3M Multimedia Projector Mp8725 Quickstart Setup Manual

							3
MP8725/MP8635 Multimedia Projector Quick Setup Instructions
Cable Connections:  Always turn power off when making any cable connections.
Technical Assistance & Product Information
1-800-328-1371
E-mail: [email protected]
© 3M 1999 78-6970-8992-4
VIDEO S-VIDEO IN
(L)MONO(R) AUDIO IN
12AUDIO
OUT AUDIO IN
12RGB IN
CONTROL RGB OUT
MONITOR
PORT
CRT 
Display
PC
MAC
or PC
LaptopMAC
OUT
MONITOR
PORT
PS/2 or
SERIAL 
PORT
VCRAudio L/R
VideoIN OUT OUT OUTRED WHT YEL
IN
IN
Laser Disc
OUT OUTRED WHT
OUT
IN
IN
IN
S-VHS
Audio LeftAudio Right
RGB IN
RGB IN
CONTROLRGB OUT
OI
12AUDIO
OUT AUDIO IN
AC IN
12RGB IN
VIDEO S-VIDEO IN
(L)MONO(R) AUDIO IN
CONTROL RGB OUT
Power 
						

							3
MP8725/MP8635 Multimedia Projector Quick Setup Instructions
Packout Items Show Above:
¥ PS/2 mouse cable ......................................... (1)
¥ ADB mouse cable ........................................ (1)
¥ Serial mouse cable ....................................... (1)
¥ Stereo mini-jack ........................................... (1)
Project PackoutProjector StartupRemote Control Transmitter
EPS-04A
Power Cord
110V - US
220 - UK, Europe3-Conductor
Video/Audio Cable Multimedia Projector Remote Control Transmitter
(batteries included)
VGA Cable
(15-15 pin M/M)Adapter
with dip switchVideo Cable
(S-Video mini DIN4-pin)
INPUT RGB1/2 VIDEO1/2BLANK TIMER MENU ON MOUSE ONRIGHTLASER VOLUME
OFFMUTE STANDBY/ON
MAGNIFYPOSITION ON
RESET
AC IN
12AUDIO
OUT AUDIO IN12
RGB IN
CONTROLRGB OUT
VIDEO S-VIDEO IN
(L)MONO(R) AUDIO IN
STANDBY/ON
INPUT
MUTE
MENU
RESET
LAMP
TEMP
AC IN
12AUDIO
OUT AUDIO IN
12
RGB IN
CONTROLRGB OUT
VIDEO S-VIDEO IN
(L)MONO(R) AUDIO IN
STANDBY/ON
INPUT
MUTE
MENU
RESET
LAMP
TEMP
OI
EPS-07A
STANDBY/ON
INPUT
MUTE
MENU
RESET
LAMPTEMP
1. Make all cable connections and line hookups with the power off.
2. Turn the POWER SWITCH            of the projector on.
The ON indicator will light up orange.
3. Press the STANDBY/ON button       .  The ON indicator blinks (green) and
then lights (green). The ON indicator will blink green during warm-up and lamp
ignition. When power is turned off, there is a 60 second reset period before the
STANDBY/ON button will function again.
4. Adjust the screen size by rotating the ZOOM CONTROL.
5. Adjust the focus by rotating the projection lens.
6. Turn on all connected equipment.
See section 2.3 of the Operators Guide.
7. Press the INPUT button         on the projector or the INPUT SELECT
(VIDEO or RGB) button on the remote to select the source of the signal to
be projected on the screen. The selected signal input is displayed at the bottom
right of the screen.  The display will show the last selected input source before
power was turned off.1. Hold the STANDBY/ON button        for 3-5 seconds. The ON indicator blinks
orange and the lamp turns off. After approximately 1 minute, the fan stops and
the indicator stays orange.
2.Turn the MAIN POWER SWITCH            of the projector off.
3. Disconnect cables.
OI
OI
Do not turn off the POWER SWITCH before pressing the STANDBY/ON button. After the
STANDBY/ON button is pressed, the fan rotates for about 1 minute to cool the projector.
Caution
Projector Shutdown Procedure
STANDBY / ON buttonSet main power switch to ON. Press and
hold STANDBY/ON button for projector
mode (lamp on) or standby mode (lamp off).FREEZE button 
(For the MP8635 Only)
Press to display single frame of projector
image. Press again to release freeze
function. 
(Operation of Disk Pad and some
setup items will not function when freeze is
active.)
MAGNIFY buttonsPress +/- to magnify image (4x
magification). Press POSITION button and
use disc pad to view entire image. Press
OFF button to return to normal image size.POSITION buttonPress and light POSITION button.
Move DISC PAD to adjust horizontal/
vertical image position.DISC PADSelect mode, then move DISC PAD to
position image, navigate menus or control
mouse functions. To select the mode:
   • Press and light POSITION button for
     position mode.
   • Press and light MENU ON button for
     menu mode.MENU ON buttonPress and light MENU ON button to display
the Main Menu. Move DISC PAD to select
menu and/or adjust screen values.BLANK ON buttonPress BLANK to display a blank
background with no image. Press again to
return the image to the screen.INPUT buttonsRGB 1/2: Select computer video input
(RGB1 Ô RGB2 Ô RGB1).
VIDEO 1/2: Select video inputs
(VIDEO1 Ô VIDEO2 Ô VIDEO1).
MUTE buttonPress MUTE to switch the audio
sound ON or OFFVOLUME buttonPress +/- to adjust internal/external speaker
volume.LASER POINTERPress and hold down button to project laser
pointer.                     CAUTIONTo prevent injury to eyesight, do not point
laser beam at other persons or look directly
into laser beam.RESET / RIGHT MOUSE buttonRESET: When a menu is being displayed,
press RESET to return menu value to factory
setting.
RIGHT MOUSE: When computer image is
being displayed, press for right mouse button
function.MOUSE ON buttonPress MOUSE ON button to activate mouse
mode. Move DISK PAD to control mouse
functions.TIMER ON / OFF buttonPress TIMER to display and start the timer as
set in OPT menu setting. Note: Timer will not
display on a blank screen. To remove TIMER
display press again.Backside
of RemoteLEFT MOUSE
button
LASER APERTURE
INPUT RGB VIDEO BLANK TIMER MENU ON MOUSE ONRIGHTLASER VOLUME
OFF
FREEZEMUTE STANDBY/ON
MAGNIFY
POSITION ON
RESET