3M Digital Projector X64 Operators Manual

							
61
6SHFL
						

							
1
X64
Operator's GuideTECHNICAL
Resolution (H x V) H. frequency (kHz) V. frequency (Hz) Rating Signal mode720 x 400 37.9 85.0 VESA TEXT
640 x 480 31.5 59.9 VESA VGA (60Hz)
640 x 480 37.9 72.8 VESA VGA (72Hz)
640 x 480 37.5 75.0 VESA VGA (75Hz)
640 x 480 43.3 85.0 VESA VGA (85Hz)
800 x 600 35.2 56.3 VESA SVGA (56Hz)
800 x 600 37.9 60.3 VESA SVGA (60Hz)
800 x 600 48.1 72.2 VESA SVGA (72Hz)
800 x 600 46.9 75.0 VESA SVGA (75Hz)
800 x 600 53.7 85.1 VESA SVGA (85Hz)
832 x 624 49.7 74.5 Mac 16” mode
1024 x 768 48.4 60.0 VESA XGA (60Hz)
1024 x 768 56.5 70.1 VESA XGA (70Hz)
1024 x 768 60.0 75.0 VESA XGA (75Hz)
1024 x 768 68.7 85.0 VESA XGA (85Hz) 1152 x 864 67.5 75.0 VESA
1152 x 864 (75Hz)
1280 x 960 60.0 60.0 VESA1280 x 960 (60Hz)
1280 x 1024 64.0 60.0 VESA SXGA (60Hz)1280 x 1024 80.0 75.0 VESA SXGA (75Hz)
1280 x 1024 91.1 85.0 VESA SXGA (85Hz)
1600 x 1200 75.0 60.0 VESA UXGA (60Hz) 1280 x 768 47.7 60.0 VESA W-XGA (60Hz)
1400 x 1050 65.2 60.0 VESA SXGA+ (60Hz)
NOTE   • Be sure to check jack type, signal level, timing and resolution \
before connecting this projector to a PC.
• Some PCs may have multiple display screen modes. Use of some of the\
se 
modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possibl\
e in some 
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA 
(1600x1200), the signal will be converted to the projector’s panel resolution 
before being displayed. The best display performance will be achieved if the 
resolutions of the input signal and projector panel are identical.
• Automatically adjustment may not function correctly with some input sign\
als.
• The image may not be displayed correctly when the input sync signal is a\
  composite sync or a sync on G.
Example of PC signal 
 \251 3M 2007.  All Rights Reserved.   
						

							
2
Initial set signals
Initial set signals
The following signals are used for the initial settings. The signal timing of some 
PC models may be different. In such case, adjust the items V POSITION and H 
POSITION in IMAGE menu. 
computerSignal +RUL]RQWDOVLJQDOWLPLQJV
computer
Signal Vertical 
signal timing (lines)
(A) (B) (C) (D) (a) (b) (c) (d)
TEXT 2.0 3.0 20.3 1.0 TEXT 3 42 400 1
VGA (60Hz) 3.8 1.9 25.4 0.6 VGA (60Hz) 2 33 480 10
VGA (72Hz) 1.3 4.1 20.3 0.8 VGA (72Hz) 3 28 480 9
VGA (75Hz) 2.0 3.8 20.3 0.5 VGA (75Hz) 3 16 480 1
VGA (85Hz) 1.6 2.2 17.8 1.6 VGA (85Hz) 3 25 480 1
SVGA (56Hz) 2.0 3.6 22.2 0.7 SVGA (56Hz) 2 22 600 1
SVGA (60Hz) 3.2 2.2 20.0 1.0 SVGA (60Hz) 4 23 600 1
SVGA (72Hz) 2.4 1.3 16.0 1.1 SVGA (72Hz) 6 23 600 37
SVGA (75Hz) 1.6 3.2 16.2 0.3 SVGA (75Hz) 3 21 600 1
SVGA (85Hz) 1.1 2.7 14.2 0.6 SVGA (85Hz) 3 27 600 1
Mac 16" mode 1.1 3.9 14.5 0.6 Mac 16" mode 3 39 624 1
XGA (60Hz) 2.1 2.5 15.8 0.4 XGA (60Hz) 6 29 768 3
XGA (70Hz) 1.8 1.9 13.7 0.3 XGA (70Hz) 6 29 768 3
XGA (75Hz) 1.2 2.2 13.0 0.2 XGA (75Hz) 3 28 768 1
XGA (85Hz) 1.0 2.2 10.8 0.5 XGA (85Hz) 3 36 768 1 1152 x 864  (75Hz) 1.2
2.4 10.7 0.6 1152 x 864 
(75Hz) 3 32 864 1
1280 x 960  (60Hz) 1.0
2.9 11.9 0.9 1280 x 960 
(60Hz) 3 36 960 1
SXGA (60Hz) 1.0 2.3 11.9 0.4 SXGA(60Hz) 3 38 1024 1
SXGA (75Hz) 1.1 1.8 9.5 0.1 SXGA (75Hz) 3 38 1024 1
SXGA (85Hz) 1.0 1.4 8.1 0.4 SXGA (85Hz) 3 44 1024 1
UXGA (60Hz) 1.2 1.9 9.9 0.4 UXGA (60Hz) 3 46 1200 1
W-XGA (60Hz) 1.7 2.5 16.0 0.8 W-XGA (60Hz) 3 23 768 1
SXGA+ (60Hz) 1.2 2.0 11.4 0.7 SXGA+ (60Hz) 3 33 1050 1 Back porch (B)  Front porch (D)  Back porch (b)  Front porch (d)
Active video (C)Data Data
H. Sync.  V. Sync.
Sync (A)   Sync (a)Active video (c)
3M\231 Digital Projector X64 
 \251 3M 2007.  All Rights Reserved.   
						

							
3

Connection to the ports
ACOMPUTER IN1, BCOMPUTER IN2, CMONITOR OUT
 D-sub 15pin mini shrink jack
‡9LGHRVLJQDO5*%VHSDUDWH$QDORJ9SS

terminated (positive)
• H/V. sync. Signal: TTL level (positive/negative)
• Composite sync. Signal: TTL level
Pin Signal Pin Signal
1 Video Red 10 Ground
2 Video Green 11 (No connection)
3 Video Blue
12
A: SDA (DDC data)
B,C: (No connection)4(No connection)
5 Ground 13 H. sync / Composite sync.
6 Ground Red 14 V. sync.
7 Ground Green
15
A: SCL (DDC clock)
B,C: (No connection)8Ground Blue
9 (No connection) - -
Connection to the ports
A
CB
 






 



3M\231 Digital Projector X64 
 \251 3M 2007.  All Rights Reserved.   
						

							
4
Connection to the ports (continued)
4
3 21
HVIDEO
RCA jack
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43
‡“9SS
WHUPLQDWRU
GS-VIDEO
Mini DIN 4pin jack
Pin Signal
1 &RORUVLJQDO9SS176&EXUVW
WHUPLQDWRU
&RORUVLJQDO9SS3$/6(&$0EXUVW
WHUPLQDWRU
2 %ULJKWQHVVVLJQDO9SS
WHUPLQDWRU
3 Ground
4 Ground
FD
H
EG
COMPONENT VIDEO D Y,  E Pb/Cb, F Pr/Cr
RCA jack x3
• System: 525i(480i), 525p(480p), 625i(576i), 750p(720p),1125i(1080i)
Port Signal
Y &RPSRQHQWYLGHR
						

							
5

Connection to the ports (continued)
IAUDIO IN1, JAUDIO IN2
Ø3.5 stereo mini jack
‡P9UPVNŸWHUPLQDWRU
AUDIO IN3 KL,LR
RCA jack x2
‡P9UPVNŸWHUPLQDWRU
MAUDIO OUT
Ø3.5 stereo mini jack
‡P9UPVNŸRXWSXWLPSHGDQFH
To input SCART RGB signal;
  ex.:
I
J
M
KL
To input SCART RGB signal to the projector, use a SCART to RCA cable. 
Connect the plugs refer to above ex.. For more reference, please consult\
 your dealer.
:­:À:»:¼:Æ:©
:™
:ž
:˜:Ì:»:À:Æ:w:£
:˜:Ì:»:À:Æ:w:©
SCART connector (jack)
SCART cable
(plug) RCA plugs
3M\231 Digital Projector X64 
 \251 3M 2007.  All Rights Reserved.   
						

							
6
Connection to the ports (continued)
NUSB
USB B type jack
Pin Signal1 +5V
2 - Data
3 + Data
4 Ground21
34
ON
OCONTROL
D-sub 9pin plug
• About the details of RS-232C communication, 
please refer to the following page.
Pin Signal Pin Signal Pin Signal1 (No connection) 4 (No connection) 7 RTS
2 RD 5 Ground 8 CTS
3 TD 6 (No connection) 9 (No connection)
9
1
2
3
4
5 6
7
8
3M\231 Digital Projector X64 
 \251 3M 2007.  All Rights Reserved.   
						

							
7

Command Control via the Network
Command Control via the Network
Connecting the cable
1.
Turn off the projector and the computer.
2.
Connect the CONTROL port of the projector with a RS-232C port of the 
FRPSXWHUE\D56&FDEOHFURVV8VHWKHFDEOHWKDWIXO¿OOVWKHVSHFL¿FDWLRQ
shown in the previous page.
3.
Turn the computer on, and after the computer has started up turn the 
projector on.
Communications setting
19200bps, 8N1
1. Protocol
Consist of header (7 bytes) + command data (6 bytes)
2. Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
&5&BORZ/RZHUE\WHRI&5&ÀDJIRUFRPPDQGGDWD
&5&BKLJK8SSHUE\WHRI&5&ÀDJIRUFRPPDQGGDWD
3. Command data
Command data chart
byte_0 byte_1 byte_2 byte_3 byte_4 byte_5
Action Type Setting code
low high low high low high
Action (byte_0 - 1)
Action &ODVVL¿FDWLRQ Content
1 Set Change setting to desired value.
2 Get Read projector internal setup value.
4 Increment Increment setup value by 1.
5 Decrement Decrement setup value by 1.
6 Execute Run a command.
6 7 8
9
123456
7 8
9
12345
CONTROL port RS-232C cable (cross) RS-232C port
of the projector of the computer
- (1) (1) CD
RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR
GND (5) (5) GND - (6) (6) DSR
RTS (7) (7) RTS
CTS (8) (8) DTS - (9) (9) RI
3M\231 Digital Projector X64 
 \251 3M 2007.  All Rights Reserved.   
						

							
8
Command Control via the Network (continued)
Requesting projector status (Get command)
(1) Send the following request code from the PC to the projector.
 Header + Command data (‘02H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
(2) The projector returns the response code ‘1DH’ + data (2 bytes) to the PC.
Changing the projector settings (Set command)
(1) Send the following setting code from the PC to the projector.
Header + Command data (‘01H’ + ‘00H’ + type (2 bytes) + setting code (2 bytes))
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’to the PC.
Using the projector default settings (Reset Command)
(1) The PC sends the following default setting code to the projector.
 Header + Command data (‘06H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
7KHSURMHFWRUFKDQJHVWKHVSHFL¿HGVHWWLQJWRWKHGHIDXOWY DOXH
(3) The projector returns the response code ‘06H’ to the PC.
Increasing the projector setting value (Increment command)
(1) The PC sends the following increment code to the projector.
 Header + Command data (‘04H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
(2) The projector increases the setting value on the above setting code.
(3) The projector returns the response code  ‘06H’
 to the PC.
Decreasing the projector setting value (Decrement command)
(1) The PC sends the following decrement code to the projector.
 Header + Command data (‘05H’ + ‘00H’ + type (2 bytes) + ‘00H’ + ‘00H’)
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code  ‘06H’ to the PC.
When the projector cannot understand the received command
When the projector cannot understand the received command, the error cod\
e  ‘15H’
is sent back to the PC.
Sometimes the projector cannot properly receive the command. In such a c\
ase, 
the command is not executed and the error code  ‘15H’is sent back to the PC. If 
this error code is returned, send the same command again.
When the projector cannot execute the received command.
When the projector cannot execute the received command, the error code  ‘1CH’ +
‘xxxxH’  is sent back to the PC. 
When the data length is greater than indicated by the data length code, \
the 
projector ignore the excess data code. Conversely when the data length i\
s shorter 
than indicated by the data length code, an error code will be returned t\
o the PC.
NOTE ‡2SHUDWLRQFDQQRWEHJXDUDQWHHGZKHQWKHSURMHFWRUUHFHLYHVD QXQGH¿QHG
command or data.
• Provide an interval of at least 40ms between the response code and \
any other code.
• The projector outputs test data when the power supply is switched ON, an\
d when the 
lamp is lit. Ignore this data. • Commands are not accepted during warm-up.
3M\231 Digital Projector X64 
 \251 3M 2007.  All Rights Reserved.   
						

							
9

Names Operation Type HeaderCommand DataCRC Action Type Setting Code
Power Set Turn off BE EF 03 06 00 2A D3 01 00 00 60 00 00
Turn on BE EF 03 06 00 BA D2 01 00 00 60 01 00
Get BE EF 03 06 00 19 D3 02 00 00 60 00 00
[Example return] 00 00 01 00 02 00[Off] [On] [Cool down]
Input Source Set COMPUTER1 BE EF 03 06 00 FE D2 01 00 00 20 00 00
COMPUTER2 BE EF 03 06 00 3E D0 01 00 00 20 04 00
COMPONENT BE EF 03 06 00 AE D1 01 00 00 20 05 00 S-VIDEO BE EF 03 06 00 9E D3 01 00 00 20 02 00VIDEO BE EF 03 06 00 6E D3 01 00 00 20 01 00
Get BE EF 03 06 00 CD D2 02 00 00 20 00 00
Error Status Get BE EF 03 06 00 D9 D8 02 00 20 60 00 00
[Example return] 00 00 01 00 02 00 03 00
[Normal] [Cover error] [Fan error] [Lamp error] 04 00 05 00 06 00 07 00
 >7HPSHUURU@ >$LU