3M Multimedia Projector Mp8749 Operators Manual
Have a look at the manual 3M Multimedia Projector Mp8749 Operators Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 307 3M manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 7
6
Angle Adjustment
1Lift up the front side of the
projector, and pressing the foot
adjuster button, adjust the
projection angle.
2Release the button to lock at the desired angle.
3Turn the rear foot adjuster to adjust
the left-right slope. Do not force the
foot adjuster screws. This could
damage the adjusters or cause the
lock to fail.
Use the foot adjusters on the bottom of the projector to adjust the proj\
ection
angle. It is variable within 0˚ to 9 ˚ approximately.
CAUTION• Install the projector in a...](http://img.usermanuals.tech/thumb/96/87286/w64_3m-mp8749-manual_d-6.png "Page 7
6
Angle Adjustment
1Lift up the front side of the
projector, and pressing the foot
adjuster button, adjust the
projection angle.
2Release the button to lock at the desired angle.
3Turn the rear foot adjuster to adjust
the left-right slope. Do not force the
foot adjuster screws. This could
damage the adjusters or cause the
lock to fail.
Use the foot adjusters on the bottom of the projector to adjust the proj\
ection
angle. It is variable within 0˚ to 9 ˚ approximately.
CAUTION• Install the projector in a...")
![Page 8
7
Refer to the illustrations and tables below to determine the screen size\
and
projection distance.
Adjusting the Screen Size and Projection Distance
If 4:3 aspect ratio
4
3
The values shown in the table are calculated for a full size screen
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)
Top View
Side View
a
Screen size [inches (m)]a[inches (m)]
Min.Max.
40 (1.0)47...](http://img.usermanuals.tech/thumb/96/87286/w64_3m-mp8749-manual_d-7.png "Page 8
7
Refer to the illustrations and tables below to determine the screen size\
and
projection distance.
Adjusting the Screen Size and Projection Distance
If 4:3 aspect ratio
4
3
The values shown in the table are calculated for a full size screen
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)
Top View
Side View
a
Screen size [inches (m)]a[inches (m)]
Min.Max.
40 (1.0)47...")
![Page 9
8
Display monitors
DVD players
VCRs
Laptop computers
Desktop computers
Indicates the
corresponding
reference page
ATTENTIONPrecautions to observe when connecting other devices to the projector :
• Whenever attempting to connect other devices to the projector, please th\
oroughlyread the manual of each device to be connected.
• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempti\
ng to connect a live device to the projector may generate extremely loud noise\
s or other...](http://img.usermanuals.tech/thumb/96/87286/w64_3m-mp8749-manual_d-8.png "Page 9
8
Display monitors
DVD players
VCRs
Laptop computers
Desktop computers
Indicates the
corresponding
reference page
ATTENTIONPrecautions to observe when connecting other devices to the projector :
• Whenever attempting to connect other devices to the projector, please th\
oroughlyread the manual of each device to be connected.
• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempti\
ng to connect a live device to the projector may generate extremely loud noise\
s or other...")
![Page 10
9
Ports and Cables
Refer to the table below to find out which projector port and cable to u\
se for connecting a
given device. Use this table for determining which cables to prepare.
About Plug-and-Play Capability
• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be a\
chieved by
connecting this projector to computers that are VESA DDC (display data \
channel)
compatible. Please take advantage of this function by connecting the acc\
essory RGB
cable to the RGB IN 1 port (DDC 1/2B...](http://img.usermanuals.tech/thumb/96/87286/w64_3m-mp8749-manual_d-9.png "Page 10
9
Ports and Cables
Refer to the table below to find out which projector port and cable to u\
se for connecting a
given device. Use this table for determining which cables to prepare.
About Plug-and-Play Capability
• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be a\
chieved by
connecting this projector to computers that are VESA DDC (display data \
channel)
compatible. Please take advantage of this function by connecting the acc\
essory RGB
cable to the RGB IN 1 port (DDC 1/2B...")
![Page 15
14
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control)
• The projector begins warming up and the POWER
indicator blinks green.
• The POWER indicator stops blinking and
lights to solid green once the projectors
power is completely on.
4Open the...](http://img.usermanuals.tech/thumb/96/87286/w64_3m-mp8749-manual_d-14.png "Page 15
14
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control)
• The projector begins warming up and the POWER
indicator blinks green.
• The POWER indicator stops blinking and
lights to solid green once the projectors
power is completely on.
4Open the...")
10 #AUDIO INAUDIO cable RGB cable AUDIO OUT RGB IN Analogue RGB OUT AUDIO IN VIDEO IN S-VIDEO IN AUDIO IN AUDIO OUT 1 12 2 USBRGB IN RGB OUTCONTROL # Laptop computer #%$USB IN USB OUT AUDIO IN AUDIO OUT RGB IN Analogue RGB OUT CONTROL IN CONTROL OUT If connecting to a USB port equipped computerRGB cable AUDIO cable USB cableMOUSE cable AUDIO IN VIDEO IN S-VIDEO IN AUDIO IN AUDIO OUT 1 12 2USBRGB IN RGB OUTCONTROL #%$ Desktop computer CONNECTING YOUR DEVICES (continued) Connecting to a Computer ATTENTIONWhenever attempting to connect a laptop computer to the projector, be sure to activate the laptops RGB external image output (set the lap\ top to CRT display or to simultaneous LCD and CRT display). For details on how thi\ s is done, please refer to the instruction manual of the corresponding laptop compu\ ter. • Some computers may have multiple display screen modes. Use of some of t\ hese modes will not be possible with this projector. • For some RGB input modes, the optional Mac adapter is necessary. NOTE $1948&/7 4 .
11 #$ *GVTJOHBDPNQPOFOU WJEFPDPOOFDUJPO*GVTJOHBOBVEJPWJEFP DPOOFDUJPO COMPONENT VIDEO IN COMPONENT VIDEO OUTAUDIO/VIDEO INAUDIO/VIDEO OUT S-VIDEO IN S-VIDEO OUT If using a S-video connection COMPONENT cable AUDIO/VIDEO cable S-VIDEO cable AUDIO IN VIDEO IN S-VIDEO IN AUDIO IN AUDIO OUT 1 12 2USBRGB IN RGB OUTCONTROL ###$ DVD player # If using a S-video connection 6%*07*%&0*/ 6%*07*%&0065 47*%&0*/ 47*%&0065 AUDIO/VIDEO cable S-VIDEO cable AUDIO IN VIDEO IN S-VIDEO IN AUDIO IN AUDIO OUT 1 12 2 USBRGB IN RGB OUTCONTROL # VCR Connecting to a DVD Player Connecting to a VCR $1948&/7 4 .
12 RGB cable 3(#065 3(#*/ AUDIO IN VIDEO IN S-VIDEO IN AUDIO INAUDIO OUT 112 2USBRGB IN RGB OUTCONTROL CONNECTING YOUR DEVICES (continued) Connecting to a Display Monitor Display monitor $1948&/7 4 .
1Remove the battery cover Push the knob while lifting up the battery cover in the direction of the arrow. Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicatedin the remote control). Close the battery cover Replace the battery cover in the direction of the arrow and snap it back into place. • The remote control works with both the projectors front and rear remote sensors. • The range of the remote sensor on the front and back is 3 meters with a 60-degree range (30 degrees to the left and right of the remote sensor). • Since the remote control uses infrared light to send signals to the projector (Class 1 LED), be sure to use the remote control in an area free from obstacles that could block the remote controls output signal to the projector. approximately 3 meters approximately 3 meters 30 degrees30 degrees30 degree s30 degrees 23 USING THE REMOTE CONTROL Putting batteries into the remote control unit Operating the remote control • Only use the accompanying remote control. Using other remote controls (\ even of similiar models) to control the CP-X385W may result in unexpected operation. $1948&/7 4 .
14 1Make sure that the power cord is firmly and correctly connected to the projector and outlet 2Turn on the projectors power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange. 3Press the STANDBY/ON button (control panel or remote control) • The projector begins warming up and the POWER indicator blinks green. • The POWER indicator stops blinking and lights to solid green once the projectors power is completely on. 4Open the slide lens door The picture is projected. POWER-indikator STANDBY/ON STANDBY/ONLASERBLANK RGBVIDEO TURNING ON THE POWER Control panel Precautions Connect all devices to be used to the projector prior to turning on the power.™ WARNINGWhen the power is ON, a strong light is emitted. Do not look into the lens. Turn the power on/off in right order. • Power on the projector before the computer or video tape recorder. • Power off the projector after the computer or video tape recorder. NOTE på/av-bryter $1948&/7 4 .
RGB 15 6Use the zoom ring to adjust the screen size 7Use the focus ring to focus the picture 5 If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2. Select the signal you wish to project. If selecting video input Press the VIDEO button Press this button to toggle between the devices connected to VIDEO IN, S- VIDEO IN and COMPONENT VIDEO. As illustrated below, each time you press the VIDEO button, the projector switches between VIDEO IN, S-VIDEO IN and COMPONENT VIDEO. Select the signal you wish to project. Using the remote control Press the INPUT button As illustrated below, each time you press the INPUT button, the projector switches between its input signal ports. Select the signal you wish to project. Using the projectors control panel VIDEO RGB IN 1 RGB IN 2 VIDEO INS-VIDEO IN COMPONENT VIDEO VIDEO IN S-VIDEO IN COMPONENT VIDEO RGB IN 1 RGB IN 2 INPUT Selecting an Input Signal $1948&/7 4 .
16 STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME MUTE 1Press the STANDBY/ON button (control panel or remote control) The message Power off? will appear on the screen for approximately 5 seconds. 3Check that the POWER indicator stops blinking and lights to solid orange. Switch the power switch to [O] (OFF). 4Confirm that the POWER indicator has gone off and then close the slide lens door. When the projector has completed powering down, the POWER indicator will go off. STANDBY/ON TURNING OFF THE POWER Control panel 2Press the STANDBY/ON button again (control panel or remote control) Press the STANDBY/ON button again while the Power off? message is visible. The projector lamp goes off and starts cooling down. The POWER indicator blinks orange while the lamp cools down. (Pressing the STANDBY/ON button while the POWER indicator is blinking orange has no effect.) The system goes into the STANDBY mode after cooling down and the POWER indicator stops blinking orange and then lights to solid orange. STANDBY/ON • Except in emergencies, follow the above- mentioned procedure for turning power off. NOTE POWER-indikator på/av-bryter $1948&/7 4 .
17 STANDBY/ONLASERBLANK RGBVIDEO AUTO MENUENTERKEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE 1Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume. 1Press the MUTE button As illustrated on the right, a dialog will appear on the screen indicating that you have muted the sound. Press the VOLUME button to close the dialog. (Even if you dont do anything, the dialog will automatically disappear after a few seconds.) Press the MUTE button again to restore the sound. 2Press the , buttons to adjust the volume Press the VOLUME button again to close the dialog and complete this operation. (Even if you dont do anything, the dialog will automatically disappear after a few seconds.) Press this to increase the volume Press this to decrease the volume VOLUME MUTE AUTO MENU ENTERKEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE 16 VOLUME 16 VOLUME 16 VOLUME ADJUSTING THE VOLUME TEMPORARILY MUTING THE SOUND $1948&/7 4 .
18 STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTERKEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE 1Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position. 2Use the , , , buttons to adjust the position When you want to initialize the position, press the RESET button during adjustment. Press the POSITION button again to close the dialog and complete this operation. (Even if you dont do anything, the dialog will automatically disappear after a few seconds.) This function is only available for RGB IN 1/2 input. ADJUSTING THE POSITION POSITION POSITION Control panel $1948&/7 4 .
19 The automatic adjustment operation requires approximately 10 seconds. Al\ so, pleasenote that it may not function correctly with some input signals. NOTE 1 USING THE AUTOMATIC ADJUSTMENT FEATURE Press the AUTO button Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE) and horizontal size (H. SIZE) are automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. Dark pictures may still be incorrectly adjusted. Use a bright screen when adjusting. The signal type best suited for the respective input signal is selected automatically. This feature is available only if VIDEO is set to AUTO in the INPUT menu. Automatic Adjustment for RGB Input Automatic Adjustment for Video Input STANDBY/ONLASERBLANK RGBVIDEO AUTO MENU ENTER KEYSTONE RESET FREEZE ASPECT ESC MAGNIFY POSITION OFF ONVOLUME SEARCH MUTE AUTO $1948&/7 4 .