3M Multimedia Projector X40 Technical Manual
Have a look at the manual 3M Multimedia Projector X40 Technical Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 307 3M manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
S40/X40 Multimedia Projector Operators GuideTECHNICAL
1 TECHNICAL TECHNICAL SIGNAL CONNECTOR PIN ASSIGNMENT rgb D-sub 15-pin Shrink Mini Din 4-pins-video Mini Din 4-pin Pin NoSignal 1 Color: 0.286Vp-p (NTSC, burst signal), 75Ωterminator 0.3Vp-p (PAL/SECAM, burst signal), 75Ωterminator 2Brightness: 1.0Vp-p, 75Ωterminator 3Ground 4Ground Pin NoSignalPin NoSignal 1Video input Red9- 2Video input Green10Ground 3Video input Blue11- 4-12SDA (DDC) 5Ground13H. sync./ Composite sync. 6Ground Red14Vertical sync 7Ground Green15SCL (DDC) 8Ground Blue signalTerminalSpecification RGB signal inputrgb Video: Analog 0.7Vp-p, 75Ωterminator (positive) H/V. sync.: TTL level (positive/negative) Composite sync.: TTL level D-sub 15-pin shrink jack AUDIO input (from the computer)audio200mVrms, 50 kΩ(max. 3.0Vp-p) Stereo mini jack Video signal input video1.0Vp-p, 75Ωterminator, RCA jack s-video Brightness signal: 1.0Vp-p, 75Ωterminator Color signal: 0.286Vp-p (NTSC, burst signal),75Ωterminator 0.300Vp-p (PAL/SECAM, burst signal),75Ωterminator Mini DIN 4-pin jack component videoY1.0 Vp-p, 75 ΩTerminator (Positive) CB/PB0.7 Vp-p, 75 ΩTerminator (Positive) CR/PR0.7 Vp-p, 75 ΩTerminator (Positive) Audio input (from video equipment)audio¢RzL£200mVrms, 50 kΩ(max. 3.0Vp-p) RCA jack 495&$) 1.
2 Resolution H × ×VfH (kHz)fV (Hz)RatingSignal modeDisplay mode S40X40 720 ×40037.985.0VESATEXTZoom inZoom in 640 ×48031.559.9VESAVGA (60Hz)Zoom inZoom in 640 ×48035.066.7Mac13modeZoom inZoom in 640 ×48037.972.8VESAVGA (72Hz)Zoom inZoom in 640 ×48037.575.0VESAVGA (75Hz)Zoom inZoom in 640 ×48043.385.0VESAVGA (85Hz)Zoom inZoom in 800 ×60035.256.3VESASVGA (56Hz)Zoom in 800 ×60037.960.3VESASVGA (60Hz)Zoom in 800 ×60048.172.2VESASVGA (72Hz)Zoom in 800 ×60046.975.0VESASVGA (75Hz)Zoom in 800 ×60053.785.1VESASVGA (85Hz)Zoom in 832 ×62449.774.5Mac16modeZoom outZoom in 1024 ×76848.460.0VESAXGA (60Hz)Zoom out 1024 ×76856.570.1VESAXGA (70Hz)Zoom out 1024 ×76860.075.0VESAXGA (75Hz)Zoom out 1024 ×76868.785.0VESAXGA (85Hz)Zoom out 1152 ×86467.575.0VESASXGA (75Hz)Zoom outZoom out 1280 ×96060.060.0VESASXGA (60Hz)Zoom outZoom out 1280 ×102464.060.0VESASXGA (60Hz)Zoom outZoom out 1280 ×102480.075.0VESASXGA (75Hz)Zoom outZoom out 1280 ×102491.285.0VESASXGA (85Hz)Zoom outZoom out 1600 ×120075.060.0VESAUXGA (60Hz)Zoom outZoom out EXAMPLE OF COMPUTER SIGNAL •Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. • Be sure to check jack type, signal level, timing and resolution bef\ ore connecting this projector to a computer. • Depending on the input signal, full-size display may not be possibl\ e in some cases. Refer to the number of display pixels above. • This projector will display up to UXGA (1600X1200) resolution sig\ nals but the image will be rescaled to the native resolution of the projector. Best display\ performance is achieved when the signal input resolution is the same as the native reso\ lution of the projector. • The image may not be displayed correctly when the input sync. signa\ l is “Composite Sync.” or “Sync. on G”.NOTE 495&\ $) 1. Ö”´
3 The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.POSIT and H.POSIT of the menu. DATA HSYNCDATA VSYNCDisplay interval c Back porch b Sync aFront porch d Display interval c Back porch b Sync aFront porch d Computer / SignalHorizontal signal timing (µs) abcd TEXT2.03.020.31.0 VGA (60Hz)3.81.925.40.6 Mac 13mode2.13.221.22.1 VGA (72Hz)1.33.820.31.0 VGA (75Hz)2.03.820.30.5 VGA (85Hz)1.62.217.81.6 SVGA (56Hz)2.03.622.20.7 SVGA (60Hz)3.22.220.01.0 SVGA (72Hz)2.41.316.01.1 SVGA (75Hz)1.63.216.20.3 SVGA (85Hz)1.12.714.20.6 Mac 16mode1.13.914.50.6 XGA (60Hz)2.12.515.80.4 XGA (70Hz)1.81.913.70.3 XGA (75Hz)1.22.213.00.2 XGA (85Hz)1.02.210.80.5 1152×864 (75Hz)1.22.410.70.6 1280×960 (60Hz)1.02.911.90.9 1280×1024 (60Hz)1.02.311.90.4 1280×1024 (75Hz)1.11.89.50.2 1280×1024 (85Hz)1.01.48.10.4 1600×1200 (60Hz)1.21.99.90.4 Computer / SignalVertical signal timimg (lines) abcd TEXT3424001 VGA (60Hz)23348010 Mac 13mode3394803 VGA (72Hz)3284809 VGA (75Hz)3164801 VGA (85Hz)3254801 SVGA (56Hz)2226001 SVGA (60Hz)4236001 SVGA (72Hz)62360037 SVGA (75Hz)3216001 SVGA (85Hz)3276001 Mac 16mode3396241 XGA (60Hz)6297683 XGA (70Hz)6297683 XGA (75Hz)3287681 XGA (85Hz)3367681 1152×864 (75Hz)3328641 1280×960 (60Hz)3369601 1280×1024 (60Hz)33810241 1280×1024 (75Hz)33710242 1280×1024 (85Hz)34410241 1600×1200 (60Hz)34612001 INITIAL SET SIGNALS 495&$) 1.
4 (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and after the computer has started up, turn on the projector power supply. control jack D-sub 15-pin shrink jack123456789101112131415 RD TD GND SELO RTS 123456789 CD RD TD DTR GND DSR RTS DTS RI 12345 67 89 RS-232C jack D-sub 9-pin Projector Computer Communications setting 19200bps, 8N1 1 Protocol Consist of header (7 bytes) + command data (6 bytes). 2 Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data. CRC_high : Upper byte of CRC flag for command data. 3 Command data byte_0byte_1byte_2byte_3byte_4byte_5 ActionTypeSetting code lowhighlowhighlowhigh Command data chart Action (byte_0 - 1) ActionClassificationContent 1SETChange setting to desired value. 2GETRead projector internal setup value. 4INCREMENTIncrement setup value by 1. 5DECREMENTDecrement setup value by 1. 6EXECUTERun a command. RS-232C COMMUNICATION 495&$) 1.
5 Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code ‘06H’ to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector changes the specified setting to the default value. (3) The projector returns the response code ‘06H’ to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes) +‘00H’ + ‘00H’) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code ‘06H’ to the computer. When the projector cannot understand the received command When the projector cannot understand the received command, the error code ‘15H’ is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code ‘15H’ is sent back to the computer. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code ‘1cH’ + ‘xxxxH’ is sent back to the computer. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the computer. •Operation cannot be guaranteed when the projector receives an undefined command or data. • Provide an interval of at least 40ms between the response code and any other code. • The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. • Commands are not accepted during warm-up. NOTE 495&$) 1.
6 Command data chart NamesOperation typeHeaderCommand data CRCActionTypeSetting code Blank ColorSet BlueBE EF0306 00CB D301 0000 3003 00 WhiteBE EF0306 006B D001 0000 3005 00 BlackBE EF0306 009B D001 0000 3006 00 GetBE EF0306 0008 D302 0000 3000 00 MirrorSet NormalBE EF0306 00C7 D201 0001 3000 00 H InverseBE EF0306 0057 D301 0001 3001 00 V lnverseBE EF0306 00A7 D301 0001 3002 00 H&V InverseBE EF0306 0037 D201 0001 3003 00 GetBE EF0306 00F4 D202 0001 3000 00 FreezeSetNormalBE EF0306 0083 D201 0002 3000 00 FreezeBE EF0306 0013 D301 0002 3001 00 GetBE EF0306 00B0 D202 0002 3000 00 StartupSetTURN ONBE EF0306 000B D201 0004 3000 00 TURN OFFBE EF0306 009B D301 0004 3001 00 GetBE EF0306 0038 D202 0004 3000 00 LanguageSet EnglishBE EF0306 00F7 D301 0005 3000 00 FrançaisBE EF0306 0067 D201 0005 3001 00 DeutschBE EF0306 0097 D201 0005 3002 00 EspañolBE EF0306 0007 D301 0005 3003 00 ItalianoBE EF0306 0037 D101 0005 3004 00 NorskBE EF0306 00A7 D001 0005 3005 00 NederlandsBE EF0306 0057 D001 0005 3006 00 PortuguêsBE EF0306 00C7 D101 0005 3007 00 ÔŠ BE EF0306 0037 D401 0005 3008 00 ¤BE EF0306 00A7 D501 0005 3009 00 BE EF0306 0057 D501 0005 300A 00 GetBE EF0306 00C4 D302 0005 3000 00 Magnify GetBE EF0306 007C D202 0007 3000 00 IncrementBE EF0306 001A D204 0007 3000 00 DecrementBE EF0306 00CB D305 0007 3000 00 Auto off GetBE EF0306 0008 8602 0010 3100 00 IncrementBE EF0306 006E 8604 0010 3100 00 DecrementBE EF0306 00BF 8705 0010 3100 00 Brightness ResetExecuteBE EF0306 0058 D306 0000 7000 00 Contrast ResetExecuteBE EF0306 00A4 D206 0001 7000 00 V.Position ResetExecuteBE EF0306 00E0 D206 0002 7000 00 RS-232C COMMUNICATION (continued)
7
NamesOperation typeHeaderCommand data
CRCActionTypeSetting code
H.Position ResetExecuteBE EF0306 00IC D306 0003 7000 00
H.Size ResetExecuteBE EF0306 0068 D206 0004 7000 00
Color Balance R ResetExecuteBE EF0306 0094 D306 0005 7000 00
Color Balance B ResetExecuteBE EF0306 00D0 D306 0006 7000 00
Sharpness ResetExecuteBE EF0306 00C4 D006 0009 7000 00
Color ResetExecuteBE EF0306 0080 D006 000A 7000 00
Tint ResetExecuteBE EF0306 007C D106 000B 7000 00
Keystone_V ResetExecuteBE EF0306 0008 D006 000C 7000 00
Auto AdjustExecuteBE EF0306 0091 D006 000A 2000 00
Lamp Time ResetExecuteBE EF0306 0058 DC06 0030 7000 00
Filter Time ResetExecuteBE EF0306 0098 C606 0040 7000 00
Blank on/offSetoffBE EF0306 00FB D801 0020 3000 00
onBE EF0306 006B D901 0020 3001 00
GetBE EF0306 00C8 D802 0020 3000 00
Error StatusGet
BE EF0306 00D9 D802 0020 6000 00
(Example of Return)
00 00 01 00 02 00 03 00
(Normal) (Cover-error) (Fan-error) (Lamp-error)
04 00 05 00 06 00 07 00 \
08 00
(Temp-error) (Air flow-error) (Lamp-Time-over) (Cool-er\
ror) (Filter-Error)
PowerSetOFFBE EF0306 002A D301 0000 6000 00ONBE EF0306 00BA D201 0000 6001 00
GetBE EF0306 0019 D302 0000 6000 00
Input SourceSet
RGBBE EF0306 00FE D201 0000 2000 00
VideoBE EF0306 006E D301 0000 2001 00
SVideoBE EF0306 009E D301 0000 2002 00
ComponentBE EF0306 00AE D101 0000 2005 00
GetBE EF0306 00CD D202 0000 2000 00
Volume
GetBE EF0306 0031 D302 0001 2000 00
IncrementBE EF0306 0057 D304 0001 2000 00
DecrementBE EF0306 0086 D205 0001 2000 00
MuteSetNormalBE EF0306 0046 D301 0002 2000 00
MuteBE EF0306 00D6 D201 0002 2001 00
GetBE EF0306 0075 D302 0002 2000 00
Brightness
GetBE EF0306 0089 D202 0003 2000 00
IncrementBE EF0306 00EF D204 0003 2000 00
DecrementBE EF0306 003E D305 0003 2000 00
8 Command data chart (continued) NamesOperation typeHeaderCommand data CRCActionTypeSetting code Contrast GetBE EF0306 00FD D302 0004 2000 00 IncrementBE EF0306 009B D304 0004 2000 00 DecrementBE EF0306 004A D205 0004 2000 00 Color Balance R GetBE EF0306 0001 D202 0005 2000 00 IncrementBE EF0306 0067 D204 0005 2000 00 DecrementBE EF0306 00B6 D305 0005 2000 00 Color Balance B GetBE EF0306 0045 D202 0006 2000 00 IncrementBE EF0306 0023 D204 0006 2000 00 DecrementBE EF0306 00F2 D305 0006 2000 00 Keystone_V GetBE EF0306 00B9 D302 0007 2000 00 IncrementBE EF0306 00DF D304 0007 2000 00 DecrementBE EF0306 000E D205 0007 2000 00 AspectSet 4:3BE EF0306 009E D001 0008 2000 00 16:9BE EF0306 000E D101 0008 2001 00 SmallBE EF0306 00FE D101 0008 2002 00 GetBE EF0306 00AD D002 0008 2000 00 Picture Position at 16 : 9 or SmallSet DefaultBE EF0306 0062 D101 0009 2000 00 BottomBE EF0306 00F2 D001 0009 2001 00 TopBE EF0306 0002 D001 0009 2002 00 GetBE EF0306 0051 D102 0009 2000 00 V.Position GetBE EF0306 000D 8302 0000 2100 00 IncrementBE EF0306 006B 8304 0000 2100 00 DecrementBE EF0306 00BA 8205 0000 2100 00 H.Position GetBE EF0306 00F1 8202 0001 2100 00 IncrementBE EF0306 0097 8204 0001 2100 00 DecrementBE EF0306 0046 8305 0001 2100 00 H.Size GetBE EF0306 00B5 8202 0002 2100 00 IncrementBE EF0306 00D3 8204 0002 2100 00 DecrementBE EF0306 0002 8305 0002 2100 00 H.Phase GetBE EF0306 0049 8302 0003 2100 00 IncrementBE EF0306 002F 8304 0003 2100 00 DecrementBE EF0306 00FE 8205 0003 2100 00 Sharpness GetBE EF0306 00F1 7202 0001 2200 00 IncrementBE EF0306 0097 7204 0001 2200 00 DecrementBE EF0306 0046 7305 0001 2200 00 Color GetBE EF0306 00B5 7202 0002 2200 00 IncrementBE EF0306 00D3 7204 0002 2200 00 DecrementBE EF0306 0002 7305 0002 2200 00
9 NamesOperation typeHeaderCommand data CRCActionTypeSetting code Tint GetBE EF0306 0049 7302 0003 2200 00 IncrementBE EF0306 002F 7304 0003 2200 00 DecrementBE EF0306 00FE 7205 0003 2200 00 Video FormatSet AutoBE EF0306 009E 7501 0000 220A 00 NTSCBE EF0306 00FE 7101 0000 2204 00 PALBE EF0306 006E 7001 0000 2205 00 SECAMBE EF0306 006E 7501 0000 2209 00 NTSC 4.43BE EF0306 005E 7201 0000 2202 00 M-PALBE EF0306 00FE 7401 0000 2208 00 N-PALBE EF0306 000E 7101 0000 2207 00 GetBE EF0306 000D 7302 0000 2200 00 HDTVSet1080iBE EF0306 00F2 7301 0005 2200 00 1035iBE EF0306 0062 7201 0005 2201 00 GetBE EF0306 00C1 7302 0005 2200 00 Sync on GSetoffBE EF0306 00CB D001 0008 3001 00 onBE EF0306 005B D101 0008 3000 00 GetBE EF0306 0068 D102 0008 3000 00 WHISPERSetNORMALBE EF0306 003B 2301 0000 3300 00 WHISPERBE EF0306 00AB 2201 0000 3301 00 GetBE EF0306 0008 2302 0000 3300 00 GAMMASet NORMALBE EF0306 00C7 F001 00A1 3000 00 CINEMABE EF0306 0057 F101 00A1 3001 00 DYNAMICBE EF0306 00A7 F101 00A1 3002 00 GetBE EF0306 00F4 F002 00A1 3000 00 Lamp TimeGetBE EF0306 00C2 FF02 0090 1000 00 Filter TimeGetBE EF0306 00C2 F002 00A0 1000 00