3M Mp8770 Operators Guide

							© 3M 2000 3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
ENGLISH
19
4.10 OPT.
The OPT. sub-menu allows you to control communication function.
Figure 4.9  OPT Adjustment Screens
INPUTOPT. IMAGESETUP
COM. BITSCOM. SPEED
LANGUAGETIMER
AUTO OFFSYNC ON G
INPUT
INPUTOPT. IMAGESETUP
COM. SPEED
LANGUAGETIMER
AUTO OFFSYNC ON G
INPUT
7N1
8N1COM. BITS
INPUTOPT. IMAGESETUP
COM. SPEED
TIMER
AUTO OFFSYNC ON G
INPUT
ENGLISH
FRANCAIS
DEUTSCH
ESPANOL
ITALIANO
NORSK
NEDERLANDS
JAPANESELANGUAGE
COM. BITS
INPUTOPT. IMAGESETUP
COM. SPEED
TIMER
AUTO OFF
INPUT
TURN ON
TURN OFF
COM. BITS
SYNC ON G
LANGUAGE
EPS-137A
INPUTOPT. IMAGESETUP
COM. SPEED
LANGUAGE
SYNC ON G
INPUT
AUTO OFF
COM. BITSTIMER
0 min.
INPUTOPT. IMAGESETUP
COM. SPEED
LANGUAGEAUTO OFFSYNC ON G
INPUT
TIMERCOM. BITS
10 min.
INPUTOPT. IMAGESETUP
COM. BITS
LANGUAGETIMER
AUTO OFFSYNC ON G
INPUT
1200
2400
4800
9600
19200COM. SPEED
Adjustment
Screen
1200
7N1
—
—
— Selects the data speed of transmission.
Selects the data format of transmission.
7N1... 7 data-bits, No parity, 1 stop bit.
8N1... 8 data-bits, No parity, 1 stop bit.
Sets the timer ( 0-99 minutes).
Selects the language on-screen menu. (English, French, German,
Spanish, Italian, Norwegian, Netherlands, Japanese)
Selects how long projector will stay on in minutes, if no input is detected.
Select 0 to disable this function.
Sets the SYNC on G function to ON/OFF (suppor ts older monitors). COM. SPEED
COM. BITS
TIMER
LANGUAGE
AUTO OFF
SYNC ON G
Value Default
Downloaded From projector-manual.com 3M Manuals 
						

							3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
© 3M 2000
ENGLISH
20
4
5
6
MP8770
+ZOOMM
UTE
IN
PU
T
STANDBY ON
RESET
POWER LAMPTEMPM
ENU+FOCUS
MP8770PORTABLE PROJECTOR
EPS-132A
Power
1
2
3
5.1 Cleaning the Air Filter
✔ Note
Clean the air filter about every 50 hours. If air is restricted due to dust accumulation on filter, the projector may
shut down due to overheating.
1. Turn off the MAIN POWER SWITCH of the projector and disconnect power cord (1). Let cool for 20
minutes.
2. Push tab (2) and remove the air filter cover (3) from the front of the projector.
3. Lift retainer wire (4) and carefully remove foam air filter (5).
4. Vacuum (6) dust and dirt from filter.
5. Re-install air filter and replace air filter door.
Section 5: Maintenance
Figure 5.1  Remove Air Filter
Downloaded From projector-manual.com 3M Manuals 
						

							© 3M 2000 3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
ENGLISH
21
6.1 Lamp
The following symptoms may indicate a lamp in need of replacement:
•LAMP indicator lights up red.
•“CHANGE THE LAMP” message appears on the screen.
✔ Note
This lamp contains mercury. Consult your local hazardous waste regulations and dispose of this lamp in a
proper manner.
6.2 Display Lamp Operation Hours
To determine the lamp operation hours, follow these steps:
1. While the projector is running, press and hold the TIMER button on the remote control for 3 seconds.
2. The operating time of the lamp will be displayed.  The message “CHANGE THE LAMP, AFTER
REPLACING LAMP RESET THE LAMP TIMER” will appear after the lamp operating hours have reached
the end of the normal lamp life. The message “POWER WILL TURN OFF AFTER 
20 HOURS” will appear
when 20 or less lamp hours remain. The number of hours left until shut down will decrease until 
0 hour is
reached, then power will be turned off.
✔ Note
After normal lamp operating time has expired, the projector will only run for 10 minute intervals when restarted
until the lamp is replaced and the lamp timer is reset. The message “CHANGE THE LAMP” will blink at
projector start up to remind you to change the lamp.
6.3 Reset Lamp Hours
1. To display the total lamp hours, press and hold for 3 seconds, the RESET button on the projector or Timer
button on the remote control.
2. To reset the lamp timer, press the RESET button on the projector or MENU button on the remote while the
total lamp hours are displayed. Use the arrow button on the projector or the DISC PAD to select 0 (or
CANCEL).
Section 6: Lamp
Downloaded From projector-manual.com 3M Manuals 
						

							3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
© 3M 2000
ENGLISH
22
✔ Note
For maximum lamp life, do not apply shock, handle or scratch the lamp glass when it is hot. Also, do not use an
old or previously used lamp as a replacement lamp.
1.Remove lamp access door: The lamp access door is located on the bottom of the machine. Use a screwdriver to
unscrew the cover retaining screw (1) and gently remove the cover (2) and set it aside.
2.Retaining screws:  Use a screwdriver to unscrew the lamp module retaining screws. (3)
✔ Note
All lamp module screws must be loosened.  These screws are self-containing screws that cannot be removed
from the lamp module or access door.
3.Remove lamp module:  Carefully slide the lamp module out (4) using steady pressure.
4.Insert lamp module:  Carefully insert (4) the new lamp module. Ensure that it is fully seated. Tighten the
lamp module retaining screws (3) to secure the lamp module in place.
Insert the hinge tabs on the bottom of the lamp access door, then close and tighten the retaining screw
(1) to secure the door.
✔ Note
Reset the lamp operation hours. See Section 6.3 for details.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the
lamp.
To reduce the risk of cuts to fingers and damage to internal components, use caution when removing lamp
glass that has failed and shattered into sharp pieces.
  Caution
1
2
33
4
EPS-98A
  WARNING
To reduce the risk of electrical shock, always turn off projector and disconnect power cord before changing
lamp.
6.4 Replacing the Lamp
To reduce the risk of cuts to fingers from sharp metal fittings and/or decreasing image quality by touching the
lens, do not insert hand into the empty lamp compartment when the lamp has been removed.
  Caution
Figure 6.1  Lamp Module
Downloaded From projector-manual.com 3M Manuals 
						

							© 3M 2000 3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
ENGLISH
23
Power cannot be turned
on.
No picture and sound.
Sound is heard with no
picture.
Picture is displayed with
no sound.
Color is weak and tint  is
incorrect.
Picture is dark.
Picture is not clear.
LAMP indicator lights
red.
LAMP indicator blinks
red.
TEMP indicator blinks
red.
Section 7: Troubleshooting
•The main power is not turned on.
•The power cord is disconnected.
•60 seconds have not elapsed since
the power was turned off.
•The setting of the input source is
not  correct.
•RGB/Video/Audio wiring to
projector is not correct.
•RGB/Video/Audio wiring to
projector is not correct.
•The brightness is set fully to dark.
•Lens cap is on.
•Audio wiring to projector is not
correct.
•The volume is set to minimum.
•The unit is muted.
•PinP is on and audio is switched to
VIDEO mode.
•The color and tint have been
adjusted incorrectly.
•The brightness and contrast has
not been adjusted correctly.
•The lamp needs to be replaced.
•Projector is out of focus.
•Lamp will not ignite.
• Temperature inside projector is too
hot.
•Lamp access door on bottom of
case is open.
• The lamp operating hours have
reached maximum operating hours.
• Cooling fan not operating.
Cause
Symptom
•Turn on the MAIN POWER SWITCH.
•Insert the power cord into an AC socket.
•Wait 60 seconds before turning on power.
•Set the correct input using the input select button of
the projector or the remote control.
•Connect the cable to correct input/output source.
•Connect the cable to correct input/output source.
•Press the MENU button and increase BRIGHTNESS.
•Remove lens cap.
•Connect the cable to correct input/output source.
•Press the VOL button to increase Volume.
•Press the MUTE button.
•Press VOLUME and move DISC PAD to switch to
audio input.
• Adjust the color and tint correctly.
•Adjust the brightness and contrast correctly.
•Replace the lamp with a new one.
• Adjust the focus and H PHASE.
• Turn off power and let cool for 20 minutes, then
restart.
• If problem persists call your dealer.
• Clear blocked ventilation holes.
• Clean air filter.
• Ensure lamp access door is closed.
• Replace the lamp.
• Contact your dealer.
Solution
7.1 Symptom/Solution Table
Downloaded From projector-manual.com 3M Manuals 
						

							3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
© 3M 2000
ENGLISH
24
NO INPUT IS
DETECTED.
SYNC is out of Range.
CHANGE THE LAMP.
CALL A  MAINTENANCE
PERSON.
CHANGE THE  LAMP.
CALL A MAINTENANCE
PERSON.
THE POWER WILL
TURN OFF AFTER *hr.
CHANGE THE  LAMP.
(Blinking message)The projector is not detecting a signal.
The horizontal frequency of input signal
exceeds projector capability.
Nearing end of normal lamp operation
time.
Remaining lamp operation time = 20
hours or less.
*Indicates number of hours until power
turns off automatically.
Normal lamp operating time has
expired. Safety feature shuts projector
down after 10 minutes.Check cable connections to input device. Input device
not connected to this input mode, switch to next mode.
Switch projector to correct resolution.
See Appendix A.5
Change the projector lamp and reset the lamp
operation hours to zero.
Change the projection lamp and reset the lamp
operation hours to zero.
Change the projector lamp and reset the lamp
operation  hours to zero.
7.2 Message/Solution Table
Error Message
DisplaysCause Solution
Downloaded From projector-manual.com 3M Manuals 
						

							© 3M 2000 3M™ Multimedia Projector MP8755/MP8755L/MP8770/MP8770L
ENGLISH
25
Section 8: Accessories
8.1 Service Information
For product information, product assistance, service information, or to order accessories, please call:
In U.S. or Canada:  1-800-328-1371
In other locations, contact your local 3M Sales office.
AccessoriesPart Number
Ultra-high performance lamp module, 190 W. . . . . . . . . . . . . . . . . . . . . 
78-6969-8919-9
Power cord (US). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
DY-0205-1356-9
Power cord (UK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
DY-0205-1355-1
Power cord (Eu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
DY-0205-1354-4
VGA cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-3401-5
MAC adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-3308-2
S-video cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-3238-1
3-conductor video/audio cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-3234-0
Serial mouse cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-8107-3
PS/2 mouse cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-8105-7
ADB mouse cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-8016-5
Stereo mini jack cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-8104-0
Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-8246-9
Not Included with Basic PacketPart Number
Ceiling mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-6969-8748-2
Adjustable height suspension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-6969-8312-7
Shipping case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-6969-8584-1
Soft carry case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-6969-8585-8
RS-232 control cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-3312-4
USB mouse cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 
78-8118-8186-7
Document Camera - 120 VAC 60 Hz (optional). . . . . . . . . . . . . . . . . . . 
78-6969-8578-3
Document Camera - 220 VAC 50 Hz (optional). . . . . . . . . . . . . . . . . . . 
78-6969-8724-3
How to Order
Please order these parts through your dealer, or contact 3M Customer Service at the following number:
In U.S. or Canada: 1-800-328-1371
In other locations, contact your 3M Sales office.
----------------------------------------------------------------------------------------------------------------------------------------
The contents of this manual are subject to revision without prior notice.
3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the
information contained in this manual.
Reproduction of this manual in any form without prior permission is strictly prohibited.
3M will replace the manual if any pages are missing or collated incorrectly.
Downloaded From projector-manual.com 3M Manuals 
						

							3M Austin Center 
Building A145-5N-01 
6801 River Place Blvd. 
Austin, TX 78726-90003M Canada 
P.O. Box 5757 
London, Ontario 
N6A 4T13M Mexico, S.A. de C.V. 
Apartado Postal 14-139 
Mexico, D.F.  07000 
Mexico 3M Europe 
Boulevard de lOise 
95006 Cerge Pontoise Cedex 
France
Litho in USA
© 3M 2000
78-6970- 9041-9 Rev. BPrinted on 50% recycled wastepaper,
including 10% post-consumer
Important Notice 
All statements, technical information, and recommendations related to 3M\
’s products are based on information believed to be reliable, but the accuracy 
or completeness is not guaranteed Before using this product, you must ev\
aluate it and determine if it is suitable for your intended application.  You 
assume all risks and liability associated with such use.  Any statements\
 related to the product which are not contained in 3M’s current publications, or 
any contrary statements contained on your purchase order shall have no f\
orce or effect unless expressly set forth in a written agreement signed by an 
authorized officer of 3M.
Warranty and Limited Remedy.   This product will be free from defects in material and manufacture for\
 a period of two years from the date of
purchase .  3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLI\
ED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.   If this product is defective within the warranty period stated above, \
your
exclusive remedy shall be, at 3M’s option, to replace or repair the 3\
M product or refund the purchase price of the 3M product.
Limitation of Liability.  Except where prohibited by law, 3M will not be\
 liable for any loss or damage arising from this 3M product, whether 
direct, indirect, special, incidental or consequential regardless of the\
 legal theory asserted. 
Let us help you make the most of your next presentation.  We offer every\
thing from presentation supplies to tips for better meetings.  And were the only 
transparency manufacturer that offers a recycling program for your used \
transparencies.  For late-breaking news, handy reference  and free product samples, call 
us toll-free in the continental United States and Canada, 24 hours a day\
, or visit our Internet Website.
QR462 71
Downloaded From projector-manual.com 3M Manuals