3M Super Close Projection System SCP716 Operators Guide

							11 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
D CAUTION
To reduce the risk associated with intense visible light:
Avoid looking directly into the projector lens while the lamp is on. s
To reduce the risk associated with impact of a falling projector:
Use only the 3M brand wall/ceiling mounting hardware kit if wall or ceiling mounting is desired. s
Installation of the 3M brand wall/ceiling kit must only be performed by qualified personnel. s
Adhere strictly to the proper installation procedure as outlined in the installation instructions when  s
installing the 3M Wall/Ceiling kit.
Always operate the unit on a flat and sturdy surface. s
To reduce the risk associated with explosion, and/or chemicals from leaking battery:
Use only with battery type AAA. s
Orient the battery’s plus (+) and minus (-) terminals according to the markings found on the remote  s
control.
Do not leave the battery in the remote for an extended period of time. s
Do not heat, disassemble, short, recharge, or expose the batteries to fire or high temperature. s
Do not carry batteries loose in your pocket or purse. s
Avoid eye and skin contact in the event that battery would leak. s
Do not mix used and new batteries. s
To reduce the risk associated with tripping, and/or impact:
Position the power cord and cables so that they can not be tripped over. s
To reduce the risk associated with environmental contamination:
Dispose of mercury lamp, exhausted batteries, and other electronic components in accordance with  s
applicable federal, state and local regulations.
To reduce the risk associated with hot surface of lamp cartridge:
Before replacing the lamp, allow the lamp to cool for 60 minutes and then unplug the projector  s
from the electrical outlet.
To reduce the risk associated with environmental contamination due to mercury:
Hg: Lamp contains mercury. Don’t throw in trash. Dispose according to local, state, or federal laws.  s
See www.lamprecycle.org or call 1-800-328-1371.
SAVE THESE  INSTRUCTIONS 
						

							12 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Safety Labels
The following safety labels are used on this product. 
						

							13 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Contents of Shipping Box
This projector is shipped with the necessary cables required for standard DVD player, PC or laptop computer 
connections. Carefully unpack and verify that you have all of the items shown below. If any of these items are 
missing, please contact your place of purchase.
The shipping carton contains the following items illustrated below. If any of these items are missing, please 
contact your place of purchase.
1. Projector
2. Remote Control Transmitter (AAA batteries included)
3. VGA to VGA cable, 1.8m (15-pin Male)
4. Power cord
5. Operator’s Guide CD
6. USB A-B cable, 1.8m (not shown)
           1                  2             3
       4                   5
Keep Your Packing Materials
Save the shipping box and packing materials in the event this product should require shipping to a 3M Service 
Center for repair. Use packing material to protect projector.
What’s Next?
Take a few minutes to review the machine characteristics before you setup and operate the projector. We hope 
you will enjoy using this high performance product in your classrooms, presentations and training sessions. This 
product has been produced in accordance with 3M’s highest quality and safety standards to provide smooth and 
trouble-free use in the years to come. 
						

							14 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Product Description
The 3M SCP716 integrates short-arc lamp and Digital Light Processing™ (DLP) technology. It accepts input 
from computer and/or video sources and projects a bright image through 3M™ Vikuiti™ Super Close Projection 
technology.
Machine Characteristics
The 3M SCP716 offers the following features:
Native Resolution 1024 x 768 XGA s
On-screen menu with 9 languages (English, French, Deutsch, Spanish, Italian, Japanese, Chinese Traditional,  s
Chinese Simplified, Korean)
Lamp Life of 5000 hours (ECO mode) s
Lamp Life of 2000 hours (Bright mode) s
Brightness: 2000 lumens typical (normal mode) s
Brightness: 2400 lumens typical (bright mode) s
Image size: 50 to 85 inches s
Aspect Ratio: 4:3 s
Digital keystone correction s
Security Lock s
RS232 Control capable s
3M Super Close Projection technology s
Dimensions
1.9 in.
47.5 cm5.0 in.
126.6 cm
2.5 in.
63.4 cm
2.6 in.
65.1 mm
2.1 in.
54.0 mm
2.7 in.
68.0 mm
4.6 in.
116.2 cm
3.3 in.
82.639 cm
10.2 in.
359.1 cm
12.9 in.
326.6 cm 
						

							15 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Projector Distance from Screen and Image Size
Refer to the chart below for the projector-to-screen distance and corresponding projected image size values.
Image Size Distance (D) Offset Min (S) Offset Max (S)
Diagonal Width Height (H) in mm in mm in mm
50 40 30 24 3/4 629 1 1/4 30 2 3/4 69
60 48 36 29 3/4 755 1 2/4 37 3 1/4 82
70 56 42 34 5/8 880 1 3/4 43 3 3/4 96
75 60 45 37 1/8 943 1 3/4 46 4 103
80 64 48 39 5/8 1006 2 49 4 1/4 110
85 68 51 42 1/8 1069 2 52 4 2/4 117
Vertical Lens Shift
The lens-shift feature will vertically offset the picture from 1¼ in. (30 mm) up to 4 ½ in. (117 mm) 
depending on the projector-to-screen distance and size of the projected image. This adjustment is 
typically used with wall mount applications as a fine-adjustment to the vertical position of the projected 
image. Turn the adjustment screw to vertically raise or lower the physical position of the lens. Refer to 
the chart above for the offset values.
Note: The Lens-Shift adjustment screw does not adjust or change any keystone properties.
D
2-1/2 in.(63mm)
H
S 
						

							16 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Parts Identification
1. Super Close Projection Lens
2. Focus Adjustment
3. Lens-shift
4. Remote Control IR Sensor
5. Status Indicator Light
6. Standby/On Button
7. Lamp Cover
8. Ventilation Slots
9. Control Input
10. Computer/Component Input
11. Slot for Kensington™ Lock
12. USB Port (For remote mouse functionality)
13. AC Power Cord Connection
14. Height Adjustment Foot
1
1312
11
109 234
56
147
8
Projector Terminal  Connections
1234
AC Power
USB
Computer
I/O Module Control
# Projector Panel Function
1 A/C Power Connect AC power cord to projector.
2 USB Connect projector USB (B-type) to computer USB port to control computer 
pointer with remote control.
3 COMPUTER Input VIDEO signal from a computer source.
4 I/O Module Control Connect projector control port to computer serial port with RS232 adapter or 
the 3M I/O Module and control the projector. 
						

							17 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
I/O Module Control Panel (optional accessory)
If your projector has the optional I/O Module installed, the projector functions can be operated from the I/O 
Module Control Panel.
435612
# I/O Module Control Panel Function
1 ON/OFF Turns the projector on and off
2 Volume +/- Increases (+) or decreases (-) audio level
3 Source Switches the displayed input source. Switching order: Computer 1 => 
Computer 2 => S-Video => Video
4 Menu Displays the projector’s menu system.
5 Arrow Buttons Navigate up/down or left/right through projector’s Menu system.
6 ENTER
(Center of Arrow buttons)Select menu item and confirm menu selections
Top Terminal Panel on I/O Module
Use the Top Terminal Panel to connect the projector to the I/O Module box.
I/O Module3 145
2
Audio
Power
USB         USB 
Control                     Signal 
To ProjectorAudio
Out
# Top Terminal Panel Function
1 Audio Power Relay Audio power (from bottom terminal) through to speaker 
amplifier.
2 USB (Hub) Connect two USB devices (like the projector’s remote mouse) to a 
single USB port on computer connected to the I/O Module’s bottom 
terminal panel.
3 CONTROL Connect IO/Module to projector I/O Module CONTROL terminal.
4 Signal Connect I/O Module to projector COMPUTER port.
5 Audio Out Connect IO/Module to external speakers or speakers in 3M Folding 
Wall Mount FWMSV2. 
						

							18 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Bottom Terminal Panel on I/O Module
Use the Bottom Terminal Panel to connect the I/O Module box to the Computer/Video source.
I/O Module
78910 11 12 13
12 3456
# Bottom Terminal Panel Function
1 Audio Power Supplies power to 3M Folding Wall Mount speakers from the power 
supply included with the 3M Folding Wall Mount.
2 Computer2/Component2 Input for computer or component video device.
3 Serial RS-232 Passes control commands from a computer or control system to the 
projector.
4 Video Input for composite video devices.
5 RCA Input R/L Right and Left Channel Audio Input.
6 Stereo Mini 2 Stereo Audio input for Computer2.
7 USB Connects the two devices connected to the top terminal panel USB ports 
to a computer.
8 Ethernet Allow access to the projector control webpage and control command 
over a network remote monitoring & control.
9 Computer1/ Component1 Input for computer or component video device.
10 Computer Out Output the signal from the Computer 1 port.
11 S-Video Video device input for S-video
12 Stereo Mini 1 Stereo Audio input
13 Audio Out Connects selected audio input to active speakers or audio amplifier. 
						

							19 Operator’s Guide 3M
™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Remote Control Functions
Aim the remote control toward the projection screen or at the IR sensor on the front of the projector. Press 
desired remote control button to send a signal to the projector.
 Trigger button is
       bottom of remote
ON/STANDBY ON: Press to turn projector ON.
OFF: Press to display confirmation message, press 
again to switch projector to Standby mode.
Note: The confirmation message displays to ensure 
unit does not get turned off accidentally.
INPUT/ SOURCE Press for current input source.  Press again to select 
different computer/video input.
[Computer 1/Componet 1 –> Computer 2/Componet 2 
–> RCA Composite Video –> S-Video]
Volume +: Press to increase speaker volume.
Volume –: Press to decrease speaker volume.
Mute: Press to switch the audio sound ON or OFF.
Menu: Press to display the Main Menu.  When a menu is 
open, press to exit menu.
R/Click Performs remote Right Mouse click function (when 
USB is connected to projector USB).
Up Arrow Moves cursor upward through menu items.
Down Arrow Moves cursor downward through menu items.
Left Arrow Moves cursor left through menu items. Moves .ppt 
slides backwards.
Right Arrow Moves cursor to right through menu items. Moves .ppt 
slides forward.
Mouse Pad Allows remote mouse functions. Allows Pan function 
when in Zoom mode.
Blank: Press to replace projected image with black image. 
Press again to return projection image.
Freeze: Press to freeze current image. Press again to return to 
active image.
Timer: Press to initiate a 10:00 minute digital timer.  Press 
up/down arrows to change timer clock by 1 minute 
intervals up to 99:00.
Zoom +: Press and hold to increase the size of the displayed 
image up to 200 percent.
Zoom -: Press and hold to decrease size of the displayed image 
down to 100 percent
Bottom Trigger Pull trigger for remote LEFT mouse button functions.  
In menu mode, use for remote Enter / Select functions. 
						

							20 Operator’s Guide
3M™ Super Close Projection System SCP716
© 3M 2009. All Rights Reserved.
ENGLISH
Installing Batteries in Remote Control
1. Push down on cover to unlatch it. Slide cover off.
2. Install new AAA batteries with the correct polarities.
3. Reinstall battery cover.
Note: Verify the battery cover is fully latched before 
using the remote control.
Setup and System Configuration