3M Multimedia Projector Mp7650 Operators Manual

11
ENGLISH
#$
*G
VTJOH
B
DPNQPOFOU

WJEFP
DPOOFDUJPO*G
VTJOH
BO
BVEJPWJEFP

DPOOFDUJPO
AUDIO IN
COMPONENT   VIIDEO R         L / (MONO)  VIDEO IN
C
R / RR                    CB / PB                          Y K
S-VIDEO IN
USB
1                  RGB   IN                    2
RGB   OUT                                  CONTROL

###$
COMPONENT VIDEO INCOMPONENT VIDEO  OUTAUDIO/VIDEO INAUDIO/VIDEO OUT S-VIDEO INS-VIDEO OUT
If using a S-video 
connection
COMPONENT cable AUDIO/VIDEO cable
S-VIDEO cable
DVD...

12
RGB cable

AUD IO IN
COMPONENT   VIIDEO R         L / (MONO)  VIDEO IN
C
R / RR                    CB / PB                          Y K
S-VIDEO IN
USB
1                  RGB   IN                    2
RGB   OUT                                  CONTROL

3(#
0653(#
*/
CONNECTING YOUR DEVICES (continued)
Connecting to a Display Monitor
Display monitor
$1487	4




1.



13
ENGLISH
1Remove the battery
cover
Slide back and remove
the battery cover in the
direction of the arrow.
Insert the batteries
Align and insert the two AA
batteries (that came with the
projector) according to their plus
and minus terminals (as indicatedin the remote control).
Close the battery
cover
Replace the battery cover
in the direction of the arrow
and snap it back into place.
• The remote control works with both the
projectors front and rear remote sensors.
• The range of the remote sensor on...

14
STANDBY/ONINPUTKEYSTONE
RESETLANP
TEN P
P O W ER
1Make sure that the power cord is firmly and
correctly connected to the projector and outlet
2Turn on the projectors power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
3Press the STANDBY/ON button (control
panel or remote control) 
• The projector begins warming up and the POWER
indicator blinks green.
•  The POWER indicator stops blinking
and lights to solid green once...

RGB
15
ENGLISH
6Use the zoom ring to adjust the
screen size
7Use the focus ring to focus the
picture
5
If selecting RGB input
Press the RGB button
Press this button to toggle between the
devices connected to RGB IN 1 and 2.
As illustrated below, each time you
press the RGB button, the projector
switches between RGB IN 1 and 2.
Select the signal you wish to project.
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, S-
VIDEO IN and...

16
VIDEO
ASPECT
HOME
END MUTE
PAGE DOWN
KEYSTONE
FREEZE OFFON
MENU
POSITION
ENTER
ESC RESET
PAGE UP VOLUME
MAGNIFY
AUTO BLANK
RGB SEARCH
STANDBY/ON
1Press the STANDBY/ON button (control
panel or remote control)
The message Power off? will appear on the screen for approximately 5 s\
econds. 
3Check that the POWER indicator stops
blinking and lights to solid
orange.
Switch the power switch to
[O] (OFF).
4Confirm that the POWER indicator has
gone off and then attach the lens cap.
When the projector has...

17
ENGLISH
VIDEO
ASPECT
HOME
END
MUTE PAGE DOWN
KEYSTONE FREEZEOFFON
MENU POSITION
ENTER
ESC RESET
PAGE UP VOLUME
MAGNIFY
AUTO BLANK RGB SEARCH
STANDBY/ON
1Press the VOLUME button
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
1Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound.  Press
the VOLUME button to close the dialog.  (Even if you dont
do anything, the dialog will...

18
VIDEO
ASPECT
HOME
END
MUTE PAGE DOWN
KEYSTONE FREEZEOFFON
MENU POSITION
ENTER
ESC RESET
PAGE UP VOLUME
MAGNIFY
AUTO BLANK RGB SEARCH
STANDBY/ON
1Press the POSITION button
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
2Use the , , , buttons to adjust
the position
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation.  (Even if you dont do...

19
ENGLISH
The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
NOTE
1
USING THE AUTOMATIC ADJUSTMENT FEATURE
Press the AUTO button
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be...

20
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
NOTE
CORRECTING KEYSTONE DISTORTIONS
1Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion. 
2Use the , buttons to select the
direction of distortion to correct ( / )
3Use the,buttons to correct the
distortion
Press the KEYSTONE button again to close the...