3M Multimedia Projector X68 Operators Manual

31

Multifunctional settings
INPUT Menu (continued)
ItemDescription
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. It shows the information about the current input.
INPUT-INFORMATIONRGB1024x768 @60.0FRAME LOCK
INPUT-INFORMATIONS-VIDEOSECAMAUTO
INPUT-INFORMATIONCOMPONENT576i @50SCAR T RGB
• The “FRAME LOCK” message on the dialog means the frame lock function is working. This function automatically works when a RGB signal with vertical frequency of 50 to 60 Hz is input, and...

32

Multifunctional settings
SETUP Menu
ItemDescription
WHISPER
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL 
 WHISPER
• When the WHISPER is selected, acoustic noise and screen brightness are reduced.
MIRROR
Using the buttons ▲/▼ switches the mode for mirror status.
NORMAL   H:INVERT  V:INVERT  H&V:INVERT 
VOLUMEUsing the buttons ▲/▼ adjusts the volume.
High  Low
AUDIO
Choose an input port using the buttons ▲/▼ 
(1), then select the audio port to be interlocked 
with the input port...

33

Multifunctional settings
SCREEN Menu
ItemDescription
LANGUAGE
Using the buttons ▲/▼ switches the OSD (On Screen Display) language.
SUOMI  POLSKI  TÜRKÇE
ENGLISH  FRANÇAIS  DEUTSCH  ESPAÑOL  ITALIANO
NORSK  NEDERLANDS  PORTUGUÊS  日本語
                 SVENSKA 
MENU POSITIONUsing the buttons ◄/►/▲/▼ adjusts the menu position.
To quit the operation, press the MENU button on the remote control 
or keep no operation for 10 seconds.
OSD BRIGHT. Using the buttons ▲/▼ switches the 
brightness...

34

Multifunctional settings
ItemDescription
START UP
Using the buttons ▲/▼ switches the mode for the start-up screen.The start-up screen is a screen displayed when no signal or an unsuitable signal is detected.
MyScreen   ORIGINAL  TURN OFF
    
MyScreen is a screen you can register as a desired screen.The 
ORIGINAL screen is the existing standard screen. When TURN 
OFF is selected, the BLACK screen is used.
• 
To avoid remaining as an afterimage, the MyScreen and the 
ORIGINAL screens will change to...

35

Multifunctional settings
ItemDescription
MESSAGE
Using the buttons ▲/▼ turns on/off the message function.
TURN ON  TURN OFF
When the TURN ON is selected, the following message function 
works. “AUTO IN PROGRESS” while automatically adjusting
”NO INPUT IS DETECTED”
”SYNC IS OUT OF RANGE”
"Searching….” while searching for the input”Detecting….” while an input signal is detectedThe indication of the input signal displayed by changing The indication of the aspect ration displayed by changingThe...

36

Multifunctional settings
OPTION Menu
ItemDescription
AUTO SEARCH
Using the buttons ▲/▼  turns on/off the automatic signal search  function.
TURN ON  TURN OFF
This function works with INPUT, RGB, and VIDEO buttons.
When the TURN ON is selected, detecting no signal automatically 
cycles through input ports in the following order . The search is started from the current port. Then when an input is found, the projector will stop searching and display the image. RGB IN1  RGB IN2  COMPONENT VIDEO ...

37

Multifunctional settings
ItemDescription
SERVICE
Selecting this item displays the SERVICE menu.Select an item using the buttons ▲/▼, and press the button ► or the ENTER button on the remote control to execute the item.FAN SPEED   AUTO ADJUST   GHOST  KEY LOCK  FILTER MESSAG  FACTORY RESET       FAN SPEEDUsing the buttons ▲/▼ switches the rotation speed of the cooling fans. The HIGH is the mode for use at highlands etc. Note that the projector is noisier when the HIGH is selected.
HIGH  NORMAL...

38

Maintenance
Maintenance
Lamp
 WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE
►The  projector  uses  a  high-pressure  mercury  glass  lamp.  The  lamp  can break 
with  a  loud  bang,  or  burn  out,  if  jolted  or  scratched,  handled  while  hot,  or  worn 
over  time.  Note  that  each  lamp  has  a  different  lifetime,  and  some  may  burst  or 
burn  out  soon  after  you  start  using  them.  In  addition,  when  the  bulb  bursts,  it  is 
possible  for  shards  of  glass  to  fly...

39

Lamp (continued)
When the indicators or a message prompt you to replace the lamp, replace the 
lamp as soon as possible.
1. Turn the projector off, and unplug the power cord. Allow the lamp to cool for 
at least 45 minutes.
2. To prepare a new lamp, contact your dealer and tell the lamp type number = 
78-6969-9797-8.  If the projector is mounted on the ceiling, or if the lamp has 
broken, also ask the dealer to replace the lamp.
In the case of replacement by yourself,
3. After making sure that the...

40

Maintenance
When  the  indicators  or  a  message  prompts  you  to  clean  the  air  filter,  clean  the  air  filter 
as  soon  as  possible.  Please  check  and  clean  the  air  filter  periodically,  even  if  there  is  no 
message.  If  the  air  filter  becomes  clogged  by  dust  or  the  like,  internal  temperatures  rise 
and the power may be automatically turned off for malfunction prevention.
1. Turn the projector off, and unplug the power cord. 
Allow the projector to cool for at least...