waterproof 
packing 
Seal the screw heads USB mini
port 
CasingScrews on 
the option slo
t
USB mini-B
cable 
3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo  170-0013  JAPAN 
Telephone: [81] (3) 5391-6132  Fax: [81] (3) 5391-6148