3M Personal Projector Mp8747 Operators Manual

113M™ Personal Projector MP8746/MP8747
© 3M IPC 2000
System Setup—Connecting to Various Equipment (continued)
Cable Connections
RGB Signal input (video from computer)
Connect one end of the enclosed RGB cable to the RGB IN 1 or 2 terminal of the projector. Connect the
other end to the RGB signal output or RGB OUT of the computer.
 Note: For Macintosh computers, the optional Mac adapter is necessary.
Please consult your dealer to order one, if necessary. Ordering
information is on page 30.
Audio signal...

3M™ Personal Projector MP8746/MP874712© 3M IPC 2000
STANDBY/ON
Press STANDBY/ON button to
begin projection mode (lamp on)
or press and hold button for one
second to switch to standby
mode (lamp off).
BLANK
Press to turn ON/OFF the
screen blanking function.
DISK PAD
Press to operate the mouse
shift function and left-click
function.
*AUTO
Press to make projector automatically
adjust 4 items (V. POSIT, H. POSIT, H.
PHASE, and H. SIZE) for RGB input signal.
(Please see note at bottom right.)
MENU
Press to...

133M™ Personal Projector MP8746/MP8747
© 3M IPC 2000
Changing Remote Control Battery
When remote control transmitter becomes difficult to operate or does not respond, it usually needs new
batteries.
1. Turn over the remote control transmitter to access the battery holder.
2. Push the battery cover tab as indicated and lift up to remove it.
3. Lift old batteries out of compartment.
4. Replace with two AA batteries. Make sure the positive (+) and negative (-) terminals are correctly
oriented.
5. Place...

3M™ Personal Projector MP8746/MP874714© 3M IPC 2000
The mouse type and cable type are determined by the type of computer used. Use the table shown below to
select the appropriate cable or refer to your computer’s user manual. Connect as shown in the diagram.
Remote Control Mouse Function
For PS/2, ADB (Mac), Serial
1. Turn off the computer and use the appropriate cable to connect the computer to mouse unit.
2. Turn on the computer and use the mouse function of the remote control. If there are any...

153M™ Personal Projector MP8746/MP8747
© 3M IPC 2000
Attaching the Handle
Section 2: Product Description
Attach the enclosed handle to the projector for easier carrying and portability.
1. Raise the handle hooks on the right side of the projector.
2. Insert one end of the handle strap through the handle hook.
3. Thread the end of the strap through the buckle as shown.
4. Repeat for the opposite end of the handle strap.
Caution
•Make sure the handle is securely attached before lifting or carrying. If the...

3M™ Personal Projector MP8746/MP874716© 3M IPC 2000
1. Press and hold the STANDBY/ON button        for approximately two  seconds. The ON indicator
blinks orange and the lamp turns off. After approximately one minute, the fan stops and the indicator
stays orange.
2.Turn off the MAIN POWER SWITCH.
3.Close the sliding lens door.
Caution
Projector Start-up
Section 3: Basic Operations
Figure 3.1 Projector Controls
1. Make all equipment and cable connections with the power off.
2. Turn on the MAIN POWER...

173M™ Personal Projector MP8746/MP8747
© 3M IPC 2000
How to Use Height Adjustment Foot
Section 4: Adjustments and Functions
Adjust the image elevation and projection angle (within 0 to 9°) using the height adjustment foot at the front
of the projector and the tilt adjustment knob at the rear of the computer.
1. Raise the front end of the projector so the foot is not touching the tabletop.
2. Push the lock button on the left side of the projector to unlock the foot.
3. Extend or retract the foot to the...

3M™ Personal Projector MP8746/MP874718© 3M IPC 2000
Section 4: Adjustments and Functions
Plug & Play Function
Plug & Play is a system configured with peripheral equipment (including a computer and display), and a
compatible operating system. This allows the user to connect various peripheral equipment successfully
without having to adjust settings manually. The equipment and projector exchange this information automati-
cally. This projector is VESA DDC (Display Data Channel) 1/2B compatible. Plug & Play...

193M™ Personal Projector MP8746/MP8747
© 3M IPC 2000
Section 4: Adjustments and Functions
Menu Navigation
Factory Default Setting:
To reset a single item from SETUP menu:
1. Select the adjustment item (Bright, Contrast...).
2. Press the RESET button.  Only the selected item
resets. 1. Press MENU DISK button on projector or remote control MENU buttons.
On-screen menus are displayed on the projected image.
2. Select the menu to be adjusted by pressing the right or left arrows on the MENU DISK buttons or...

3M™ Personal Projector MP8746/MP874720© 3M IPC 2000
Section 4: Adjustments and Functions
Figure 4.6 RGB signal input Figure 4.7 Video signal input
*Auto Sync Function: Press the AUTO button on the remote control to engage the automatic sync function.
The message “AUTO IN PROGRESS” will display for several seconds as the projector adjusts the V. POSIT,
H.POSIT., H.PHASE, and H. SIZE settings. Auto Sync can also be executed from the control panel key pad.
Press and hold the RESET button, then press the...