3M Digital Projector X90w Operators Manual

							41
SCREEN Menu
Item Description
MyScreenThis item allows you to capture an image for use as a MyScreen 
image which can be used as the BLANK screen and START UP 
screen. Display the image you want to capture before executing the 
following procedure.
1. Selecting this item displays a dialog 
titled “MyScreen”. It will ask you if 
you start capturing an image from the 
current screen.
Please wait for the target image to be displayed, and press 
the ENTER button on the remote control when the image is 
displayed. The image will freeze and the frame for capturing will 
appear.
To stop performing, press the RESET or ESC button on the 
remote control. 
8VLQJWKH
x
z
{
yEXWWRQVDGMXVWV
the frame position.
Please move the frame to the position 
of the image which you want to use. The 
frame may not be able to be moved for 
some input signals.
To start registration, press the ENTER 
button on the remote control.
To restore the screen and return to the previous dialog, press the 
RESET or ESC button on the remote control.
Registration takes several minutes.
When the registration is completed, the registered screen and the 
following message is displayed for several seconds:
³0\6FUHHQUHJLVWUDWLRQLV¿QLVKHG´
If the registration failed, the following message is displayed:
³$FDSWXULQJHUURUKDVRFFXUUHG3OHDVHWU\DJDLQ´
• This item cannot be selected for an M1-D signal.
• This function cannot be selected when the TURN ON is selected 
to the MyScreen Lock item (
	below).
• This function cannot be selected when the TURN ON is selected 
to the MyScreen PASSWARD of SECURITY item in OPTION menu 
(
	49).
MyScreen Lock8VLQJWKH
x
zEXWWRQVWXUQVRQRIIWKH0\6FUHHQORFNIXQFWLRQ
TURN ON 
Ù TURN OFF
When the TURN ON is selected, the item MyScreen is locked. Use 
this function for protecting the current MyScreen.
• This function cannot be selected when the TURN ON is selected 
to the MyScreen PASSWARD of SECURITY item in OPTION menu 
(
	49).
SCREEN Menu (continued)
/[5ETGGP&Q[QWUVCTVECRVWTKPIVJKURKEVWTG!
01;55%06
/[5ETGGP/QXGVJGECRVWTGCTGC
CU[QWYCPV

467400:6456064
/[5ETGGP

L U
(continued on next page)
© 3M 2006.        3M™ Digital Projector X90w 
						

							42
SCREEN Menu
Item Description
MESSAGE8VLQJWKH
x
zEXWWRQVWXUQVRQRIIWKHPHVVDJHIXQFWLRQ
TURN ON 
Ù TURN OFF
When the TURN ON is selected, the following message function works.
“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
The indication of the input signal displayed by changing 
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the ACTIVE IRIS displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of "FREEZE" and "II" while freezing the screen by 
pressing the FREEZE button.
• When the TURN OFF is selected, please remember if the picture 
is freezing. Do not mistake freezing for a malfunction (
	22).
SOURCE NAMEEach input port for this projector can have a name applied to it.
(1) Use the 
x
z buttons on the SCREEN menu to 
select SOURCE NAME and press the 

y button. 
The SOURCE NAME menu will be displayed.
8VHWKH
x
zEXWWRQVRQWKH6285&(
NAME menu to select the port to be named 
DQGSUHVVWKH
yEXWWRQ5LJKWVLGHRIWKH
PHQXLVEODQNXQWLODQDPHLVVSHFL¿HG
The SOURCE NAME dialog will be displayed.
(3) The current name will be displayed on the 
¿UVWOLQH8VHWKH

x
z
{
y buttons and the 
ENTER or INPUT button to select and enter 
characters. The RESET button can be used to 
erase 1 character at a time. The name can be a 
maximum of 16 characters.
(4) To change an already inserted character, press 
the

xEXWWRQZKLOHWKHFXUVRULVRQWKH>$1@
row to move the cursor to the name displayed on 
WKH¿UVWOLQHDQGXVHWKH

{
y buttons to select 
character to be changed. Once a character in the 
name is selected use the 

z button to move the 
cursor back down to the character entry area to 
select and enter characters as described above.
(5) Select and press the ENTER or 
,1387EXWWRQVZKHQ
						

							43
OPTION Menu
OPTION Menu
Item Description
AUTO SEARCH
8VLQJWKH
x
zEXWWRQVWXUQVRQRIIWKHDXWRPDWLFVLJQDOVHDUFKIXQFWLRQ
TURN ON 
Ù TURN OFF
When the TURN ON is selected, detecting no signal automatically cycles 
through input ports in the following order. The search is started from the 
current port. Then when an input is found, the projector will stop searching 
and display the image.
RGB 1
Ö RGB 2
Ö M1-D
ÖMIU 
Ö COMPONENT 
Ö S-VIDEO 
Ö VIDEO 
• The MIU input is skipped, as long as no image is sent from PC on 
the “Live Mode” (
	54).
AUTO 
KEYSTONE 
8VLQJWKH
x
zEXWWRQVWXUQVRQRIIWKHDXWRPDWLFNH\VWRQHIXQFWLRQ
TURN ON 
Ù TURN OFF
TURN ON : Automatic keystone distortion correction will be 
executed whenever changing the slant of the projector.
TURN OFF : This function is disabled. Please execute the AUTO 
KEYSTONE
EXECUTE in the SETUP Menu for automatic 
keystone distortion correction.
• When the projector is suspended from the ceiling this feature will 
not function properly so select the TURN OFF.
• This function will be unavailable when the Transition Detector is 
on
(	52).
AUTO ON8VLQJWKH
x
zEXWWRQVWXUQVRQRIIWKH$87221IXQFWLRQ
TURN ON 
Ù TURN OFF
When AUTO ON is set to TURN ON, the projector’s lamp will only 
be automatically turned on when the Power switch is turned on if 
the power was turned off using the Power switch the last time the 
projector was turned off.
• After turning the lamp on by the AUTO ON function, if neither input nor 
operation is detected for about 30 minutes, the projector is turned off, even 
though the AUTO OFF function 
(	44) is disabled.
From the OPTION menu, items shown in the table below can be 
performed.
6HOHFW DQ LWHP XVLQJ WKH 
x
z FXUVRU EXWWRQV RQ WKH SURMHFWRU RU
UHPRWHFRQWURODQGSUHVVWKH
yFXUVRUEXWWRQRQWKHSURMHFWRURU
remote control, or ENTER button on the remote control to execute 
the item, except for the items LAMP TIME and FILTER TIME. 
Then perform it according to the following table./07=4)$?
5.%6


#7611((OKP
.#/26+/ J
(+.646+/ J#7615#4%*67401((

#761-;561067401((
#7611067401((
/;$76610
548+%
5%74+6; +/#) 2+%674
5672+0276
5%40
126+10#7&+1
/+7
#5;/07
(continued on next page)
© 3M 2006.        3M™ Digital Projector X90w 
						

							44
Item Description
AUTO OFF8VLQJWKH
x
zEXWWRQVDGMXVWVWKHWLPHWRFRXQWGRZQWR
automatically turn the projector off.
Long (max. 99 minutes) 
Ù Short (min. 0 minute = DISABLE)
AUTO OFF
ENABLE
1AUTO OFF
DISABLE
0
When the time is set to 0, the projector is not turned off automatically.
When the time is set to 1 to 99, and when the passed time with no-
signal or an unsuitable signal reaches at the set time, the projector 
lamp will be turned off. 
If one of the projector's buttons or the remote control buttons 
is pressed or one of the commands (except get commands) is 
transmitted to the control port during the corresponding time, 
projector will not be turned off.
Please refer to the section “Turning off the power” (
	17).
LAMP TIMEThe lamp time is the time counted after the last resetting. It is 
shown in the OPTION menu as the usage time of the lamp.
3UHVVLQJWKH5(6(7EXWWRQRQWKHUHPRWHFRQWURORUWKH
yEXWWRQ
of the projector displays a dialog. 
7RUHVHWWKHODPSWLPHVHOHFWWKH5(6(7XVLQJWKH
xEXWWRQ
RESET 
Õ CANCEL
• Please reset the lamp time only when you have replaced the lamp, 
for a suitable indication about the lamp.
• For the lamp replacement, see the section "Lamp" (
	59, 60).
FILTER TIMELVVKRZQ

3UHVVLQJWKH5(6(7EXWWRQRQWKHUHPRWHFRQWURORUWKH
yEXWWRQ
of the projector displays a dialog. 
7RUHVHWWKH
						

							45
Item Description
MY BUTTONThis item is to assign one of the following function to MY BUTTON 
1 and 2 on the remote control (
	6).
&KRRVHRURQWKH0
						

							46
Item Description
SERVICE
(continued)AUTO ADJUST
8VLQJWKH
x
zEXWWRQVHQDEOHVGLVDEOHVWKH
automatic adjustment.When DISABLE is selected, 
the automatic adjustment feature is disabled, 
although rough adjustment is automatically performed 
depending on the basic setting.
ENABLE
Ù DISABLE
• Depending on conditions, such as input image, signal cable to 
the projector, environment around the projector, etc., the automatic 
adjustment may not work correctly.  In such a case, please 
choose DISABLE to disable the automatic adjustment, and make 
adjustment manually.
GHOST
6HOHFWDFRORUHOHPHQWRIJKRVWXVLQJWKH
{
y
buttons.
2.
$GMXVWWKHVHOHFWHGHOHPHQWXVLQJWKH
x
zEXWWRQVWR
disappear ghost.
FILTER MESSAGE
8VHWKH
x
zEXWWRQWRVHWWKHWLPHUIRUWKHLQWHUYDOWR
VKRZWKHPHVVDJHIRUFOHDQLQJXSWKHDLU
						

							47
Item Description
SERVICE
(continued)KEY LOCK
8VLQJ WKH 
x
z EXWWRQV WXUQV RQRII WKH NH\ ORFN IHDWXUH :KHQ
TURN ON is selected, the buttons on the projector except the 
STANDBY/ON button are locked.
TURN ON 
Ù TURN OFF
• Please use to avoid a mischief and touching accidentally. This 
function does not have any effect on the remote control.
REMOTE RECEIV.
6HOHFWDUHPRWHVHQVRUXVLQJWKH
x
zEXWWRQ
1:FRONT 
Ù2:TOP 
Ù 3:REAR
(2) Switch it using the ENTER button
… (off) 
Ù; (on)
• A sensor cannot be turned off when the other 
two are off. Always at least one sensor is on.
REMOTE FREQ.
8VHWKH
x
zEXWWRQWRFKDQJHWKH3URMHFWRU
VUHPRWHVHQVRU
setting (
	15).
1:NORMAL 
Ù2:HIGH
Items with a checkmark are on. The factory 
default setting is for both 1:NORMAL and 2:
HIGH to be on. If the remote control does not 
function correctly set the this to either only 
1 or only 2 as described in Remote Control 
Settings (
	15).
Neither can be turned off at the same time.
INFORMATION
Selecting this item displays a dialog titled “INPUT INFORMATION”. 
It shows the information about the current input.
INPUT-INFORMATION
RGB1
1024x768 @60Hz
FRAME LOCKINPUT-INFORMATION
S-VIDEO
SECAM
AUTOINPUT-INFORMATION
COMPONENT
576i @50
SCART RGB
• The “FRAME LOCK” message on the dialog means the frame lock 
function is working. 
• The “SCART RGB” message means the COMPONENT VIDEO 
port is working as a SCART RGB input port. Please refer to the 
COMPONENT item in INPUT menu (
	33).
• This item can't be selected for no signal and sync out.
FACTORY RESET
6HOHFWLQJ5(6(7XVLQJWKHEXWWRQ
xSHUIRUPVWKLVIXQFWLRQ%\
this function, all the items in all of menus will collectively return to 
the initial setting. Note that the items LAMP TIME, FILTER TIME, 
LANGUAGE and SECURITY are not reset.
RESET 
Õ CANCEL
OPTION Menu (continued)
OPTION Menu
(4106
612
4/164%+8
064
4#4
:œ:¥:«:œ:©
(continued on next page)
4/16(43
014/#.
*+)*
064:œ:¥:«:œ:©
© 3M 2006.        3M™ Digital Projector X90w 
						

							48
Item Description
SECURITYThis projector is equipped with security functions.
User registration is required before using the security functions.
Please contact your local dealer.
1. Using Security Features
1.1 Inputting the PASSWORD
8VHWKH
x
zEXWWRQVRQWKH237,21
PHQXWRVHOHFW6(&85,7
						

							49
Item Description
SECURITY
(continued)1.3 If you have forgotten your PASSWORD
1.3-1 Follow the procedure in 1.1-1 to display the 
ENTER PASSWORD BOX.
1.3-2 While the ENTER PASSWORD BOX is 
displayed, press and hold the RESET button 
on the remote control for about 3 seconds or 
SUHVVDQGKROGWKH,1387DQG
yEXWWRQVRQ
the projector for about 3 seconds.
The 10 digit Inquiring Code will be displayed. 
• If there is no key input for about 55 seconds while 
the Inquiring Code is displayed the menu will close. 
If necessary repeat the process from 1.3-1.
1.3-3 Contact your dealer with the 10 digit Inquiring Code. Your PASSWORD 
HG
2. Using the MyScreen PASSWORD Function
The MyScreen PASSWORD function can be used to prohibit access to the 
MyScreen function and prevent the currently registered MyScreen image 
from being overwritten.
2.1 Turning on the MyScreen PASSWORD
Function
8VHWKH
x
zEXWWRQVRQWKH6(&85,7
						

							50
Item Description
SECURITY
(continued)
2.2-4 Move the cursor to the right side of the 
CHECK PASSWORD BOX and press the 

yEXWWRQWRGLVSOD\WKH3$66:25IRU
about 20 seconds, please make note of the 
PASSWORD during this time. 
Pressing the ENTER button on the remote control 
or INPUT button on the projector will return to 
MyScreen PASS WORD on/off menu.
When a PASSWORD is set for MyScreen:
•The MyScreen registration function (and menu) will be unavailable.
•The MyScreen Lock function (and menu) will be unavailable.
•The START UP setting will be locked on MyScreen (and the menu will be 
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of both  
functions.
•Please do not forget your MyScreen PASSWORD.
2.3 Turning the PASSWORD off
2.3-1 Follow the procedure in 2.1-1 to display the MyScreen PASSWORD
on/off menu.
2.3-2 Select TURN OFF to display the ENTER PASSWORD BOX (large). 
Enter the registered PASSWORD and the screen will return to the 
MyScreen on/off menu.
If an incorrect PASSWORD is input the menu will close. If necessary repeat 
the process from 2.3-1.
2.4 If you have forgotten your PASSWORD
2.4-1 Follow the procedure in 2.1-1 to display the MyScreen PASSWORD 
on/off menu.
2.4-2 Select TURN OFF to display the ENTER 
PASSWORD BOX (large). The 10 digit 
Inquiring Code will be displayed inside the 
BOX.
2.4-3 Contact your dealer with the 10 digit Inquiring 
Code. Your PASSWORD will be sent after 
\RXUXVHUUHJLVWUDWLRQLQIRUPDWLRQLVFRQ¿UPHG
3. Using the PIN LOCK Function
PIN LOCK is a function which prevents the projector from being used unless 
a registered Code is input.
3.1 Registering the PIN Code
8VHWKH
x
zEXWWRQVRQWKH6(&85,7