3M MP7640 Multimedia Projector Operators Manual

							113M™ Multimedia Projector MP7640
© 3M IPC 2000
MENU
SELECT
STANDBY/ON VIDEO
POSITION
MAGNIFY FREEZE VOLUME
MUTE
BLANK TIMER AUTORGB
MENURESET
Section 2: Product Description
STANDBY/ON
Turn on Main Power switch.
Press STANDBY/ON button to
begin projection mode (lamp on)
or press and hold button for one
second to switch to standby
mode (lamp off).
MENU SELECT
Press to select menu items.
MENU Buttons
Press to navigate among menu
items.
MENU
Press to display the menu
screen.
MAGNIFY*
Press MAGNIFY (+) to enlarge
the center of the display image.
Press again to enlarge image to
maximum of 4x magnification.
Press MAGNIFY (-) to reduce
the display image size.  Press
third button to return to normal
image size.  (Can be used with
the POSITION button to select
the image area being magnified.)
BLANK
Press button to turn ON/OFF
the screen blanking function.
VIDEO and RGB
Press the VIDEO or RGB button to select the
input source. Press again to select the next
source.
POSITION*Press button, then use Menu directional
buttons to move image up, down, left or right.
(RGB signal only).
RESET*For menu screens, press button to return to
initial settings.
FREEZE*Press button to turn ON/OFF the freeze
image function.
VOLUME*
Press upper button to increase speaker
volume. Press lower button to decrease
speaker volume.
MUTE*Press button to turn the speaker sound
ON/OFF.
TIMER*Press button to turn the menu screen timer
ON/OFF. The timer does not display when
the BLANK function is active.
AUTO*
Press the AUTO button to activate the auto
sync function. The message “AU T O  I N
PROGRESS” will display for several
seconds as the projector adjusts the V.
POSIT, H.POSIT. H.PHASE, & H. SIZE
settings.
The Auto Sync function will not operate
under the following conditions:
•Initial screen message NO INPUT IS
DETECTED or SYNC IS OUT OF
RANGE is displayed.
•FREEZE and MAGNIFY functions
have not been turned off prior to
pressing AUTO button.
•Software application running on your
computer is not set to maximum
screen size prior to pressing AUTO
button.
*This button will not function if the
messages “NO INPUT IS DETECTED”
or “SYNC IS OUT OF RANGE” are displayed.
Remote Control Transmitter Identification
Figure 2.3 Basic Remote Control Transmitter 
						

							3M™ Multimedia Projector MP764012© 3M IPC 2000
Changing Remote Control Battery
This remote control transmitter uses a lithium battery located in a sliding holder inserted into the bottom of
the transmitter.
1. Turn the remote control transmitter over to access the battery holder.
2. Push the smaller tab inward as indicated below.
3. Slide the battery holder out of the bottom of the transmitter.
4. Lift the battery out of the holder and replace with the new battery. Make sure the “+” side is facing up.
5. Slide the holder back into the transmitter until the tabs snap into place.
Section 2: Product Description
Caution• Avoid excessive heat and humidity.
• Do not mix old and new batteries or different types of batteries.
CautionThis battery contains lithium. Consult your local hazardous waste regulations and
dispose of this battery in the proper manner.
A
Ta bBattery 
						

							133M™ Multimedia Projector MP7640
© 3M IPC 2000
1. Press and hold the STANDBY/ON button        for one second. The ON indicator blinks orange and
the lamp turns off. After approximately one minute, the fan stops and the indicator stays orange.
2.Turn off the MAIN POWER SWITCH.
3.Close the sliding lens door.
Caution
Projector Start-up
Section 3: Basic Operations
Figure 3.1 Projector Controls
1. Make all equipment and cable connections with the power off.
2. Turn on the MAIN POWER SWITCH       of the projector. The ON indicator will light up orange.
3. Press the STANDBY/ON button       . The ON indicator will blink green during warm-up and lamp
ignition, then stay green to indicate correct operation. When power is turned off, there is a 60-second
reset period before the STANDBY/ON button will function again.
4. Turn on all connected equipment. (Refer to “System Set-up—Connecting to Various Equipment,”
page 10.)
5. Open sliding lens door.
6. Press the INPUT button      on the projector or the INPUT SELECT (VIDEO or RGB) button on the
remote control transmitter to select the source of the signal to be projected on the screen. The
selected signal input is displayed at the bottom right of the screen.  The display will show the last
selected input source before power was turned off.
7. Adjust picture size using the projection lens Zoom knob. Adjust focus using the projection lens Focus
ring.
Projector Shutdown
Do not turn off the POWER SWITCH before pressing the STANDBY/ON button.
After the STANDBY/ON button is pressed, the fan rotates for about one minute to
cool the projector.
STANDBY/ONINPUTMUT 
						

							3M™ Multimedia Projector MP764014© 3M IPC 2000
How to Use Height Adjustment Foot
Section 4: Adjustments and Functions
Adjust the image elevation and projection angle (within 0 to 10°) using the height adjustment foot at the
front of the projector.
1. Raise the front end of the projector so the foot is not touching the tabletop.
2. Push the lock button on the left side of the projector to unlock the foot.
3. Extend or retract the foot to the desired height.
4. Release the lock button to lock the foot into position.
5. For finer adjustment, rotate the tilt adjustment knob on the left rear foot of the projector.
Figure 4.1 Height Adjustment
CautionDo not unlock the foot adjuster if the projector is not supported.
Height
Adjustment
FootLock
ButtonTilt
Adjustment
Knob 
						

							153M™ Multimedia Projector MP7640
© 3M IPC 2000
Section 4: Adjustments and Functions
Plug & Play Function
Plug & Play is a system configured with peripheral equipment (including a computer and display), and a
compatible operating system. This allows the user to connect various peripheral equipment successfully
without having to adjust settings manually. The equipment and projector exchange this information automati-
cally. This projector is VESA DDC (Display Data Channel) 1/2B compatible. Plug & Play is possible by
connecting to a computer that is VESA DDC compatible.
✔ Note: Use the RGB cable included with this projector when using plug & play. With other
cables, pins (12) - (15) are sometimes not connected (effective only for RGB1).
Freeze Function
The Freeze function is used to display (freeze) a single frame of the image being projected. This function can
be used with the Magnify function to freeze the image and then enlarge (magnify) part of the image to view it
in greater detail. Press the FREEZE button repeatedly to engage or disengage this function.
✔ Note: The FREEZE function will turn off during the operation of the MENU, FOCUS,
VOLUME, MUTE, BLANK, TIMER, AUTO or POSITION functions.
Magnify Function
The Magnify function is used to enlarge a portion of the projected image. Press the MAGNIFY (+) button to
magnify the center of the displayed image. Press again to magnify up to 4x. Press the MAGNIFY (-) button to
reduce image size. Press OFF to return to normal image size. To move the display area being magnified, press
the POSITION button, then use the DISC PAD to move the magnified area up, down, left or right.
✔ Note: To return to normal display, press the MAGNIFY OFF button. The MAGNIFY function
will turn off during the operation of the KEYSTONE or AUTO functions. 
						

							3M™ Multimedia Projector MP764016© 3M IPC 2000
Section 4: Adjustments and Functions
Menu Navigation
Factory Default Setting:
To reset a single item from SETUP menu:
1. Select the adjustment item (Bright, Contrast...).
2. Press the RESET button.  Only the selected item
resets. 1. Press MENU disk button on projector or remote control MENU buttons.
On-screen menus are displayed on the projected image.
2. Select the menu to be adjusted using the MENU disk button or remote control Menu buttons           .
Selected Menu is then highlighted.
3. Select the menu item to be adjusted using the MENU disk button or any of the remote control
Menu buttons                     .
Highlighted items may be adjusted.
✔ Note: Separate settings are provided for the VIDEO and RGB input terminals.  Adjustments
are saved after shutdown.
Figure 4.2 Menu disk button on projector and Menu buttons from remote control transmitter
Figure 4.3 Default Settings
MENU
SELECT
BRIGHT
SETUP
CONTRAST
SHARPNESS
COLOR
TINT
COLOR BAL R
COLOR BAL B
INPUTIMAGEOPT.
Press MENU SELECT on the remote control to view the full menu or just the selected menu item. When only
the selected menu item is displayed, the other menu items are displayed by pressing the            buttons.
BRIGHT 
						

							173M™ Multimedia Projector MP7640
© 3M IPC 2000
Section 4: Adjustments and Functions
Figure 4.4 RGB signal input Figure 4.5 Video signal input
*Auto Sync Function: Press the AUTO button on the remote control to engage the automatic sync function.
The message “AUTO IN PROGRESS” will display for several seconds as the projector adjusts the V. POSIT,
H.POSIT., H.PHASE, and H. SIZE settings. Auto Sync can also be executed from the control panel key pad.
Press and hold the RESET button, then press the INPUT button.
✔ Note:
• TINT cannot be adjusted with a PAL or M-PAL video signal input.
• TINT, COLOR, and SHARPNESS cannot be adjusted with an RGB signal input.
• V. POSIT, H. POSIT, H. PHASE, and H. SIZE cannot be adjusted with a VIDEO
  signal input.
• Menu operation is not possible during Freeze functions.
• Displaying the SETUP submenu will cancel the Magnify and Freeze functions.
. SETUP Submenu
The SETUP sub-menu is used to adjust and move the image position. The projector will display either the
RGB (Figure 4.4) or Video (Figure 4.5) submenu, according to the input source being projected.
Adjustment Item Details of Adjustment Freeze On Magnify On Both On
BRIGHT
   Dark  Bright Adjustable Adjustable Adjustable
(BRIGHTNESS)
CONTRAST  Lower  Higher Adjustable Adjustable Adjustable
V.POSITMoves the picture up or down.* Not Adjustable Not Adjustable Not Adjustable
(V.POSITION)
H.POSIT
Moves the picture left or right.* Not Adjustable Not Adjustable Not Adjustable
(H.POSITION)
H.PHASEDecreases the picture flicker.* Not Adjustable Adjustable Not Adjustable
H.SIZEWidens or Narrows the horizontal Not Adjustable Not Adjustable Not Adjustable
size of picture.*
SHARPNESS    Soft  Sharp Not Adjustable Adjustable Not Adjustable
TINT     Red  Green Not Adjustable Adjustable Not Adjustable
COLOR  Less  More Not Adjustable Adjustable Not Adjustable
COLOR BAL R  Less red  More red Adjustable Adjustable Adjustable
COLOR BAL B  Less blue  More blue Adjustable Adjustable Adjustable
ASPECT4:3, 4:3 small, 16:9 Not Adjustable Not Adjustable Not Adjustable
SETUP
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
INPUTIMAGEOPT.
121
57
800
7
SETUP
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H SIZE
COLOR BAL R
COLOR BAL B
INPUTIMAGEOPT. 
						

							3M™ Multimedia Projector MP764018© 3M IPC 2000
Section 4: Adjustments and Functions
INPUT Submenu
The INPUT submenu is used to select the RGB or video input source. The RGB values are shown in Figure
4.6. The Video values are shown in Figure 4.7.
Figure 4.6 RGB Input Submenu
Figure 4.7 Video Input Submenu
Adjustment
Area
RGB
Video
AutoValue
Displays the following RGB inputs:
FH:  horizontal sync frequency
FV:  vertical sync frequency
Selects the VIDEO signal format Auto,
NTSC, PAL, SECAM,
 NTSC 4.43, M-PAL, N-PAL
Selects EXECUTE or CANCEL for
Auto signal input detection.
INPUTIMAGEOPT.SETUP
RGBFH: 48.3 KHz
FV: 60 Hz
VIDEO
AUTO
INPUTIMAGEOPT.SETUP
AUTO
NTSC
PAL
SECAM
NTSC4.43
M-PAL
N-PAL
RGB
AUTO VIDEO
Figure 4.8 Auto Input Submenu
INPUTIMAGEOPT.SETUP
RGB
AUTOEXECUTE
CANCEL
VIDEO 
						

							193M™ Multimedia Projector MP7640
© 3M IPC 2000
IMAGE Submenu
The IMAGE submenu is used to change the image characteristics.
Figure 4.9 Image Adjustment Screens
Adjustment                                                         Value
Screen
KEYSTONE
Reduce distortion Reduce distortion
at bottom of image. at top of image.
BLANKSelects the blank screen color: red, orange, green, blue, purple, white or black.
MIRRORInverts the picture horizontally or vertically.
H:  INVERT Inver ts the picture horizontally.
V:  INVERT Inverts the picture vertically.
H&V:  INVERT Inverts the picture horizontally and vertically.
STARTUPEnable / Disable startup screen.
When canceled, the background color will change to blue.
Section 4: Adjustments and Functions
INPUTIMAGEOPT.SETUP
BLANK
MIRROR
START UP
INPUTINPUTIMAGEOPT.SETUP
KEYSTONE
MIRROR
START UP
INPUT
BLANK
INPUTIMAGEOPT.SETUP
KEYSTONE
START UP
INPUT
MIRROR
KEYSTONE
BLANK
TURN ON
TURN OFF
INPUTIMAGEOPT.SETUP
KEYSTONE
INPUT
BLANK
MIRROR
START UP
±0
NORMAL
H: INVERT
V: INVERT
H&V: INVERT 
						

							3M™ Multimedia Projector MP764020© 3M IPC 2000
OPT. Submenu
The OPT. submenu allows you to control communication function.
Figure 4.10 OPT Adjustment Screens
Adjustment                                           Value Default
Screen
VOLUMEAdjusts the loudness of audio coming through the speaker.8
Selects the background color in which the menu system will be displayed.
MENU COLORChoice of red, orange, green, blue, purple, white and black. Blue
(All menus have white text except white menu, which will have black.)
TIMERSets the timer ( 0-15 minutes).—
LANGUAGESelects the language on-screen menu. (English, French, German,—
Spanish, Italian, Norwegian, Netherlands, Japanese, and Portuguese)
AUTO OFFSelects how long projector will stay on in minutes, if no input is detected.—
Select 
0 to disable this function.
SYNC ON GSets the SYNC on G function to ON/OFF (for older Apple computers).
Section 4: Adjustments and Functions
INPUTOPT. IMAGESETUP
MENU COLOR
LANGUAGE
TIMER
SYNC ON G
AUTO OFF
INPUTINPUTOPT. IMAGESETUP
VOLUME
LANGUAGE
TIMER
SYNC ON G
AUTO OFF
INPUT
VOLUME
MENU COLOR
INPUTOPT. IMAGESETUP
VOLUME
TIMER
SYNC ON G
AUTO OFF
INPUT
ENGLISH
FRAN‚AIS
DEUTSCH
ESPA„OL
ITALIANO
NORSK
NEDERLANDS
JAPANESE
PORTUGUæSLANGUAGE
INPUTOPT. IMAGESETUP
VOLUME
LANGUAGE
SYNC ON G
AUTO OFF
INPUT
TIMER
MENU COLORMENU COLOR
INPUTOPT. IMAGESETUP
VOLUME
LANGUAGE
SYNC ON G
INPUT
AUTO OFF
MENU COLOR
TIMER
INPUTOPT. IMAGESETUP
VOLUME
TIMER
AUTO OFF
INPUT
TURN ON
TURN OFF
MENU COLOR
SYNC ON G
LANGUAGE
15 min.
0 min.
8
STOP