3M Multimedia Projector Mp8740 Quickstart Setup Manual

							3M MP8730/MP8740 Multimedia Projec tor Qui ck Se tup Inst ructions
© 3M  1999 78-6970-8033-7
AUDIO
2
AUDIO
K
1
AUDIO2AUDIO
K
8730-23A
MP8740 
						

							3M MP8730/MP8740 Multimedia Projector Quick Setup Instructions
Project Packout
Remote Control TransmitterProjector Startup
FOCUSZOOM
CLOSE
OPEN
1. Make all cable connections and line hookups with the power off.
2.Turn the POWER SWITCH       of the projector on. The ON indicator will light up orange.
3.Move the LENS SHUTTER CONTROL         to the open position.
4.Press the STANDBY/ON button        .  The ON indicator blinks (green) and then lights (green).
The ON indicator will blink green during warm-up and lamp ignition.
5.Adjust the screen size using the ZOOM button            .
6.Adjust the focus using the FOCUS button            .
7.Turn on all connected equipment. The method of connecting various equipment, see section 2.3.
8.Press the INPUT button         on the projector or the INPUT SELECT (VIDEO or RGB) button
on the remote to select the source of the signal to be projected on the screen. The selected signal
input is displayed at the bottom right of the screen.  The display will show the last selected input source
before power was turned off.
ZOOM
FOCUS
CLOSE
OPEN
Projector Startup Procedure
Projector Shutdown Procedure
1. Hold the STANDBY/ON button        for 3-5 seconds. The ON indicator blinks orange and the lamp
turns off. After approximately 1 minute, the fan stops and the indicator stays orange.
2.Turn the MAIN POWER SWITCH      of the projector off.
3. Close the LENS SHUTTER    .   Push up on the lens cover switch to close.
4. Disconnect cables.
Caution
Do not turn off the POWER SWITCH before pressing the STANDBY/ON button.  After the STANDBY/ON
button is pressed, the fan rotates for about 1 minute to cool the projector.
CLOSE
OPEN
INPUT RGB1/2 VIDEO1/2BLANK TIMER MENU ON MOUSE ONRIGHTLASER VOLUMEMUTE STANDBY/ON
ZOOM FOCUS
POSITION ON
RESET
STANDBY / ON buttonSet main power switch to ON.
Press and hold STANDBY/ON button for
projector mode (lamp on) or standby
mode (lamp off).
FOCUS buttonPress +/- to adjust image sharpness.
ZOOM buttonPress +/- to adjust image size.
Note: If needed, move projector
closer/further from screen.
POSITION buttonPress and light POSITION button.
Move DISK PAD to adjust horizontal/
vertical image position.
DISK PADSelect mode, then move DISK PAD to
position image, navigate menus or control
mouse functions. To select the mode:
   • Press and light POSITION button for
     position mode.
   • Press and light MENU ON button for
     menu mode.
MENU ON buttonPress and light MENU ON button to
display the Main Menu. Move DISK PAD
to select menu and/or adjust screen
values.
BLANK ON buttonPress BLANK to display a blank
background with no image. Press again to
return the image to the screen.
INPUT buttonsRGB 1/2: Select computer video input
(RGB1 Ô RGB2 Ô RGB1).
VIDEO 1/2: Select video inputs
(VIDEO1 Ô VIDEO2 Ô VIDEO1).
MUTE buttonPress MUTE to switch the audio
sound ON or OFF
VOLUME buttonPress +/- to adjust internal/external speaker
volume.
LASER POINTERPress and hold down button to project laser
pointer.
                     CAUTIONTo prevent injury to eyesight, do not point
laser beam at other persons or look directly
into laser beam.
RESET / RIGHT MOUSE buttonRESET: When a menu is being displayed,
press RESET to return menu value to factory
setting.
RIGHT MOUSE: When computer image is
being displayed, press for right mouse button
function.
MOUSE ON buttonPress MOUSE ON button to activate mouse
mode. Move DISK PAD to control mouse
functions.
TIMER ON / OFF buttonPress TIMER to display and start the timer as
set in OPT menu setting. Note: Timer will not
display on a blank screen. To remove TIMER
display press again.
Backside
of Remote
LEFT MOUSE
button
Packout Items not Shown:
¥ PS/2 mouse cable .............. (1)
¥ ADB mouse cable ............. (1)
¥ Serial mouse cable ............ (1)
¥ Stereo mini-jack ................ (1)
Multimedia Projector Remote Control Transmitter
(batteries included)
VGA Cable
(15-15 pin M/M) 3-Conductor
Video/Audio CableAdapter
with dip switchVideo Cable
(S-Video mini
DIN4-pin) Power Cord
110V Ð US
220V Ð UK, Europe